Up Converters
Increase the frequency of a signal.
-
Product
DC/DC Converter 60 W
XRCM60-12DQF
-
DC/DC converter with 60 W from Bel Power Solutions | input ranges 16.8 - 137.5 VDC | output 12 V | operates in temperatures from -40 to +70 °C | provides 20 ms hold up time | O-ring FETs and built-in fuse
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Modulation Distortion Up To 13.5 GHz
S930701B
-
S930701B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 13.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930701B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Chassis - up to Four 8x1 or 4x2 Modules, or up to Four 8k Modules in a 4 RU Chassis
HXV/32-MF
Chassis
These Chassis controls up to 4 8x1 modules, 4 4x2 modules, or up to 2 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
Product
XMC GPU, Video & Format Converter Messanines
-
Curtiss-Wright Defense Solutions
Curtiss-Wright XMC format converters, GPU, and video processors fit conveniently onto existing modules equipped with a mezzanine site saving a backplane slot. Field-proven, our rugged modules feature powerful capabilities, including various input, output, and performance level options to meet your requirements.
-
Product
Thermal Voltage Converter
1395B
-
The 1395B TVC. Has better thermal stability than it's predecessor. Measuring ac voltages between 20 Hz and 100 MHz with increased accuracy and reliability. The 1395B can be used as a primary ac voltage standard and/or standard for the calibration of ac calibrators and voltmeters.
-
Product
1553 EBR to Ethernet Converter
ENET-1553-EBR
Ethernet Interface
ENET-1553-EBR-1D™ is an innovative product that provides “remoting” of 1553 AS5652 EBR operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). ENET-1553-EBR is a small, low-power, rugged device that provides connectivity for up to eight AS5652 RT devices, single BC or composite monitor.
-
Product
Chassis - Control up to 16 Modules with as Many as 32 Two Pole Relays Per Module Allowing 1xN Multiplexers up to 1020x1, 2 Pole Muxes up to 512x1 or 2xN Matrix Configurations up to 256x2
JX/256-MF
Chassis
These Chassis control up to 16 modules with as many as 32 two pole relays per module allowing 1xN multiplexers up to 1020x1, 2 pole muxes up to 512x1 or 2xN matrix configurations up to 256x2. Jumpering option allow the modules to be controlled as separate smaller muxes, i.e. 64 4x1 2 pole muxes, or combine specific groups to allow an almost unlimited combination of sizes. Add a Control Module and optional manual control to complete the system.
-
Product
MACC Protocol Converters
-
Introducing the ultimate solution for effortless communication between different protocols - our state-of-the-art MACC II protocol converter.This powerful device allows you to easily translate messages between MIL-STD-1553, ARINC-429, Ethernet, Serial and more, ensuring compatibility and reliability in your aerospace and defense systems.With its advanced features and user-friendly interface, our protocol converter is the perfect solution for aircraft manufacturers, avionics designers, and military system integrators. It offers accurate and efficient data transfer, making it ideal for use in a wide range of applications such as aircrafts, ground vehicles, and naval vessels.Our protocol converters, both rugged, to withstand harsh environments, and standard, for the lab, are fully customizable to meet your specific needs. Its compact and lightweight design makes it easy to install and integrate with other systems.Don't let communication protocol limitations hold you back - Upgrade your systems today and experience the difference!
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, up to 80 MS/s on 8 Channels
M2p.6568-x4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family.
-
Product
Frequency Converter
-
Our frequency converters, which we offer with outputs of up to 500 kVA, can be used to supply alternating current consumers with constant voltages that deviate from the input network.
-
Product
4-20mA Input A/D Converters
-
Analog Devices range of 4-20mA Input A/D Converters deliver accuracy, robustness and flexibility for Industrial Control applications. As the world’s leading supplier of data converters, Analog Devices is constantly introducing new A/D converters (ADCs) that drive system level architectures. Our portfolio of leading industrial 4-20mA Input A/D Converters offer considerable integration including, sense resistor, signal conditioning circuitry and advanced on-chip diagnostics to maximize performance and provide an integrated system level solution, all based upon robust silicon processes.
-
Product
Scalers / Converters
-
Converter/Scalers provide two essential functions. First, they convert the input signal from one format to another (e.g. analog VGA to digital HDMI). Second, they allow the user to select the resolution of the output signal for display on a flat screen display or projection system. In many cases the quality of the output signal from our Converter/Scalers will be better than what is possible using a direct input on the display because of the price/performance limitations of consumer scaling engines.
-
Product
Dual-Channel, Tri-Port Per Channel, for Extended Cabling up to 20 Meters
FW1
-
The FW1 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
Product
Compact Converters
-
Virginia Diodes offers compact converters (CCs) for frequency up and down-conversion. These converters are easy to use and well suited for high performance up and down conversion of wide band modulated millimeter-wave signals. VDI CCs offer full waveguide band coverage and are available from WR28 (22.5-40 GHz) to WR2.2 (330-500 GHz) with additional CCs under development. Compact converters can typically be delivered within 9-11 weeks ARO or less. Contact VDI for more information.
-
Product
Frequency to Current Converter
DAT4540R
-
The Frequency to Current converter DAT4540R is a signal conditioning din rail mount converter which converts a pulse input to an analog output equal to the set range which is selectable from 0.1 Hz up to 20 KHz. The DAT4540R also provides 2 relay outputs and a transistor output. The input can be from a Tacho, TTL, PNP transistor or from any Namur standard. The DAT4540R provides a Voltage or Current output that is isolated from the power supply and input.
-
Product
Modulation Distortion Up To 90 GHz
S930709B
-
S930709B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 90 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930709B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Converter Signal Amplifier – 4…20 mA – Wall Mounting
HD978TR5
-
Configurable converter signal amplifier with 4…20 mA (20…4mA).
-
Product
6-Channel VME Optical-to-Electrical Converter
V730
-
The V730 is a six-channel logic-level optical-to-electrical converter, packaged as a single-width, 6U VME module. When used with compatible Highland optical transmitter modules, the V730 provides fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
Product
Micro probes 1 MHz up to 6 GHz
MFA 01 set
-
The micro probes are used to measure magnetic fields and they have a high resolution. They measure magnetic fields up to 6 GHz, e.g. at signal conductors (150µm), SMD components (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the Bias tee BT 706. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee BT 706 to a spectrum analyzer or an oscilloscope. Langer EMV-Technik GmbH includes correction lines in the delivery. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
Product
Data & Protocol Converter
uMACC
-
The uMACC is a wholly contained Communications Converter (data converter - protocol converter or translator). Its small size makes it a complete solution for developing & testing both in the lab and in the field.The uMACC can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to Analog
-
Product
RF Signal Generators, Up to 6 GHz
SG380 Series
-
Stanford Research Systems, Inc.
The SG380 Series RF Signal Generators use a unique, innovative architecture (Rational Approximation Frequency Synthesis) to deliver ultra-high frequency resolution (1 µHz), excellent phase noise, and versatile modulation capabilities (AM, FM, ØM, pulse modulation and sweeps) at a fraction of the cost of competing designs.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
-
Product
Module To Convert A 5.25" Drive Bay To A Slim ODD And A 3.5" Drive Bay
9892200013E
-
Device Bay：5.25"Drive Fit：3.5" HDDColor：Black (4C2X)
-
Product
Signal Converters
-
The signal converters from HEIDENHAIN let you flexibly adapt the encoder signal interfaces to the requirements of your applications. For some applications, additional signals, such as from temperature sensors, are processed and forwarded to the subsequent electronics.
-
-
Product
DC/DC Converter 150 W
CQB150W-110S15
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 15 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
Product
Saluki S2108 Series Optical Network Tester (up to 45dB)
-
Saluki S2108 series Optical Network Tester is an intelligent high-precision optical network comprehensive tester with cloud wireless transmission, intelligent cloud platform and other functions. S2108 series adopts 7 inch capacitive touch screen, supports multi-point touch and integrates 18 functional modules internally. Compared to previous versions, it supports smart cloud platform, iONM, Multi-core measurement, 4G LTE SIM, GPS, Bluetooth and WIFI; built-in 8G storage capacity, can store more than 200,000 test data, and test data can be uploaded to the cloud wirelessly; PDF reports can be generated on the device and transmit them to the mobile terminal via WiFi & Bluetooth. S2108 series supports multi-tasks simultaneous operation, and VFL, OPM, LS functions can run in the background.
-
Product
Frequency Converter
A6
-
The Quartzlock model A6 frequency converter precisely changes either 5 or 10MHz sine wave signals to a number of other frequencies from 1Hz and 1pps upwards to other standard frequencies.
-
Product
32-CH 16-Bit Up to 250 kS/s Multi-Function DAQ Cards
PCI-9114 Series
Data Acquisition Module
ADLINK PCI-9114 series are 32-CH, 16-bit, high resolution multi-function DAQ Cards. The PCI-9114 device features flexible configurations on analog input. The devices are divided into 2 kinds: normal gain version and high gain version. Both versions provide 4 programmable input ranges for bipolar and unipolar inputs. The A/D on the PCI-9114DG device features a sampling rate of 100 kS/s with resolution at 16 bits, while PCI-9114A-DG/HG device features a sampling rate of up to 250kS/s with resolution at 16 bits. The device supports automatic analog input scanning, and offers a differential mode for 8-CH analog inputs and maximum noise elimination, as well as single-ended modes for 16- CH analog inputs. The PCI-9114 also features 1-CH 16-bit general purpose timer/counter, 16-CH TTL isolated digital inputs and 16-CH TTL isolated digital outputs. ADLINK PCI-9114 delivers cost-effective and reliable data acquisition capabilities and is ideal for a broad variety of applications.
