Back Planes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
Product
Multifunctional Data Acquisition Systems
MS1201
-
This system used for multi-purpose applications such as data acquisition and Automatic Test Equipment. ATE Computer has ISA Bus based eleven slots with inbuilt power supply. Micro Processor board or USB Controller is used to drive the back plane.
-
Product
Back Plane Tester
-
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
Product
80 Channel Relay Switch
DP-VXI-4503
-
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
-
Product
Qualification Hardware & Sockets
-
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
Product
Matrix
HLX
-
The HLX™ System is easy to configure to your exact requirements. It distributes HDTV signals up to 1,000 feet away to convenient zone receivers mounted wherever televisions are to be located. For audio systems, the HLX offers DSP and volume control per output (more about HLX for audio). Optional audio zone cards feed multi-channel amplifiers to distribute music to zones. Its robust back plane design allows up to 12 sources to distribute component video up to 1080p, along with analog stereo audio, digital coaxial audio, and digital optical audio. Four audio sources may be added, for a total of 16 source inputs. The new HLX offers a winning combination of performance, value, and unique features.
-
Product
Intel 80486 DX2 Processor Board
MS 1500
-
- PC 104 bus and ISA bus interface- Facilitates design of scalable architectural solution for Embedded System- Back plane eliminated by self-stacking PC 104 bus- Substantial reduction of development time, cost, as well as risk- Helps to Faster time-to-market / timely product productions- Used for LCA Simulation Project- Intel 80486DX2 @ 33MHz- 512Kbytes of STATIC RAM, 2048 Kbytes of FLASH PROMS- 64 Kbytes of DPRAM- External Interrupts- RS232 Serial Interface- Watchdog Timer- External Bus Interface
-
Product
ATE Computer
MS 1201
-
This system used for multi-purpose applications such as data acquisition and Automatic Test Equipment. ATE Computer has ISA Bus based eleven slots with inbuilt power supply. Micro Processor board or USB Controller is used to drive the back plane.
-
Product
USB BUS Controller Board
MS 1711
-
- 8 bit and 16 bit compatible Read and Write Cycles- Single or Block Memory and IO Write Cycles- Interrupt Cycle Generation- The generated bus cycles signals is compatible with ISA96 system back plane- External Reset- Double Euro Standard Board- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Industry Pack Carriers and Digital I/O
CPCI-4SIP-6U
Digital I/O
The CPCI-4SIP-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4SIP-6U is the perfect solution. There are four (4) Industry Pack sites providing up to 200 I/O pins accessible from either the front panel or the rear back plane.
-
Product
Control and Switch Modules
Mini Mux
-
Eclypse International Mini Mux Control and Switch Modules, plus Software Developer Kit (SDK) provides high density test circuit switching as a complement to the Eclypse Circuit Analyzers. The Mini Mux Switching gives the user the ability to test continuity and isolation in complex assemblies with thousands of circuit paths (such as avionic back planes and chassis), while minimizing the test equipment complexity and footprint.
-
Product
Signaling Control and Monitor Equipment
MS 1303
-
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
Product
Turning Mirror
10772A
Plane Mirror
The Keysight 10772A Turning Mirror is a 100% reflectance mirror that turns the direction of an incoming laser beam 90 degrees. The mirror is used in the 5530 Laser Calibration System for applications such as machine tool calibration. It can be used in place of the 10707A Beam Bender (6 mm or less beam diameter) for applications that require the larger aperture of the 10772A.
-
Product
Turning Mirror on Universal Mount
10769B
Plane Mirror
The Keysight 10769B Turning Mirror on Universal Mount deflects a laser beam at any angle, in either the vertical or the horizontal polarization plane of the beam. The 10769B contains the same turning mirror as the 10769A, but has a different mounting.
-
Product
Turning Mirror
10769A
Plane Mirror
The 10769A is ideal for use in laser measurement and calibration applications. In the calibration of slant bed lathes, for example, the beam steering mirror deflects the beam from the laser head upward, through the interferometer, along the lathe's cross slide. One or more mirrors can also create a path from a laser head to an interferometer located in an otherwise inaccessible position, as in the case of a milling machine with a table that moves in only one axis.
-
Product
Multi-Sensor In Plane
MS 1000-IP-20
-
Advanced Thermal Solutions, Inc.
The MS 1000-IP-20 is a three-sensor probe designed for measuring fluid velocity and temperature in the same vertical plane. It eliminates the need for multiple probes or a traversing probe for determining the flow profile or distribution.
-
Product
RF Planing & Optimization Software
Atoll
-
Atoll is a scalable and flexible multi-technology network design and optimisation platform that supports wireless operators throughout the network lifecycle, from initial design to densification and optimisation. Supports: GSM / GPRS / EDGE, UMTS / HSPA, CDMA2000 1xRTT/EV-DO, LTE, TD-SCDMA, WiMAX / BWA, Microwave links.
-
Product
High Voltage Inclined Plane And Erosion Tester
-
SCR ELEKTRONIKS have developed HIGH VOLTAGE INCLINED PLANE AND EROSION TESTER to carryout test specified in many standard to cover test method for the evaluation of the relative tracking and erosion resistance of insulating solid using liquid contaminant (ASTM D2303). Perform the Initial Tracking Voltage Test, Time to track Test, And Erosion Test as per selection.
-
Product
Back Pressure Tester
TU29P
-
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
Product
Back and Forth Scratching Tester
WGQ-60
-
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
Product
24" Front to Back Stiffeners
FB-24
-
Additional aluminum extruded front-to-back stiffeners are available for Vertical Cabinets. Includes installation hardware
-
Product
Push Back Probe VF416B180G10
1005149
-
The Push Back Probe VF416B180G10 (item number 1005149) is designed to verify that terminals are correctly locked in connector housings. VF416B180G10 can verify that a terminal remains securely locked in the connector housing and is not pushed back beyond the permitted position during contacting. For VF416B180G10, spring force is 1000 cN at a nominal travel of 5 mm. Pointing accuracy for VF416B180G10 is specified as ±0.1 mm. The electrical rating of VF416B180G10 combines 10 A continuous current with 30 mΩ typical contact resistance. For installation, VF416B180G10 uses an M2.5 x 0.35 thread.
-
Product
IEC60335-1 Electrical Inclined Plane Device
CX-100
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-1 Electrical Inclined Plane Device is designed and manufactured in accordance with IEC60335-1 clause 20.1. The IEC60335-1 Electrical Inclined Plane Device is to determine the stability of electric appliances which are used on a table or on the floor. The IEC60335-1 Electrical Inclined Plane Device consists of a surface and an angle adjusting device, with angles 0~15° adjustable.
-
Product
Back Pressure Test Kit
389
-
Thexton Manufacturing Company, Inc.
Aids in diagnosing clogged or restricted exhaust systems.
-
Product
Push Back Probes HVF100
1001837
-
The HVF100 Push Back Probes, designated with order code 1001837, are specifically designed to provide reliable and efficient connection capabilities in various electronic applications. With a total length of 50 mm, the probes feature a precise press ring diameter of 2.20 mm, ensuring compatibility with a wide range of receptacles and test equipment. The design's emphasis on compactness and durability makes it an essential tool for professionals seeking to optimize their connectivity solutions.
-
Product
Push Back Probes (VF3) VF383B0003G15
1005897
-
The Push Back Probes (VF3) VF383B0003G15 are expertly designed contact probes optimized for precision and reliability in various applications. With a pitch of 3.00 mm, they ensure smooth and effective connectivity within electronic circuits, capable of operating in extreme temperatures ranging from -45°C to +100°C. This model supports continuous current up to 8.00 A, maintaining a low typical contact resistance of just 30.00 mOhm, which is crucial for ensuring optimal performance and longevity.
-
Product
Push Back Probes (VF3) VF383B0002G15
1005896
-
The Push Back Probes (VF3) VF383B0002G15 is a high-precision contact probe designed for reliable performance in a variety of demanding environments. With a temperature range of -45°C to +100°C, this probe ensures that it can operate effectively under extreme conditions. Its robust construction features a beryllium copper plunger with gold plating, providing excellent conductivity and corrosion resistance. The brass barrel, also gold-plated, complements the design, ensuring durability and reliability during use.In terms of functionality, the VF3 probe boasts impressive specifications. The continuous current rating is 8.00 A with a typical contact resistance of just 30.00 mOhm, minimizing energy losses and enhancing efficiency. The mechanical specs of the probe include a preload of 300 cN and a spring force of 1500 cN, enabling the probe to maintain consistent contact under various pressures. With an impressive pointing accuracy of ±0.10 mm and a nominal travel of 5.00 mm, this probe is engineered for precision in measurement applications.
-
Product
Plane Mirror
10728A
Plane Mirror
The Keysight 10728A is a normal incidence plane mirror for beam diameters of 9 mm or less. It is a bare optic that requires a user-supplied mount. It is typically used with the 10735A and 10736A three axis interferometers.
-
Product
Push Back Probes (VF3) VF306B200G15S1
1004720
-
The VF306B200G15S1 Push Back Probe from the VF3 series is designed for precision and reliability in critical applications. With a pitch of 3.00 mm, it operates efficiently within a temperature range of -45°C to +100°C, making it ideal for demanding environments. This probe features a basic contact design, ensuring robust and consistent performance. Its significant preload of 1090 cN and a spring force of 1500 cN provide the necessary mechanical advantages for intricate tasks.
-
Product
Push Back Probes (VF4) HVF4
1001841
-
The Push Back Probes (VF4) HVF4, identified by Order code 1001841, are innovative components designed to enhance the functionality of electrical systems. With precise measurements of a total length of 34.00 mm, these probes are engineered with optimal performance in mind. The press ring diameter of 3.70 mm and outer diameter of 3.50 mm ensure a snug fit within various receptacles, while the collar height of 5.70 mm facilitates secure connections. This robust design caters to a variety of industrial applications, promising reliability and longevity in demanding environments.
-
Product
Push Back Probes (VF3) VF383B0007G15
1006292
-
The Push Back Probes (VF3) model VF383B0007G15 is meticulously engineered to deliver exceptional precision and reliability in various applications. With a pitch of just 3.00 mm, these basic contact probes are optimized for tight spaces, ensuring accurate measurements and connections. Designed to withstand extreme temperatures ranging from -45°C to +100°C, they are suitable for a wide range of environments, making them a versatile choice for both industrial and laboratory settings.
