PC
Checking personal computers and using a pc as host to perform test.
-
product
Fifo Serial Analyzer for DOS
FLL
FLL is a DOS based protocol analyzer for debugging serial asynchronous communication. FLL uses the standard COM1 and COM2 ports of a PC and does not require any other hardware except for the physical connection to the line.
-
product
ECM Noise Under RF Test System
BK8020
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
product
Handheld Water Quality Meters
LAQUA PH220
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers) - 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- °C & °F temperature readings- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrode and calibration solutions in carrying case- 3 years meter warranty
-
product
Dynamic Test System
3430-SW
The Dynamic Test System 3430-SW measures dynamic characteristics of IGBT/MOSFET devices at high speed. Maximum of 4 parallel measurement is available by connecting the 3430-SW mainframe test stations for each test items ( normal 2stations). One PC controls the whole system.
-
product
SPMI Protocol Analyzer and Exerciser
PGY-SPMI-EX-PD
Prodigy Technovations Pvt. Ltd.
SPMI Protocol Analyzer (PGY-SPMI-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. SPMI (System Power Management Interface) is a MIPI (Mobile Industry Processor Interface) standard with 2-wire synchronous serial, bidirectional interface that connects the integrated Power Controller(PC) of a System on- Chip (SoC) processor system with one or more Power Management Integrated Circuits (PMIC) voltage regulation systems.
-
product
Quality Control Program
ATB QC
The ATB Quality Control program has been used for 18 years all over the world. In the production of speaker, headphone, microphone, soundbox, PC, tablet and smartphone the quality is tested with the program and the Audio analyser ATB 804 USB.
-
product
PXI-7342, 2-Axis, Stepper/Servo PXI Motion Controller Module
779036-02
2-Axis, Stepper/Servo PXI Motion Controller Module—The PXI‑7342 is recommended for both simple and complex motion applications. It includes dual processors, a real-time onboard OS, and multiaxis interpolation. The PXI‑7342 offers blended motion trajectory control and fully coordinated circular, linear, point-to-point, gearing, and vector-space control in either embedded motion operation or host-centric programming environments. NI provides contouring capability for more complex moves. The onboard CPU uses an embedded real-time OS that has event-driven multitasking control. With this approach, several motion control programs and processes can operate simultaneously on the controller independently of the host PC and with no outside program interaction unless the host program or user configuration initiates it.
-
product
Saluki S2106X Series OTDR (up to 45dB)
S2106X series optical time domain reflectometer is an upgraded version with 7 inch larger display, higher operation speed and more friendly UI. It has rich external interface, which can realize remote control through Ethernet interface or two different USB interface for external USB flash drive, printer and data communication with PC.
-
product
Function Generator
FG-102
*0.3Hz~10MHz *Hz.KHz.MHz..3Range, Easy Operation.*LED: 0.56", 6 Digits. *2 Attenuator: (-20dB x 2) *USB (RS-232) Built-In.*PC Control: Frequency, Waveform, -20dB Attenuator. Duty Cycle*Accuracy: 10PPM, Longtiome: ±1ppm/year*Waveform: Sine, Square, Triangle to 10MHz*Duty Cycle Range 0.3Hz~3MHz
-
product
Pulsar 4 Channel Interface
Pulsar-4 7Z01201
Ophir’s 4 channel Pulsar interface turns your PC or laptop into a full fledged Ophir multi-channel laser power/energy meter. Just install the software, plug the laser measurement sensor into the Pulsar and the USB cable from the Pulsar to the PC USB port. With the Pulsar-4, you can connect up to 4 laser measurement sensors to each module, monitor each pulse at up to 25 kHz and utilize external trigger.
-
product
Benchtop RF Signal Generator
The Benchtop version of the Lucid series offers up to 4 phase coherent channels in a 2U 19” benchtop box. With a 5” touch display and front panel control buttons the Benchtop platform enables users to program the instrument without the need of an external PC. For synchronized, phase coherent, multi-channel applications such as quantum physics and phased array antennas the Benchtop platform is an ideal, high performance and cost-effective solution.
-
product
Fanless Embedded System With 7th/6th Gen Intel® Core™, Pentium® And Celeron® Processor, Compact Size For Video Analytics In Vehicle PC Market
UST100-504-FL
*CE, FCC certified; ISO 7637-2 compliant*LGA1151 7th/6th gen Intel® Core™ & Pentium® processors (up to 35W) with Intel® H110*Fanless and Wide operating temperatures from -40°C to +60°C*12/24 VDC power input, with power management (ACC ignition)*Single-sided I/O design for easy maintenance*Expansion capability for three PCI Express Mini Card slot and two internal SIM card slot
-
product
Embedded MultiCore Systems
Sundance Multiprocessor Technology Ltd.
Boards and systems that aren’t connected through an internal PC bus.
-
product
Fluid Level Sensor
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
product
CAN, CANopen, J1939 Tester
X-Analyser3
Warwick Control Technologies Ltd.
Graphical User Interface ideal for Windows PCs and tablets.• CAN, J1939, NMEA2000, CANopen, LIN and OBD – included into one tool• On-Board Diagnostics Scan Tool Features for Emissions ECUs.• CAN and LIN signal reverse engineering• Signals displays – text, scope and graphical such as gauges and lamps• Can be used for ECU or even network simulation• SAE J1939 database integrated with over 4000 PGNs and signals
-
product
Handheld Water Quality Meters
LAQUA PC220
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
product
Optical Spectrum Analyzer Module Specification
CA92001B
UCINSTRUMENTS CA92001B C band optical spectrum analyzer module is a spectral engine for Process Analytical Technology applications. The OSA module acts as a stand-alone spectral engine, imaging and measuring a wide range of vapors, liquids and solids through transmission and diffuse reflection in a rapid non-destructive process. Leveraging our proprietary Micro-Optic technology, UC INSTRUMENTS’ C band OSA module features the following characteristics: (1) compact; (2) light-weight; (3) low power consumption; and (4) wide wavelength coverage. These characteristics of UC INSTRUMENTS’ compact OSA engines are suitable for a variety of handheld, portable or bench-top OSA/spectrometer applications. Equipped with a state-of-the-art internal wavelength reference, the OSA module is capable of precisely measuring optical spectrum. Because it does not require an expensive InGaAs detector array, the compact OSA module is a cost-effective alternative to other grating-based OSA/spectrometer engines. The OSA communicates with a PC or an instrument motherboard via an USB interface. UCINSTRUMENTS’ OSA module platform can be installed or co-packaged into existing NIR OSA/spectrometers as a cost-efficient alternative to other scanning optical engines.
-
product
32 Channel Multievent QDC
V792
The Mod. V792 is a 1-unit wide VME 6U module housing 32 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance).For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section. Input range is 0 ÷ 400 pC.
-
product
14-slot CH-14 PXIe-PC Chassis
The new CH-14 PC PXIe-PC chassis with an embedded PC allows the creation of high-performance multifunctional systems for collecting and processing large flows of information, as well as systems for monitoring and adjusting radio-electronic equipment.
-
product
Pocket Colorimeter Illuminance Meter
HPC-3
Shenzhen Chuangxin Instruments Co., Ltd.
● Adopting micro-spectrometer technology which is more accurate than traditional photo-detectors .● Measure chromaticity coordinate temperature, chromaticity coordinate, rending index, color difference, etc● Data hold, save and open-function. Several groups of data can be saved. ● Accuracy of chromaticity coordinates :±0.003(x ,y)● 128*64 LED of graphic interface displaying spectrum wave, chromaticity diagram ● USB interface for PC communication ● Quality Li-Battery for recycled-utilization ● Range of wavelength：380nm－780nm； ● wavelength accuracy：±0.5nm Repeatability：±0.2nm ● Accuracy of chromaticity coordinate:±0.0025, Resolution：0.0001； ● Correlated color temperature：1500-25000K, Accuracy：±3%，Resolution：1K； ● Accuracy of total color difference：within±0.2 (under standard illuminate A）； ● Range of Illumination measurement：1.0lx-100klx; ● Accuracy of Illumination measurement：Class 1
-
product
Din Rail Temperature Transmitters
Datexel manufacture a large range of Din Rail Temperature transmitters. From fully isolated, PC programmable temperature transmitters, Dip Switch Programmable are just some of the features available on the Datexel range of Temperature Transmitters. Some units are dual channel to help save space in a panel.
-
product
Touch Screen Controller
EZT-570i
The EZT-570i Touch Screen Controller offers a 7" (18mm) or optional 10" (25 mm) touch screen and the latest in test chamber programming for ease of use . The controller comes standard with data logging, data file access via memory stick or PC, Ethernet control and monitoring, alarm notification via email or phone text message, data file backup, full system security, online help & voice assistance in multiple languages and more.
-
product
ISP Programmer Superpro Is01
Features:Until now,Support IC manufacturer, pcs devices and keeps growing.1)High speed thanks to the flexible hardware engine. Programming speed adjustable for complicated application environments brought by user target board, length of ISP cable etc.2)Stand-alone and PC-Hosted (USB2.0 High Speed) dual mode;3)Supports ISP programming of devices with I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 and any other serial port.4)ATE interface;5)Over-current and ESD protection to protect your equipment;6)DLL and API for easy integration into customers’ system.Hardware Specifications:1) ISP cable integrates I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 interfaces。2) VDD (0-5.5V /0.5A) and Vpp (0-15V / 0.2A) lines provided to power the target board and the target devices.3) Cable driver circuit supports target devices of voltage level 1.5-5V and is ESD protected.4) USB 2.0 (high speed) interface for PC hosted mode and management of project files on SD card.5) A 20 Characters x 4 lines LCD and a 6-key keypad are built with it for stand-alone operation. In stand-alone mode project files are stored on the SD card (up to 16GB). The number of the project files is limited only by the capacity of the SD card.6) ATE interface is built for easy external hardware control. 6 lines SEL0-SEL5 are for project selection (maximum 64 files); 2 command lines START and STOP; 3 STATUS lines PASS, FAIL and BUSY. All signals are optical-isolated.7) A universal AC adaptor of DC12V/2A is included for power supply.8)WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility.Software Specifications:1) Supports almost all devices with ISP interface.2) Supports Jam and Staple files from ACTEL and ALTERA; Direct C files from ACTEL.3) Programming speed selectable (High, Normal and Low) for complicated applications such as different cable lengths, different target load characters.4) Dynamic buffer function. Application examples include device S/N, MAC address, frequency or transducer calibration etc.5) File format on SD: FAT16, FAT32.6) Functions for IP protection: Project security, SD security, batch control, administration management etc. 7) API and DLL provided for easy integration into customers’ system like ICT and ATE.8) Software provides the features for multiple units to work concurrently controlled by USB HUB.Applications:1)R&D application like in-circuit test and debug.2)Volume production. Devices may be programmed after the board is fully assembled. One example is the serial number writing to an on-board serial device.3)Field application. Comes with portability, stand-alone mode and mobile data storage media (SD card), it is suitable for field test, debug and data acquisition.4)Third application modules. Friend s/w interface (DLL and Virtual Com communication command set) and h/w interface ( ATE and USB) are provided and make it very easy for customers to integrate ISP01 as a functional module into their systems. One example is the ICT equipment. With this integration user can finish in-circuit test and in-circuit programming in one step.
-
product
VHF/UHF Digital RF WATT/VSWR Meter
PMR 3030
The PMR 3030 EXT Power Meter is a very versatile instrument covering communication bands from 30-1000 MHz. (The PMR 3030 is available for 30-500 MHz only. The PMR Power Meter is capable of measuring forward and reflected power in the range of a few milliwatts up to 500 Watts. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters.
-
product
Digital Bit Pattern Generator
FAB-3226
The FAB-3226 Digital Bit Pattern Generator connects digital ports to an user-defined FPGA logic. As the FPGA is user-programmable all kind of operation can be implemented: input, output, and closed loop operation where input and output are processed in real-time. All this can be controlled by an user-defined application program running on a computer system (PC or embedded).
-
product
PCI GPIB Controller Card
Model 488-LPCI
* Adds GPIB Controller capability to any PC with a PCI bus.* Fast >1 Mbs transfer rate* 488.2V4 Driver supports 32 and 64-bit Windows XP, Vista, Windows 7, Windows 8 and Windows 10 with a true 64-bit DLL.* Driver compatible with industry standard 'ib' and '488.2' command sets.* Most affordable PCI-GPIB controller with a industry standard GPIB-32.dll.* Works with Agilent, NI and Kikisui VISA libraries.* ICS's Explorer auto configures your controller as it finds your instruments.* Use ICS's Explorer to control GPIB devices without having to write a program. * Program with Visual Basic, C, LabVIEW, Matlab or Agilent VEE* GPIB Card supports HP-IB Bus Systems.* Includes short bracket for lo-profile chassis.
-
product
Rack Mount Kestrel Chassis A-Series
0072
ATXstyle Motherboard, 3 x 5-1/4" Bays, 2 x 3-1/2". A 10-Slot HP 1000 backplane, cooling fans, and slides are provided plus space for a standard ATX PC motherboard, diskette and hard drives (3 x 5-1/4" and 2 x 3-1/2").
-
product
Fanless Embedded System With 4th Gen Intel® Core™ Processor For Railway PC
tBOX322-882-FL
The tBOX322-882-FL fanless railway embedded PC is based on 4th generation Intel® Core™ i7 or i3 processor with wide temperature capability from -40°C to +70°C. Certified with EN50155, EN50121 and complied with the standard of railway vehicles fire protection – PrCEN TS 45545-2, the railway PC is well suited for IoT & M2M-related applications such as onboard devices controller, train management, gateway, security surveillance and rolling stock environments. To keep all cables tightly secured, the railway pc has standard M12 connectors for Ethernet ports, USB ports, power input, and audio port. What is notable is that the graphics performance is now merely up to two times higher than previous generation, with the latest quad core processor, allowing faster and better information display.
-
product
Network Interface Controller
SPIDAR®
User interface and data acquisition embedded on the NIC:1. Any device with Wi-Fi can be used to change settings or view data collection2. No data collection interruption or data loss occurs if connection to PC or device is interrupted. No reduction in speed compared to running a single system. Daisy-chain NICs to deploy any number of GPR systems simultaneously; build Multi-frequency systems or Multi-channel Array systems Advanced timing control to ensure no interference between GPR systems
-
product
PCI Express CONET2 Controller
A3818
The Mod. A3818(*) is a PCI Express x8 card that can plug into both x8 and x16 PC PCI Express slot (V2.0), which allows the control of up to 4 CONET2 independent networks (each network can be made of up to 8 CONET2 slaves).
