Proto Boards
-
Product
Electronic Boards
-
Computer Gesteuerte Systeme GmbH
The relay board 8AGN is a cost-effective board of the CM series, which is also used in our load modules, for example. It can be mounted on a 35 mm DIN rail. Currents up to 1 A at 30 V are possible. The maximum wire cross-section is 0.5 mm².
-
Product
HIL Breakout Board
-
Onboard 192 pin snap-in terminal dramatically simplifies the wiring between your control hardware and your HIL system. As soon as the system is up and running there are 192 test terminals for easy access to all the interface signals: firing pulses, control feedback signals and other analog/digital I/O signals.
-
Product
Mixed function mezzanine side card for CPCI-S CPU boards
SCX-PCIE
-
The SCX-PCIE is a mezzanine side card for EKF CPU boards, equipped with a PCIe® Gen3 packet switch, onboard NVMe and SATA mass storage, and high-speed front I/O.
-
Product
Demonstration Boards
SAMPULSE50GHz and SAMPULSE70GHzANT
-
The SAMPULSE50GHz and SAMPULSE70GHzANT are demonstration boards for Furaxa InP single channel sampler/pulser ICs. The SAMPULSE50GHz model contains a 2.4mm combined TDR input/output connector to the common sampler/pulser node in the IC. The SAMPULSE70GHzANT is similar, except that instead of a single-ended 2.4mm connector, the sampler IC's differential inputs are fed from a bowtie antenna. In both models, the IC's differential sampler output is converted, using an AD8009 op amp, into a single-ended ground-referenced output that is sent to an SMA jack labeled SAMPLER OUTPUT.
-
Product
Upgrade User-Installable GPIB Interface Board For AC6900B Series AC Sources
AC69GPBU
-
The AC69GPBU is a user-installable GPIB interface module upgrade for Keysight AC6900 Series basic AC power sources.
-
Product
Analog Isolation Board
MSXB 027
-
The MSXB 027 Analog Isolation Board accommodates up to 8 isolation modules in any combination of input and output. Up to 64 5B Analog Isolation Boards can be connected to a single DAP for a total of 512 isolated channels. When used in conjunction with Analog Output Expansion Boards, up to 66 of these channels can be specified as isolated analog outputs.
-
Product
General Purpose 4 Channel Optocoupler Board
-
A general purpose 4 channel optocoupler board using H11G2 optocouplers (see above schematic). Resistors, capacitors, and connections to terminal strip are made by customer to allow for complete flexibility
-
Product
PCI Data Acquisition Boards
DA14-100DMA Series - Dual 14-bit D/A, 15 MS/s
-
Model AD14-100DMA is similar to the ADDA14-100DMA, but does not have D/A converters.
-
Product
Overhead Board
TTC OVH-380-1
-
Curtiss-Wright Defense Solutions
The TTC OVH-380 is the processor-based controller (overhead) board for the TTC AIM/HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers and terminates the IP stack for Ethernet support.
-
Product
IC-PPC-VPX3d, 3U VPX QorIQ T2080 Single Board Computer
IC-PPC-VPX3d
-
The IC-PPC-VPX3d is a versatile 3U OpenVPX SBC for systems requiring high performance, low power and ample I/O. Based on the latest PowerPC QorIQ multiCore processor, it meets compute-intensive needs in industrial and harsh environments.
-
Product
Board Drivers
9450-DRV
-
IOWorks board drivers are Abaco Systems' IOWorks data acquisition and control (DAQC) software driver. It is a hardware and operating system-independent driver designed to support the widest variety of I/O in the industry. The driver operates with many operating systems such as Windows NT/Windows 2000, QNX, VxWorks, and Linux, and delivers high performance and flexibility across multiple platforms such as CompactPCI, VME and PCI.
-
Product
High Frequency Clock Divider Board
-
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
Product
PMC FPDP Board
MS 1741
-
- Four FPDP front panel outputs- FIFO buffering for real−time recording- FPDP Outputs: Two 80−pin FPDP connectors (A and B)- FPDP Outputs: Two 80−pin FPDP connectors(C and D)- Quantity: Standard: Two Front Panel Data Port (FPDP) connectors, each providing 32−bit output- Output Type: FPDP I, non−inverted configuration FPDP II, double the selected clock rate- Clock: On−board clock- FIFOs- Quantity: Four IDT72V3690 FIFOs, one for each FPDP port- Size: 32,768 x 36- Speed: FIFOs are capable of 166 MHz speed, but are run at one half of sample clock speed
-
Product
Single Board Computer
VF370
-
Sundance Multiprocessor Technology Ltd.
The VF370 is a 3U OpenVPX Single Board Computer (SBC) module that utilises the Intel Atom® E39xx series of embedded processors, Intel Cyclone® V FPGA technology and a FMC mezzanine site, to provide a module with scalable processing power and flexible IO options for reduced Size, Weight and Power (SWaP) applications. It is available in standard air-cooled and rugged conduction-cooled versions.
-
Product
Clock And Trigger Synchronization Board With Atomic Clock
CLKSYNC-PCI-AC
-
CLKSYNC-PCI-AC is a clock and trigger distribution board designed to provide up to eight synchronous clock and trigger outputs. The CLKSYNC-PCI-AC is designed for use with multi-channel, ADC and DAC systems where precise clock and trigger synchronization are required.
-
Product
Programmable Multifunction Counter Board, Isolated, With 2 Function Modules
CPCI-1711
-
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
Product
COTS PC/104 Carrier Cards and Boards
-
Sundance Multiprocessor Technology Ltd.
COTS PC/104 Carrier cards and boards
-
Product
12 Bit Waveform Digitizer Board
ATS9352
-
With data throughput as fast as 1.6 GB/s (1600 MB/s), ATS9352 is an ideal solution for many applications, including OCT, radar, ultrasonics, spectrometry and RF signal recording.
-
Product
Interface Board, Low Cost, 8:1 Ethernet RJ45
40-965-901
Interface
Low cost converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
Product
Answer Man Junior I/O Board
0001-011
-
A general purpose interface board for Mircromint's Answer Man Junior. Jumpers select one of three communication interfaces (RS-232, RS-485, or fiber optic RS-232). 12 bit ADCs and DACs are added for higher precision AD conversions. Answer Man Junior is included with the board.
-
Product
16-bit, 200KHz, 8SE/4DIFF Isolated Analog Input Board
APCI-3016-8
-
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
Product
Digital Input Board, 32 Isolated Channels, 24V
APCI-1032
-
32 digital inputs, 24 V or 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
Product
RS422/RS485 Serial Boards
104-COM-8S
-
These are eight, four, or two-port, asynchronous, serial communication boards designed for use on the PC/104 bus. They support RS-485 and RS-422 communications. The boards may be installed in any standard PC/104 stack. Connections are made via a 50 pin IDC type right angle connector.Common applications include POS, gaming systems, machine monitoring, military and high-density networking.
-
Product
Embedded Boards
UltraZed Family
-
Embedded boards are boards with processors, multiple integrated circuits, interfaces and other essential components assembled on it to serve a dedicated function. Embedded boards comprise multiple technologies, including processors, core logic, networking, connectivity, and multimedia components to provide functionality and performance for embedded system design applications. Embedded boards and solutions are normally employed to ensure a faster time to market for the developer. Applications of embedded systems vary from tiny portable devices, to large commercial and industrial installations, and even largely complex systems like medical or military or aviation purposes. Embedded boards can have single MCU chip or multiple MCUs depending on the complexity of application.
-
Product
Conduction Cooled Interface Board Supporting up to 5 Multi Function Channels
EXC-1553PMC/Px(S) / EXC-1553ccPMC/Px(S)
-
MIL-STD-1553, conduction cooled, interface board. Supports up to 4 multi function channels.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are multi-channel (up to four) MIL-STD-1553 interface boards for PCI Mezzanine Card compatible computers.Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes) and error detection (all modes) are supported on each channel.Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: PxS is NOT compatible to the MCH family of cards.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are supplied with C drivers, including source code, and Merlin+ Windows software.
-
Product
Thermal Load Boards
-
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
Product
LUTHER & MAELZER BARE BOARD TEST PINS
SERIES LMP 78
-
Materials and Finishes MATERIAL: Heat treated beryllium copper FINISH: 24 Kt gold plate over hard electroless nickel
-
Product
PXI Express Board Virtex-5 ADC Module
SMT791
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
Universal Development Board For The Plug-in Module PCAN-MicroMod FD
PCAN MicroMod FD Evaluation Board
-
The PCAN-MicroMod FD Evaluation Board is a development board for the PCAN-MicroMod FD and enables the design and development of your own circuits with CAN connection and I/O functionality. It can also be used for training purposes for CAN and CAN FD structures. The user can access the resources of the attached PCAN-MicroMod FD via taps, screw terminals, switches and potentiometers and test configurations or test circuits.
-
Product
Interface Board for 100 BaseT Ethernet
40-965-911
Interface
The 40-965-911 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 8 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of 100 BaseT Ethernet signals.
