Continuity Testers
Verify circuits by providing an audible or visible indication when a sufficiently low resistance is applied between input probes.
-
Product
Portable Circuit Breaker Tester
PI-1600
-
The PI-1600 Circuit Breaker Tester incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-1600 test set is two testers in one, incorporating the PI-800 and PI-AUX. The PI-800 section can be used alone, on 120 or 240 VAC supplies, generating continuous current of 400, 800, amps at 4.2 kVA, with peak output to over 10x. When configured for the PI-1600, the PI-AUX output unit is connected in series or parallel to the PI-800. The PI-AUX boosts total power to 9.8KVA, and allows testing of draw-out breakers and MCB’s to 1600 Amps. The units are housed in rugged interlocking suitcase-size enclosures. Each piece weighs no more than 125 pounds, allowing one-person hand truck mobility. Basic operation is very simple, and the proven MAC-21 control instrumentation provides optimal output control and measurement. The MAC-21 instrumentation is supplied in a separate rugged portable case, interlocks on top of the PI-800, and connects to a cable in the rear of the test set.
-
Product
Dual Voltage Detector / Maintenance Tester
MicroPhase I
-
Hachmann Innovative Elektronik
MicroPhase I is an easily operated phase comparator, dual voltage detector and maintenance tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-testers warn against defect interfaces. The integrated "Universal Phase Comparator" compares two different interface signals, even if they are of different interface type or voltage. A unique error control avoids switching errors caused by erratic or unfeasible phase comparison.
-
Product
Hardness Tester
-
Jinan Testing Equipment IE Corporation
Hardness is the property of a material that enables it to resist plastic deformation, usually by permanent indentation. Indentation hardness measures the resistance of a sample to material deformation due to a constant compression load from a sharp object; they are primarily used in engineering and metallurgy fields. The tests work on the basic premise of measuring the critical dimensions of an indentation left by a specifically dimensioned and loaded indenter.
-
Product
Battery discharge testers
-
The battery discharge testers are used to test batteries by discharging them in a specified mode: given resistive load, fixed discharge current, etc. Depending on the required power rating, various sizes are available from manually transportable testers to multiple electronically controlled units in a master/slave configuration. Five Series of standard models.
-
Product
Instruments Transformers Tester
Calport 100 Plus
-
Calmet Smart Calibration Devices
Three phase instrument transformers and electricity meters tester class 0.1 or 0.2. It makes possible CT and PT testing on site or in the laboratory. We recommend a new replacement - TE30 Working Standard
-
Product
Digital Relay and Merging Unit Tester
POM2-3333
-
POM2-3333 Digital Relay and Merging Unit Tester is equipped with 6*12.5A and 6*120V outputs, 8 pairs of BI, 4 pairs of BO and 6 fiber optic ports, built-in GPS, supporting PPS, IRIG-B, PTP/IEEE1588 time synchronization.
-
Product
Heavy Duty Circuit Tester / Jumper
32900
-
Heavy-duty circuit tester for checking low voltage up to 12 volts. By depressing the red button the tester becomes a jumper for powering electrical components or a ground. The probe, handle, cord and clamp are reinforced for durability. Comes with a strain relief spring on the cord.
-
Product
Insulation Resistance Tester
UDH-50-1-T
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated• Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV • Resistance range to 1TΩ • Continuous digital display on LCM• Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
Product
Pitot-Static Tester
PS-500
-
The PS-500 Pitot-Static tester is a low-maintenance digital tester that is fully portable.
-
Product
AATCC Wrinkle Recovery Tester
M272
-
To determine a fabric's ability to recover after wrinkling under a predetermined load for a set period of time. Set of 3-D plastic replicas are available to grade fabrics.
-
Product
Compact Tester
-
Designed for testing a family of products with similar functionality. A cost-effective solution for simple PCB architecture. Measurement system integrated with the adapter. Allows the use of interchangeable adapter inserts, including tandem type. Allows you to expand the scope of functionality. Optional interchangeable adapters (fixtures). Perfect for low-volume production
-
Product
Resistance Tester With Leakage Current (Loop Current)
GT00WD00ZY
-
*screen display*Double protection insulation*Non-contact measured resistance, safe, fast
-
Product
Voltage Testers
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
Non-contact detection of 50 to 1000V ACRugged and double molded caseSuitable for outlets or against wire insulation testingFlashing red LED light indicatorBuilt-in bright flashlight with on/off buttonConvenient size with pocket clipAuto power offSystem self testUse on 50/60Hz circuitsComplete with two AA batteriesCATIII 1000VDimensions: 158 x 21mmWeight: 48g
-
Product
Environmental Control System (ECS) Tester
H301
-
The H301 Environmental Control System (ECS) Tester measures and displays parameters required to test and troubleshoot aircraft heating and air conditioning systems. These parameters include temperatures, pressures, AC and DC voltages, DC currents, and resistances.
-
Product
CANbus Network Tester
-
Automatic Pin Test - automatically checks any abnormality on the OBD2 port caused by shorting (i.e., Pin 16 Power shorted to Ground), reverse polarity, and any other abnormalities
-
Product
Hamburg Wheel-Tracking Tester
-
The Hamburg Wheel-Tracking Tester is used to test submerged, compacted Hot Mix or Warm Mix Asphalt specimens as per standard.The device consists of a reciprocating wheel that is rolled over the specimens while measuring the rate of permanent deformation. A constant load of 705 N ±4.5 N is applied to the specimens with a sinusoidal wheel speed of 1 ft/sec in a constant temperature controlled water bath up to 70 °C (± 1.0 °C). An LVDT jig is used for continuous measurement of permanent deformation along the path of the rolling wheel. Accommodates cylindrical or slab specimensSoftware for automatic determination of Stripping inflection PointNumber of passes to SIP, number of passes to failure and other calculated parametersStainless steel construction with temperature controlled water bath up to 70ºC
-
Product
Fabric Unidirectional Water Transmission Performance Tester
DRK-UPT1
-
Shandong Drick Instruments Co., Ltd.
The unidirectional water transmission performance tester is a special instrument for measuring the unidirectional water transmission performance of textiles.
-
Product
VME Bus Tester
VBT100
-
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
Product
Earbud Tester
BK2132
-
When you don't need the full power of a BK2120A speaker tester, then the more portable BK2132 might be what you are looking for. This little machine is based on the more sophisticated system but it provides only basic testing. It is very fast and easy to set up and use and is especially portable as well, all for a lower price.
-
Product
Pole Plug Tester
SAE 7
-
When there’s no time to waste the SAE 7-Pole Plug Tester provides a fast, easy way to isolate lighting problems to the tractor or trailer. Use it to test the output of SAE 7-pole tractor light cords, while connected to the tractor or to your Square Wheel Industries Trailer tester.
-
Product
Intelligent Tangent Delta Tester of Enamelled Wire
TD-8S
-
Shanghai Dean Electrical Co., Ltd
·Tangent Delta Tester is used for testing the curing degree of enamelcover. The curve variation of tgδ shows the curing degree of enamelled wire directly, then adjust the heating temperature of enameling oven, to get a optimal curing degree of enamelled wire, control the wire quanlity effectively.·The temperature class of enamelled wire can be tested rapidly; the enamel type of wire can be determined preliminarily.
-
Product
Alternator/Battery Load Tester
6031
-
• Tests for defective alternator diodes including GM trio test• Performs complete battery test• 125 Amp load checks state of charge • Searches for excess starter current and alternator/regulator output voltage• Includes test lead set (610271)• Made in USA of US and Global Components
-
Product
DC In AC Clamp Tester
M-800P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Model 800P is the world’s first clamp meter which can detect small DC current in AC circuit in addition to general AC/DC current measurement.
-
Product
In-Circuit ESR & DCR capacitor Tester
236
-
This In-circuit ESR & DCR capacitor tester is designed to measure ESR (equivalent Series Resistance) on capacitors range from 0.47uF to 2200uF, in or out of circuit. The ability to trouble shoot in-circuit saves time and makes the 236 a must for anyone that tests or trouble shoots PCB (printed circuit boards).
-
Product
HDMI Cable Tester
MT-7062
-
Test all HDMI cables with Type A to A, A to C and C to C connectorsDesign with loopback function allows test HDMI type A to A, A to C on main unit.Automatically fast & slow scan for testing all conductors status in a cable, Manual test for step by step detecting individual conductors for intermittent faults.Automatically detect wiring on HDMI type A or type C condition in straight, short, open, crossover in all RGB conductors.Quickly troubleshoot and verify HDTV installation and DIY termination in the field.
-
Product
Circular Locus Tester
TF225
-
TESTEX Testing Equipment Systems Ltd.
Circular Locus Tester, to determine surface deterioration and quality of fabrics (wool, chemical fiber, mixed, kitted and woven fabrics). Circular Locus Tester complies with GB/T 4802.1-2008, etc.
-
-
Product
Gem Testers
-
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
A diamond tester is a portable device used to check the authenticity of diamonds and test materials for their thermal and electrical conductivity. It can accurately indicate if the stone is a real diamond based on the gem's physical properties.
-
Product
Force Displacement Testers
-
Force displacement testing measures how much force is required to displace or deform a specific component or material. It’s an important aspect of quality control in manufacturing as well as material science. It’s necessary to help ensure products are made to the proper standards and to verify the properties of certain materials. Imada provides a range of force displacement testers that provide precise and accurate measurements, with numerous features to help technicians complete testing as quickly and effectively as possible.
-
Product
Pocket Network Tester
LinkSprinter®
-
The LinkSprinter Pocket Network Tester verifies the functionality of copper Ethernet links and identifies errors in less than 10 seconds. The tester reveals network connectivity status and port information while ensuring documentation for every link. The comprehensive AutoTester measures PoE voltage, performs a switch test, and confirms the DHCP server is running and responsive. The tester also verifies gateway/router, internal IP service, and cloud reachability. When paired with the secure Link-Live Cloud Service, the Network Tester automatically uploads results and allows annotation of results enabling job supervisors to easily manage the progress of deployment and troubleshooting tasks assigned to their team.
