Protection Relay Test
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
High Current Relay PXI Card
GX6115
The GX6115 is a 15 channel, high current relay board that plugs directly into any 3U PXI slot. The GX6115 also provides three transistor-driven channels for external relays. These outputs may be used to drive external loads, such as heavy duty relays, lamps or other devices.
-
product
PXI/PXIe High Density Reed Relay Module, 75xSPST
40-140B-121
The 40-140B-121 (PXI) and 42-140B-121 (PXIe) are 75xSPST general purpose switching modules. They are part of a range of high density relay modules using ruthenium reeds available in 50x, 75x and 100x Normally Open SPST configurations. Connections are made via a front panel 200-pin female connector.
-
product
PXI Quad Microwave SPDT Relay 26.5GHz 50 SMA
40-780A-534
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PXI Quad 4 to 1 RF MUX SMB 75 Ohm
40-832-004
The 40-832-004 is a 75 Ohm 4 to 1 RF MUX with 4 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
PXI/PXIe Microwave Relay, Triple SPDT, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-780B-533-E
The 40-780B-533-E (PXI) and 42-780B-533-E (PXIe) are triple failsafe SPDT 26.5 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
product
PXI Ultra High Density Reed Relay Matrix, 66x8, 1-Pole
40-541A-021
The 40-541A-021 is part of a range of ultra high density matrices. The 40-540A/541A/542A are the world’s highest density single slot PXI reed relay matrix modules and are available as a 132x4, 66x8 or 33x16 matrix with 1-pole switching.
-
product
Advanced SoC Test System
3680
The Chroma 3680 is an advanced SoC test system with data rate up to 1Gbps. The Chroma 3680 is capable of conducting parallel tests on multiple chips to meet the digital and analog IC testing requirements, with applications including MCU, digital audio, digital TV, set-top box, DSP, network processor, field programmable gate array (FPGA) and consumer electronics.
-
product
6TL08 Benchtop Test Platform
H710008
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
product
In-Circuit Test System Calibrations
Regular calibration is essential to ensure accuracy and reliability in testing. Forwessun offers precise calibration services tailored to your test systems, verifying that all components meet industry standards. Our calibration services maintain peak accuracy and compliance, so you can be confident in your system’s performance for any testing application. Choose from one-off calibrations or scheduled service contracts to meet your needs.- HP3070 - Agilent- Keysight - GenRad- Teradyne
-
product
In-Line RF Test Platform
AR925
This functional and RF test platform combines outstanding productivity with substantial equipment savings. The Faraday chamber of the fixture comes with an interchangeable cassette to minimize the testing cost of each new product
-
product
PXI/PXIe Microwave Relay, Triple SPDT, 40 GHz, 50 Ω, SMA-2.9, Remote Mount, Failsafe
42-780B-543-E
The 40-780B-543-E (PXI) and 42-780B-543-E (PXIe) are triple failsafe SPDT 40 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
product
PXI 32 x SPDT Reed Relay
40-110-121
Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
product
In-Circuit Test
TestStation LH
The TestStation LH in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne's popular, award winning TestStation product family. TestStation LH features SafeTest protection technologies for accurate, reliable, and safe testing of the latest low-voltage technologies.
-
product
In-Circuit Test System Rentals
Forwessun offers flexible test system rental options to meet short-term or seasonal testing demands. Our rental systems are rigorously tested for reliability and performance, giving you access to high-quality equipment without the need for a full purchase commitment. Customised rental agreements allow you to return the equipment when it’s no longer required, providing an ideal solution for scaling up production or filling in during periods of high demand.
-
product
Scienlab Battery Test System - Cell Level
SL1007A
The SL1007A Scienlab Battery Test System – Cell Level enables you to accurately and productively test battery cells for automotive and industrial applications. The bidirectional power supply charges and discharges your cells under test with very high efficiency.
-
product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
product
Off-Line Base Test Platform
6TL19
The 6TL19 is a bare half-rack with castors for creating Off-Line, modular, flexible, and reliable Base test platforms. The overall rack capacity is 11U (580mm depth).
-
product
Protective Cover, 75 Module, Receiver
310113352
The Receiver Protective Cover is available and encloses your modules and contacts when the ITA is not engaged.
-
product
PXI/PXIe Power Relay Module, 1xSP4T, 20 Amp
42-166-203
The 40/42-166-203 is a PXI/PXIe high density power relay module with 1xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
product
PXI 50 x Normally Closed Relay 1A 60W
40-145-001-NC
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
product
Protection Test Set
CMC 850
The CMC 850 is a protection test set dedicated to IEC 61850. It focuses on the real-time communication methods GOOSE and Sampled Values to interface with the devices under test.
-
product
Iridium Physical Layer Test Systems
PLTS
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
product
PXI Switch - 16-CH General-Purpose SPDT Relay Module
PXI-7901
ADLINK PXI-7901 is a general-purpose (GP) switch module implementing 16-CH independent single-pole double-throw (SPDT) relays (1 Form C). PXI-7901 can connect one input to one output and be used as signal switching and routing for measurement system or ATE. Thanks to its high switching capacity, PXI-7901 can also be used to turn on or turn off devices such as motors, fans, heaters, and lights. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7901, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
product
PXI/PXIe Microwave Relay, Triple SPDT, 26.5GHz, 50Ω, SMA, Remote Mount
40-780B-533-E
The 40-780B-533-E (PXI) and 42-780B-533-E (PXIe) are triple SPDT 26.5GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
product
PXI/PXIe Microwave Relay, Single SPDT, 40 GHz, 50 Ω, SMA-2.9, Internal Termination, Failsafe, Remote Mount
40-781A-421-E
The 40-781A-421-E (PXI) and 42-781A-421-E (PXIe) are single failsafe SPDT 40 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 50 GHz, 50 Ω, SMA-2.4, External Termination, Failsafe, Remote Mount
40-781A-722-E
The 40-781A-722-E (PXI) and 42-781A-722-E (PXIe) are dual failsafe SPDT 50 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
PCI 16xSPST 2Amp Relay Card
50-132-001
The 50-132-001 16xSPST relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin SGMC Connector
40-153-003
The 40/42-153-003 is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
PXI-2559, 2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module
778572-59
2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module - The PXI‑2559 is a general-purpose switch module featuring two independently terminated single‑pole double‑throw (SPDT) relays. You can use it to add flexibility to your video switch network or to maintain uniform signal paths across multiple channels when building high-channel-count multiplexers. The PXI‑2559 termination resistors minimize reflections on open channels and protect your source or device under test from damage. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.





























