Discharge
-
Product
Dual Surge Current Generator
MIG0612T-K12
-
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
Product
Analogue (1kV below) Insulation Tester
8031 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 2Ω & 20Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
Product
Digital (1kV below) Insulation Tester
2151 IN
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 68 × 34mm(2.677” × 1.338”) large LCD display.● 3½ digital LCD(2000 counts) a LCD indicated instrument for insulation.(MΩ), continuity(Ω) and AC voltage.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA DC load.● >200mA short circuit testing current for a resistance tests.● Auto ranging.● REL function.● Auto power OFF.● Fuse protection.● Auto data hold.● BS 16 edition.
-
Product
Advanced Battery Tester
DBT-12+
-
The tester enables safe measurement of voltage, current rating, state of charge and state of health for 12V and 6V batteries. The device is powered by an internal battery, so it can test even discharged batteries and can be conveniently used as a voltmeter.
-
Product
Basic Fuel Pressure Tester Kit
FIT450
-
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose.
-
Product
Battery Charger-Analyzer for small battery systems (up to 10A-Hr)
24-400xg
-
The 24-400XG is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the 24-400XG can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights inform of the status of the operation.
-
Product
Lightning Warning Sensors
-
Lightning warning sensors measure the local, atmospheric electric field at the earths’ surface and the fluctuations in field strength. By monitoring the field strength, the potential for cloud-to-ground (CG) lightning discharges can be detected, and advance warning can be made when conditions are becoming favorable for lightning.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Battery Testing
BTS 200
-
This testing and maintaining battery system allows to perform measurement of battery voltage, discharging current test and testing of battery capacity. BTS 200 can be connected with external load unit ELU 200.
-
Product
MINI Battery Discharger & Capacity Tester
IDCE-4815CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-4815CT can provide 0-150A (steps:1A) adjustable current for different test requests
-
Product
PMS Leak Test System
-
The system (Pressure Measuring System) is a portable, complete system for leak tests. This consist of the pressure test kit PMS3000 for performing leak tests with an integrated graphic-capable 4.3” color touch display and a pressure relief kit DAK2000 for discharge test according to W400-2, Part 16 pressure loss methods as well as DIN EN 805. The system is complemented by a variety of connection accessories like the rugged accessory case (individually equipped), the test standpipe PSR and accessories for building gas connection as well as the electronically controlled test pumps EPP and the compact air compressor KLK1030.
-
Product
DC Electronic Load
EE15120A
-
The EE15120A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices. The electronic load can act as a Current Regulator for charging
-
Product
Insulation Tester
AD-2050
-
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation. 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
Product
High-concentration, High Flow Ozone Generator
SEMOZON® AX8407
-
The SEMOZON AX8407 generator converts pure oxygen into ozone through silent electrical discharge and achieves high output and high concentration level. It requires only minute levels of dopant nitrogen gas, far below the levels required for competitive ozone generators. As a result, the presence of contaminants, e.g. NOx compounds, is extremely low.
-
Product
MASTER FUEL PRESSURE TEST KIT
FIT550
-
*Performs running, residual, rail and flow rate pressure tests*Large, easy-to-read 3-1/2" dual-scale gauge reads 0-100psi and 0-700 kPa*Kit includes: 50+ adapters, fittings, 48" hose, pressure relief and fuel discharge hose to test most domestic and foreign fuel injection systems*Also includes quick release couplers and adapters to fit other fuel injection test kits*For use with gas engines only
-
Product
Sludge Density Meter
SD-40
-
Type SD-40 detects the density of sludge discharged from sedimentation tank and concentrators, in sewage treatment plants and water works. It achieves the accurate observation of sludge density, and helps to control the discharge of sludge.
-
Product
Insulation & Multifunction Tester (LCD Display)
1155 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Sixteen Channel, 12-Bit Analog Input Card
PCI-AI12-16(A)
-
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
Product
Portable GIS Partial Discharge Detector
JHPD-10
-
Xiamen Jiahua Electrical Technology Co.,Ltd
JHPD-10 quickly and accurately detects various kinds of partial discharge signals that occur with insulation defects in GIS. Attached on the surface of GIS the detector collects the inside discharge signal of impure gas, suspension potential and solid insulation material. The diagnostic software analyzes the fault character and locates the fault to avoid electricity accident. The device is for daily patrol inspection with high efficiency and easy operation features. Designed with two UHF signal channels, one detects the partial discharge signal; another excludes the disturbance signal like corona discharge in the air and mobile phone communication.
-
Product
Passive Component ATS
-
Test and packing speeds from 80ppm to1,800ppmStandard functions - Inductance/quality factor test - Winding resistance test - Polarity testOptional functions - Layer short test - Insulation resistance test - Bias current testCircular vibrating plate design feeds inductors steadily and rapidlyIndex disc design eliminates dropped inductorsFour-wire measurement test socket designAutomatic discharge mechanism when feeding errors occurEach test station has an independent NG (No Good) product collection boxTest without packaging function provided, good products gathered in bulk collection boxExclusive data collection software designed for monitoring product quality in real timeReserved stations for number spraying and automatic optical inspectionSwitchable Chinese/English/Japanese operating interfaceEquipment is fast, stable and safe
-
Product
Analogue (1kV below) Insulation Tester
1652 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
Product
DC Electronic Loads
-
Keysight DC electronic loads provide you with the flexibility to test a wide range of applications from power-supply test to simulation of high-intensity discharge (HID) headlamps. The 16-bit voltage, current and power-measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Product
Supercapacitor Test
-
The CT3001A/C battery test systems are upgraded from CT2001A/C with higher precision and data logging rate. The tester can be used to run precision tests for coin cells, pouch cells, prismatic cells, and especially supercapacitors (ultra-capacitors). Each tester has 8 independent channel which can be programmed to run constant current charge/discharge, constant voltage charge, constant power discharge, constant resistant discharge, and direct current internal resistance (DCIR) tests.
-
Product
Portable Strain Gage Welding and Soldering Unit
700
-
A battery-operated capacitive discharge spot welder for attaching and wiring weldable strain gages and temperature sensors.
-
Product
Battery Analyzers
Beta D-50
-
*Analyzer for any type of battery.*Adjustable constant current discharge from 0 to 50 Amps.*Set for Amp-Hour capacity reading.*Accept or Fail lights Indicators for a GO/NO-GO Test.
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Ultrasonic Leak Detector
ULD-410
-
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-410 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure.
-
Product
Intelligent Battery Tester
CHROME
-
Simulating a 20 hour discharge test in seconds, the ACT CHROME displays the DC Voltage and available Ampere hour (Ah) capacity of standby lead acid batteries between 1.2Ah and 200Ah.
-
Product
Battery Load Bank
K-3980
-
Kongter Test & Measurement Co., Limited
Kongter offers a series of customized DC load banks with many different models for constant current battery discharge test and battery capacity test. They cover a wide voltage range from 12V to 480V nominal voltages with current up to 600A. They are widely applied in various industries. With its optional battery Data Acquisition Case (DAC), discharge values of EACH cell could be monitored in battery load bank and PC software simultaneously by using Kongter’s data view software.
-
Product
110V / 100 Amp Load
BD12-110P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
