DC Sources
A highly repeatable and stable DC voltage and current source.
-
product
Single Phase DC Injection Set Kit
PDC120A/PDC200A
PDC120A/PDC200A Single Phase DC current injection set kit is portable test set which could generate DC current for the various testings in railway transportation, HVDC converting stations, etc.
-
product
Precision Pulsed Current Sources
SpikeSafe Performance Series
SpikeSafe™ Performance Series Current Sources supply DC and precision continuous or single pulse current for light measurement and other applications. With sustained output power and no duty cycle limitations, Performance Series Current Sources support a broad range of applications.
-
product
DC Power Supplies
SG Series
AMETEK Programmable Power, Inc.
The Sorensen SG Series (hereafter SG Series) represents the next generation of high power programmable DC power supplies. The SG Series is designed for exceptional load transient response, low noise and the highest power density in the industry. With a full 15 kW available down to 20VDC output in a 3U package the SG Series leads the industry in power density. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units.
-
product
20 Bit Dual-Channel Reference Source
DRS20
The DRS20 is a dual-channel reference source offering ultra high precision and stability and provides a +/-10 V output. The output current can be up to 10 mA and the 4 wire connection provides a 1 µV/mA load regulation. The high precision and stability is achieved by using a temperature controlled voltage reference.
-
product
Bidirectional Programmable DC Power Supply(5kw ~ ±180kW)
FTB9000 Series
Shenzhen FaithTech Technology Co., Ltd.
FTB9000 series is a regenerative bidirectional programmable DC power supply, it is not only a stand-alone bidirectional DC power supply but also can be used as a regenerative electronic load, to absorb the consumed energy and feedback cleanly to the grid. The high-efficiency energy feedback efficiency not only saves electricity consumption and heat dissipation costs but also does not interfere with the operation of the power grid. It is widely used in high-power testing scenarios such as automotive electronics, new energy vehicles, photovoltaic energy storage, intelligent industrial equipment, battery simulation, etc.
-
product
Basic AC Power Source, 2000 VA, 310 V, 10 A
AC6803B
This basic AC power source offers stable, reliable power up to 2000 VA. An intuitive user interface and flexible I/O connectivity.Increase your uptime with stable, reliable AC power source.Engineer reliability into your designs with a basic AC power sourceTest your designs with confidence.Test under real-world conditions - fluctuating voltage or transient spikes.Easily access setup and measurement information.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
product
DC Blocks
A coaxial RF DC block is from Pasternack and has an 50 Ohm impedance. Our 50 Ohm DC block is manufactured with a SMA input and SMA output. This SMA DC block is an inner direct current block type.
-
product
DC Vibration Unit Tester
BK2116
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
product
Hand held, Battery-Powered Voltage Source
DVC-350A
Hand held, lightweight 11 ounce (342 grams)Laboratory accuracy of 0.015% of FSR at +25 C, traceable to the National Bureau of Standards4 1/2 Digit LCD display100 V incrementsTwo output voltage rangeDecimal: 1.2V dc, 12V dcHexadecimal: 1V dc, 10V dc
-
product
Mini Light Source Meter
MLS-100
•Stabilized Light Source•1310nm & 1550nm•Very small and lightweight•Controlled by Smartphone or PC via USB or Bluetooth•Smartphone application software and PC software•Li-ion Polymer Rechargeable battery•Battery charging via a USB interface•Universal 2.5mm adapter to accept FC, SC or ST•Reference light source for optical test
-
product
DC Power Supply
EP Series
A range of high grade laboratory power supplies capable of delivering upto 450W of power. These custom built models are easy to use, provide medium power, low voltage output and are capable of operating in laboratory or industrial environments. They havebeen designed keeping in mind the specific requirements of electronic and photometric laboratories and provide the most frequently required voltage and current ratings, while offering a safe overload protection. These power supplies are capableof supplying the maximum specified current at low voltage settings also.
-
product
Magnetoelectric DC Devices
Type Ma And Mb
Magnetoelectric DC devices type Ma and Mb and AMPETRAMETERS AND VOLTMETERS.
-
-
product
Light Sources
The unique dual-output of equivalent beams make it a useful source for many comparative applications in addition to wavelength calibration and so on. The two output beams originate from two views of the single emitting spot where the electron beam from the single hairpin filament collides with the interchangeable anode.
-
product
Multiple (8) High Power Four Quadrant Power Source
PM0825
The PM0825 consists of 8 fully independent four-quadrant power sources capable of supplying up to ±20V. Two of the sources are capable of up to 500mA each, four more are capable of performing at low levels with ranges of 1uA and 100uA; the remaining two are mid range with current ranges of 1mA and 100mA.
-
product
10-amp AC and DC Variable Power Supply
ACDC-10
The ETI Model ACDC-10 is a small, lightweight, and portable AC and DC power supply. The unit is intended for resetting circuit breaker charging motors and other general-purpose applications. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 1.4 kVA. The ACDC-10 is housed in a rugged plastic enclosure approximately 20” x 11” x 18” and weighs less than 65 lbs
-
product
Resolver to DC Sine / Cosine or Synchro to DC
ST-RD & ST-SD
Computer Conversions Corporation
ST-RD and ST-SD Series - Resolver to DC Sine / Cosine or Synchro to DC Sine Cosine Packaged on PCB with Track and Terminal Block and On-Board AC Reference Supply may be used driving DC Servo amp in active position synchronizing applications
-
product
Frequency To DC Isolating Transmitter
Model TWF / TWF2
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 ° C ± 5 °C• Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
product
3-Phase Programmable AC Source
Chroma Systems Solutions, Inc.
Delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA, suitable for commercial applications from laboratory testing to mass production
-
product
AC VOLTAGE MEASUREMENT (AC or AC + DC TrueRMS) Digital Multimeter
1320
± 199.9mV, ± 1.999V, ± 19.99V, ± 199.9V, ± 1200V, 5 Ranges, AC VOLTAGE MEASUREMENT (AC or AC + DC TrueRMS)
-
product
Full C-Band or L-Band Tunable Laser Source
LTS-2000
Hangzhou Huatai Optic Tech. Co., Ltd.
The LTS-2000 series full C-Band or L-Band quick adjustable laser optical source , is a 2U small model of high precision and muti-function, can be set up 1~4 port independent C or L band adjustable optical source. Various flexible configurations optional (see more in product series) , and makeing daily test and measurement applications greatly convenient.
-
product
(AC or AC + DC TrueRMS Digital Multimeter
1330
± 199.99mV, ± 1.9999V, ± 19.999V, ± 199.99V, ± 1200V, 5 Ranges
-
product
Digital Control DC Electronic Load
IT8200 Series
IT8200 series economical programmable electronic load,with the highest cost/performance ratio and small size, they are widely used in production testing lines and maintainance lines etc. Resolution 1mV/1mA ensures the accurate measurement result. IT8200 series has programmable performance, and can quickly recall 4 * 40 group memory data, panel function keys and display interface is clear, provide customers with simple operation program, easy and fast to complete a variety of complex tests. The series has CV, CC and CR mode, and short circuit test function, it is the most cost-effective electronic load products.
-
product
AC and DC 20-Amp Power Supply
ACDC-20
The ETI Model ACDC-20 is a rugged and portable 20-amp AC and DC power supply. Its applications include resetting circuit breaker charging motors and other general purposes. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1.92 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 2.8 kVA. The ACDC-20 is housed in a rugged plastic enclosure approximately 21.5” x 18.5” x 11.5” and weighs approximately 115 lbs.
-
product
Radar solution for fill level in DC & die casting
For quality control in DC casting (direct chill casting) and die casting, a continuous, high-precision level control of the steel and aluminum melt in the casting pit is required. Our radar sensors measure the filling level of molten steel, copper or aluminum in DC casting with a measurement accuracy in the sub-millimeter range – even at metal temperatures of up to 1600 degrees Celsius.
-
product
Tunable Laser Source
AP405xA series tunable laser sources are high performance external cavity Littman tunable lasers combining wide tuning range, high output power and high signal-to-noise ratio. Different wavelength ranges are available between 1000 nm and 1650 nm. Tunable laser sources OEM and stand-alone benchtop instrument versions are available. The TLS benchtop instrument is proposed with a friendly-user software, a touch sensitive screen, GPIB, ethernet , RS-232 and USB controls.
-
product
L Band Splitter, DC Block All Ports
PD5082
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
product
Three Phase AC Voltage Source
EAC-TAVS
Electronic Test & Power Systems
The EAC-TAVS is a series of programmable high power AC voltage sources. Each system provides a three phase true sinewave output as standard. Each unit is built in a freestanding cabinet. The output frequency is adjustable in the range of 45 - 105Hz. Different frequency ranges are optional, with up to 805Hz possible. An RS-232 and CAN interface are provided as standard. The high resolution TFT front panel displays a host of measurement and setting functions. Besides standard models, other nominal power levels and voltages can be user specified. Single phase and bidirectional versions are available on request.
-
product
SpikeSafe DC / Continuous Pulsed Current Sources
The Vektrex SpikeSafe™ DC / Continuous Pulse (DCP) Current Sources provide reliable DC or pulsed drive for LED or laser diode reliability testing, IESNA LM-80 maintenance testing, and other test applications requiring DC or continuous pulse current. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, accurate pulsing over long output cables, precise current, precision pulsing for improved measurement repeatability, and high power density — typically 6.4kW-8kW.
