Traces Wire
Identify a wire's path.
-
Product
DB9 To 10-Pin Wiring Board
OPT1-DB9E
Terminal Block
DB9 to 10-pin wiring boardDimension: 35 x 42 x 20mm
-
Product
Trace Moisture Analysis System
-
Analyzing moisture, and how much of it, is critical to the performance of petroleum products, as well as infrastructure and product integrity. For example, moisture in petrochemical feedstock can cause pipelines and valves to freeze, as well as poison some catalysts. One popular method used to analyze for moisture is Karl Fischer Titration (KFT). KFT has a wide dynamic range but has difficulty in measuring relatively low amounts of moisture. In addition, there are the well-known problems of side reactions and known interferences.
-
Product
Drawing Die And Wire Measurement
Drawing Die Inspector DDI
-
Optik Elektronik Gerätetechnik GmbH
Special microscope setup for visual inspection of wire drawing dies.
-
Product
N2O/H2O Trace Gas Analyzer
LI-7820
-
The LI-7820 N2O/H2O Trace Gas Analyzer offers high-precision nitrous oxide measurements in a low power, portable design—enabling it to easily integrate into survey and long-term soil flux systems. Pair it with the LI-7810 CH4/CO2/H2O Trace Gas Analyzer or LI-870 CO2/H2O Analyzer for CO2 and CH4 measurements at your site.
-
Product
Wire Crimp Pull Sensor
Model MR06-200
-
The MR06-200 wire crimp pull sensor is a hand-operated solution for measuring wire crimp pull-off forces. The ergonomic handles and convenient tensioning mechanism make field measurements a breeze for applications up to 200 lbF (1,000 N). Squeeze the handles together to increase tension on the sample until a break occurs. The peak force is recorded by a Mark-10 indicator. A rotating turret with slots of multiple sizes accommodates a wide range of wire diameters, up to 0.25 in. (6.4 mm).
-
Product
Wire Tracer
LKZ-700
-
Wire tracer LKZ-700 is designed for detecting of cables and conductors in various environments (concrete, brick, wood, ground) being under voltege, without the need to disconnect any devices from tested network, as well as in non-voltage environments.
-
Product
Wire Sorter
-
Shanghai Beha Electronics Co., Ltd.
*Standard signal transmitter identifies up to 12 lines*Clear indication of short circuits, open circuits, or interruptions*Integrated continuity tester
-
Product
Bespoke Wire Rope Solutions
-
Wire ropes with customized end fitting, or MS Standard Wire Ropes.
-
Product
Vibrating Wire Peripherals
-
Many Campbell Scientific vibrating-wire peripherals enable dataloggers to read vibrating-wire sensors (also known as vibrating-wire or vibrating-strip transducers). These sensors measure strain, load, pressure, and water level, and they output a frequency signal generated by a vibrating filament. Campbell Scientific also offers vibrating-wire dataloggers that read the sensors directly.
-
Product
Glow Wire Test Apparatus
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
Product
Probes With Lead Wires
-
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.
-
Product
Wire Tracer
-
*Detect through the shielded cable*Instantaneous finding of AC current*Tracing cables*Monitoring current status in applicances*Compares the AC current*Tracing cables inside the wall*Locating underground cables*Detects magnetic field*Low voltage high current detection
-
Product
Wired Solutions
-
For more than 65 years, VPC has honed its expertise in wiring services, ensuring exceptional quality in manufacturing quality-tested cable assemblies, patchcords, enclosures, and more to complete your interconnect solution.
-
Product
Automatic Wire Test Set
AWTS
-
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
Product
Field Portable Wire Analyzer
Model 2635
-
The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.
-
Product
Control Wires Surge Suppressors
AS-8SP / AS-12SP / AS-16SP
-
Array Solutions Control Wires Surge Suppressors
-
Product
Process Trace Oxygen Analyzer
NL-IN96
-
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
GNL-IN96 trace oxygen analyzer is an intelligent analyzer that is based on microprocessor. It adopts fuel cell oxygen sensor, can measure oxygen concentration in 0-25% of oxygen, and it tests best in 0-1000ppm of oxygen. - See more at: http://en.ci-ele.com/8aedb8bf-ef48-4f8c-127a-797c939a6181/eb29c97a-af95-5fcd-f4a9-f48f6290407f.shtml#sthash.Sirfx2VB.dpuf
-
Product
Trace Viewer (Software Application For Trace Analysis)
-
TraceViewer application provides you with a full range of options when analyzing traces (information on the condition of a fiber at any given point of its length, received from the optical time-domain reflectometer) - receiving, viewing, editing and labeling.
-
Product
Trace Moisture Analyzer
Model 8800P
-
Teledyne Analytical Instruments
The 8800 series uses field proven aluminum oxide (Al2O3) sensing technology to accurately detect trace moisture on either a continuous or spot checking basis. All Al2O3 sensors share the same basic operating principle: the capacitance measured between the sensor’s aluminum core and gold film deposited on the oxide layer varies with the water content. The 8800 series moisture sensor employs unique Hyper Thin Film (HTF) technology, which offers three major structural improvements in Al2O3 sensor design. These structural changes, noted below, provide the user with increased sensitivity, greater stability and a quicker response time when compared to other conventional aluminum oxide sensors on the market today.
-
Product
Trace Extensions
-
Trace based debugging adds a powerful set of features to complement and enhance your existing debug tools. Many modern devices include a trace port which is capable of providing real-time, non-intrusive information about program flow and data operations. This can be used to work out where code has been, how long things took, to analyze task switches, interrupts, and to generate code coverage reports. If you think of traditional debugging as a series of snapshots, then trace-based debugging is a video with timestamps.
-
Product
5 KN Grips For Fine Wire
-
These grips offer a suitable method for tensile testing soft metal wires, ropes, and strings, all with a diameter of 3 mm (0.12 in) or less. The upper and lower grips include an articulated joint to maintain alignment of the specimen with the testing axis during testing.
-
Product
Wire & Cable Testers
-
Precision Mastech Enterprises Co.
Diagnostic tools designed to verify electrical connectivity, map wiring configurations, and detect faults.
-
Product
DB25 DIN-Rail Wiring Board
ADAM-3925
-
Low cost universal DIN-rail mounting screw terminal module for PC-LabCard products with DB25 connectorScrew-clamp terminal blocks allow easy and reliable connectionsCase dimensions (W x L x H): 77.5 x 56.3 x 51 mm (3.1" x 2.2" x 2.0")To Be Used With PCI-1757UP, PCL-833
-
Product
PDS Wire Crane Monitoring System
-
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
-
Product
1 KN Capstan Grips For Yarn And Wire
-
These capstan grips are applicable for tensile testing yarn and metal wire with thickness less than 3 mm (0.12 in). Flat grip faces are used to hold the specimen. The grip faces are opened and closed by a cam with an operating lever. Ease-of-use and simple design are advantages of these 1 kN capstan grips for yarn.
-
Product
Trace Gas Analyzer
PTR-TOF 4000
-
The new PTR-TOF 4000 is a compact, ultra-sensitive & high-resolution IONICON PTR-TOF real-time trace VOC analyzer. It is our first high-resolution PTR-TOFMS built into the same small and lightweight layout known from our successful PTR-TOF 1000 series. It also features the new hexapole ION-GUIDE technology for increased sensitivity and resolution. The PTR-TOF 4000 thus allows you to benefit from both high mass resolving power and high-sensitivity. Like the other instruments built on this platform also the PTR-TOF 4000 demonstrated its reliability and robustness but also its remarkable technical abilities and speed during various international campaigns (e.g. NASA's KORUS-AQ).
-
Product
Glow Wire Tester
TF346
-
TESTEX Testing Equipment Systems Ltd.
Glow Wire Tester, to determine the resistance to fire insulating parts. The testing of electro-technical products for fire hazard is conducted by simulating as closely as possible actual effects occurring in practice. Parts of electro-technical equipment which may be exposed to thermal stress due to electric effects & deterioration of which may impair safety of equipment shall not be unduly affected by heat & fire generated within the equipment.
-
Product
Handheld Wiring Analyzer
HT-128+
-
Reduce your wire harness assembly and installation difficulties now. The NEXU HT-128+ test platform provides a valuable tool for multi-point wiring continuity analysis. Our versatile, lightweight, handheld unit can serve your wiring test and maintenance needs from harness layout to product field support. The HT-128+ performs testing and troubleshooting, automated ring-out, directed assembly plus other features to resolve wiring issues quickly to achieve increased product availability!
-
Product
Glow Wire Apparatus
GW-4
-
Is designed to perform tests specified in many standards to check Resistance to Fire in Insulating parts. The best method for testing electro-technical products with regard to fire hazard is to duplicate exactly conditions occurring in practice.
-
Product
3 Wire (Digital) Earth Resistance Tester
2720 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
