Surface Contamination
-
Product
Fixed Writing Surface for 19" RA Cabinet
WSA-119
-
This fixed shelf / writing surface for a single-bay RA cabinet spans the full width of the cabinet and extends 18” in front.
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
-
Product
Absolute Contamination Standards (ACS)
-
The Absolute Contamination Standard (ACS) is used to calibrate instruments which size and detect particles on the surface of bare silicon wafers. Use ACS to characterize particles, before particles characterize products.
-
Product
Surface Mount Package Emulation
SMT Adapters
-
Ironwood’s SMT package emulation adapters are often called “surface mount feet” or “emulator bases”. These adapters provide access and interconnections to surface mount lands. Typically, the adapters are soldered to the target board in place of the IC device and provide a pluggable array of pins interface for sockets, probing adapters, package converters, and even board-to-board connections. These adapters are often utilized as a base for many of our probing adapter products. We constantly innovate to provide the most reliable, cost effective interfaces available. For example, many of our PLCC, QFP and SOIC emulation bases use our proprietary shaped solder techniques, replacing expensive, and often fragile, J-lead and Gull Wing leads. Shaped solder parts are easily fluxed and reflowed onto the target system. Our emulator bases can present either a male or female interface at 1.27mm or 1mm or 0.8mm pitch gold plated array pins for pluggable connection.
-
Product
0.25° Accuracy Full Attitude Surface Dynamic Motion Sensor
DMS-525
-
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
-
Product
Aluminum Electrolytic Capacitors (Surface Mount Type)
-
Panasonic Industrial Devices Sales Company of America
As a worldwide leader in Capacitor products, Panasonic provides a vast selection of Surface Mount Type Aluminum Electrolytic Capacitors featuring high reliability, long life, low impedance and high ripple current. With 30 Series to choose from, there's a Panasonic SMT Lytic Capacitor for any application.
-
Product
Surface Roughness Measuring Machines
-
Portable Surface Roughness Measurement instruments whose analysis function and operability are dramatically evolved
-
Product
Surface Profile Test & Measurement Products
-
PCWI Surface Profile Test & Measurement Products
-
Product
Chemical Analysis + Surface Analysis
-
Rocky Mountain Laboratories, Inc.
An independent surface chemistry and microanalysis laboratory to serve the needs of industrial, academic, and governmental clients. Our objective – to provide real-world solutions for industries with materials and process development needs – is as fundamental to our organization today as when we began. Over the years we have strived to adapt our services to the specific needs of these clients.
-
Product
19" Drawer with Writing Surface, Unshielded, 10.5"H x 30"D
DR-101930-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Portable Surface Roughness Tester Profilometer
SRG-2000
-
The PHASE II SRG-2000 surface roughness tester profilometer is a pocket-sized economically priced instrument for measuring surface roughness texture conforming to traceable standards. It can be used on the shop floor in any position, horizontal, vertical or anywhere in between.
-
Product
Surface Roughness Testers
-
Widely used in production site to measure surface roughness of various machinery-processed parts, calculate corresponding parameters according to selected measuring conditions and clearly display all measurement parameters.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS HL
-
Optik Elektronik Gerätetechnik GmbH
Measuring instrument for contact angle and surface free energy, special solution for semiconductor technology for wafers up to 300 mm.
-
Product
Surface Roughness Meters
-
This instrument is compatible with four standards of site to measure surface roughness of various machinery-processed parts, calculate corresponding and clearly display all measurement parameters.When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
Product
Photoemission And Surface Photovoltage Spectroscopy
-
KP Technology have developed a range of modules that feature surface photovoltage and photoemission spectroscopy capabilities.
-
Product
3D Sensor (Shiny Surfaces)
reflectCONTROL
-
reflectCONTROL is designed specifically to meet the high quality requirements that ensure high quality for shiny surfaces. The system based on deflectometry projects a striped pattern onto the measurement object. Defects on the surface cause deviations from the striped pattern which are recorded by cameras and evaluated by software.
-
Product
Surface & Volume Low Resistivity Meter for Conductive Materials
Loresta GP
-
The Loresta GX Meter is an intelligent, multi purpose low resistivity meter equipped with software that calculates resistivity correction factors. A variety of 4 pin probes are available for use with the Loresta GX. The instrument is typically used in Product Engineering, R&D, and Quality Control. Applications include measurement of conductive paint, conductive plastics, conductive rubber, conductive film, silicon wafers, antistatic materials, EMI shield materials, conductive fiber, conductive ceramics, etc.
-
Product
Surface Profilers
-
Taylor Hobson offers a world leading range surface form, surface finish and metrology solutions for 3D contour,ideal for the most demanding applications.
-
Product
Surface Resistance Meter
-
Wolfgang Warmbier GmbH & Co. KG
Starterkit for testing conductive an dissipative surfaces and electrostatic fields/surface potentials
-
Product
24" Drawer with Writing Surface, Unshielded, 7"H x 30"D
DR-072430-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Surface Mount Reed Relays
Series 200
-
Surface Mount Reed Relays. Wide range featuring dry or mercury wetted switches. Coaxial version for high speed digital or RF up to 6 GHz. 5, 12 or 24 volt coils with optional diode
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS Basic
-
Optik Elektronik Gerätetechnik GmbH
Low cost contact angle meter provides all functions for DIN conform measurement of contact angle and SFE.
-
Product
Mobile Surface Measuring
-
The mobile surface measuring instruments and analysis units from ZEISS are robust and easy to use. They are suitable for non-transportable workpieces.
-
Product
Non-contact Optical Surface Profiler
VS-OSP
-
The VersaSCAN OSP integrates the Base with a high-accuracy, high-speed laser displacement sensor. The OSP technique uses diffuse reflection mechanism to measure topography of a sample. OSP can be used to measure topography, as a very sensitive leveling mechanism, or charting topography to be implemented with other scanning probe techniques for constant-distance mode operation.
-
Product
Surface & Volume Resistivity Meter for Nonconductive Materials
Hiresta UX
-
The new Hiresta-UX is a high performance meter for measuring the surface and volume resistivity of a wide variety of nonconductive materials. With an extended measurement range of 103 ~ 1014Ω, this meter is ideal for Production, Engineering, R&D and Quality Control. The new Hiresta-UX features powerful new algorithms that automatically choose the right voltage, which optimizes the surface and volume resistivity testing. This versatile, high performance resistivity meter includes a built-in switch box that can be mated with a J-Box (meets JIS K 6911 for surface & volume resistivity and is compatible with ASTM D 257) as an option. The Hiresta-UX can store up to 2,000 measurement results, which can be easily exported to a USB memory device.
-
Product
Software For Visualizing Surface Quality
STATOVISION
-
Foerster Instruments, Incorporated
In combination with a STATOGRAPH module, the STATOVISION software enables the visualization of eddy current signals in a clearly arranged C-Scan. This results in an image of the surface quality of the components, allowing surface defects to be precisely localized. A major advantage of the STATOVISION software is the pattern recognition, which can be used for surpressing drill holes on brake discs, for example. The documentation of the entire scan is used for continuous quality assurance.
-
Product
Handheld Surface & Volume Low Resistivity Meter for Conductive Materials
Loresta AX
-
The Loresta AX Resistivity Meter a handheld unit measures the low resistivity of samples with consistent accuracy. This resistivity meter measures resistivity using a wide variety of probes. The Loresta AX uses a standard RCF that enables the user to input other RCF''s if known.
-
Product
Surface Mount Switches
-
Dow-Key® Microwave offers PCB mounted, miniature electro-mechanical microwave switches. These switches are designed with an overall size of 0.75” x 0.75” x 0.58” and weight of 0.5 ounces for test and aerospace applications where small size, reduced weight, and less power consumption are critical.
