Protection Relay Test
-
Product
Rear Cover, S6, Tabletop Configuration, For Part # 310 122 100
310113431
Protective Cover
The Rear Covers are designed to enclose the wiring that runs from the S6 Receiver on the tabletop to the instrument cards below. This rear cover is used with the S6 Receiver Part # 310 122 100.
-
Product
Semiconductor Relays
-
Panasonic Industrial Devices Sales Company of America
Panasonic Semiconductor Relays are categorized into two types: PhotoMOS® and Solid State Relays (SSRs).
-
Product
Computer Control 6-Phase Relay Protection Tester
GDJB-PC6
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1.This tester with standard 6 phase voltage, 6 phase current output,2.Voltage 125V/phase, current 30A/phase, 6 phases in parallel can up to 180A.3.Digital Signal Processor Microcomputer.4.Not only test the traditional relays and protectors, but also test the modern micro computer replays, special for transformer differential protection and transfer equipments.
-
Product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin D-type Connector
40-158-103
Relay
The 40/42-158-103 is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A. User connection is via a 50-pin D-type male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
PXI/PXIe Power Relay Module, 3xSP4T, 20 Amp
42-166-201
Relay
The 40/42-166-201 is a PXI/PXIe high density power relay module with 3xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
Receiver, I1, With Protective Cover
310128101
Receiver
i1 accepts a single iCon module and allows a variety of signal, power and coaxial connections. A protective cover is included with the receiver. Other accessories, such as keying pin kits and strain relief, are available.
-
Product
LXI Reed Relay Matrix - Dual 128x4 Plugin, No Direct Y Access, 6 Analog Buses
65-221-111
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 18 GHz, 50 Ω, SMA, Failsafe
42-780B-523
Relay
The 40-780B-523 (PXI) and 42-780B-523 (PXIe) are triple failsafe SPDT 18 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-780B-531-E
Relay
The 40-780B-531-E (PXI) and 42-780B-531-E (PXIe) are single failsafe SPDT 26.5 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Interactive Benchtop Test
test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
Diagnostic Relay Buddy 12/24 Test Kit
193
-
Relay Buddy 12/24 Pro Test Kit tests five different relays. Relay Buddy is a quick go / no-go tester for the most common automotive relays and this new version tests both 12 and 24 volt relays. . If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
Product
Protection Heads And Tubes
-
Choose from a wide variety of industrial protection heads and tubes to protect your temperature sensor probe from your rugged process application or surrounding environmental conditions.
-
Product
PXI 6xSPDT 16A Power EMR Module
40-161-102
Relay
This40-161 range of PXI power relay modules is available with achoice of 16 x SPST, 12 x SPST, 10 x SPST, 12 x SPDT and 6 x SPDT power relays, for switching loads up to 16A at250VAC. These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
Reed Relays
-
TPM Reed Relays - surface mount, high breakdown voltage, high temperature operate, high density, miniature PCB through hole, standard PCB through hole, EMF low thermal, high insulation/dry, high insulation/wet, high insulation/high voltage, DIP/dual in-line package, SIP/single in-line package, multiplexer, and more.
-
Product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
Test Module
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
Product
Customs & Border Protection Engineering Support
-
Scientific Research Corp. STI Division
SRC supports the Department of Homeland Security’s mission of protecting our country’s borders through the CBP’s airborne surveillance mission. We help the CBP to improve and maintain reliability of sensor, communications, and radar systems onboard the P3 aircraft.
-
-
Product
Residual Current Protection
-
Solutions to ensure the safety of people and installations against any ground currents. Available with ultra-immunized system as an essential solution to avoid financial losses due to outages caused by inadvertent trips. Specially designed to protect industrial installations in AC networks (type A), installations with both AC and DC components and DC-only installations (type B). Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
Product
Intrinsically Safe Relay
SSR-15
-
Model SSR-15 Intrinsically Safe Relay offers low power switching with solid state reliability and eliminates explosive conditions. Units are completely encapsulated and impervious to dust, moisture, or foreign material. Model SSR-15 can be mounted in any orientation and is shock and vibration resistant
-
Product
Scienlab Combined Battery Test Solution
SL1133A
test
Solution for testing battery cells with an output power up to ±3 kW and a voltage range up to 6 V.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Serial Controlled Relays And Relay Drivers
-
*ICS's Serial controlled Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Serial to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any Serial programming language. Use ICS's interactive Serial Keyboard program for easy operation from your PC without having to write a program.
-
Product
3-Phase Relay Testing System
TRES
-
With high power outputs packaged in an extremely compact and rugged system, the TRES has a tremendous power-to-weight ratio. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This hi-tech solution enables the testing of many different functions required in relay testing without the need of additional accessories.
-
Product
PXI/PXIe Power Relay Module,5 Amp, 50-pin D-type Connector
40-153-103-HI
Relay
The 40/42-153-103-HI is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
British Rail Relays
-
Mors Smitt manufacture the full range of British Rail equivalent relays including AC & DC coils, instantaneous, gold contacts, safety critical, push to test relay button, timer/time delay, and flashing.
-
Product
Relay Test System
-
Relay test products that combine a flexible hardware architecture with advanced test software. Relay tests can be constructed within minutes and displayed using a very simple interface, making the system ideal for low-cost production applications.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
Test System
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
Three-Phase Relay Test Equipment
AK-30
-
AC voltage source with 4 channels, current source and aux with 6 channels. DC source can be used simultaneously. Amplitude, frequency and phase angle can be adjusted respectively, independently and continuously; Control via PC via Ethernet RJ45 interface
-
Product
Relay I/O Modules
XTA Series
-
These modules are intended for use with BusWorks XT Series discrete I/O or other digital output modules for the purpose of driving high energy loads.
