Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
-
Product
Tape Up and Down Conversion Board
LS-37-P
-
The IF Digital processing board is a workhorse for all digital demodulation and combing. It can also support other unique functions like sub-carrier demodulation, FM/FM demodulation and tone receiving. Please consult the factory for your unique requirements.
-
Product
Low Voltage Testers
-
Device used to identify opens and shorts in applications that are driven on low voltages.
-
Product
Bit Error Ratio Testers
M8000 Series
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
Carry Case For Voltage / Continuity Testers
CP1190
-
Complete with belt loopSize: 290 x 75 x 45mm.
-
Product
Economy Combo Tester
780
-
The ACL 780 Economy Combo-Tester measures electrical resistance of wrist straps and heel grounders simultaneously and individually. This is a good alternative for companies seeking a personal auditing station but do not need to save data. Adjustable limits add versatility for ESD managers that may need to modify verification plans.
-
Product
Peel Force Tester
PT-55
-
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
Product
PC Based Tester
Cablescan L8
-
The Cablescan L8 provide the PC-based power of the larger PC based testers, but in an economical package for users who do not require more than 1024 test points. This analyzer is designed to operate under the control of your PC.
-
Product
Static Tester
-
Electrostate tester with LED indicator for the detection of static charge in the plus and minus range. An indispensable, inexpensive tool for the assessment and selection of materials in the living area, as well as the quality of the room climate.Buy Data Sheet
-
Product
Bottle Ramp Pressure Testers
-
Bottle Ramp Pressure (Burst) Tester is suitable for the internal pressure test of all kinds of beer bottles, wine bottles, beverage bottles, infusion bottles, antibiotic vials, etc.
-
Product
Downloadable PAT Tester
Apollo 500+
-
The Apollo 500+ features a comprehensive range of electrical safety tests with user configurable test sequences and checklists for PAT, PPM and PPE. It has storage for up to 10,000 test records and is compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
Product
Warm-Up Board
WECO 9000
-
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
Product
ATC Cabinet Switch Pack Tester
ASPT-5300
-
The ASPT-5300 ATC Cabinet Switch Pack Tester (HV) will run a series of comprehensive tests on the Model 2202-HV HDSP/FU. The Model 2202-HV HDSP/FU is an important component in the ATC Cabinet Monitoring System.The Model 2202-HV HDSP/FU not only provides field output drivers, but also monitors the voltage and current for each of the field outputs.
-
Product
Earth Ground Tester
-
Weshine Electric Manufacturing Co., Ltd
UT520 series can perform precise 3-wire and simple 2-wire earth resistance measurement for power and electrical systems, lightning protection equipment, and ground system of all electrical equipment.
-
Product
VME/VME64x Load Board
-
VECTOR Electronics and Technology, Inc.
The 6U VME and VME64x load board functions to test a system’s cooling capability by applying a variable load to the power supply for verification, then generating necessary heat to confirm the chassis’ cooling. This enables locating hot spots in the chassis so the airflow can be properly directed.
-
Product
Crease Recovery Tester
TF110
-
TESTEX Testing Equipment Systems Ltd.
Crease Recovery Tester, to determining recovery properties of fabrics by creasing in a loading device for a predetermined time using a weight suitable for the test method specified (BS/ISO/AATCC), After transferring the specimen to the clamp of the tester, the specimen is allowed to recover and the angle of recovery recorded. Fabric Crease Tester complies with ISO 2313, AATCC 66, BS EN 22313， etc.
-
Product
Data Acquisition I/O Boards
-
General Standards Corporation is a leading supplier in data acquisition I/O boards, provides a complete family of data acquisition cards for sonar, industrial, and embedded applications on several form factors/busses, and for many operating systems. Functions available include analog I/O, serial I/O, and high speed parallel I/O.
-
Product
Waterproof EC Tester Low with ATC
ECTestr Low
-
ECTestr Low tester series can measure natural water, verify reverse osmosis system operation and tap water quality. Check nutrient solution concentration in hydroponics applications.
-
Product
PCI FPGA Board
PCIe-8324-DSP
-
The Conduant PCIe-8324-DSP FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PCI Express interface and its two 12-lane HSS interfaces while performing complex calculations.
-
Product
Car Accessories Material Burning Tester
ZRS-4H
-
• Test Gas Source: Gas or Liquefied Petroleum Gas (Suggestion: Use good quality gas if possible) • Burner inner diameter: ￠9.5±0.5mm, about 100mm long with air adjusting hole • Height of flame: Can be adjusted from 20 mm to 100 mm according to the standard requirement • Applying time of flame: Burning time can be adjusted from 0 to 99 minutes 99 seconds • Test process: Automatic control • Inner volume: 0.05m³ • Material: Stainless steel or iron plate spray • Power: AC 220V; 50Hz/5A
-
Product
Loudspeaker Cable Testers
EMO E450
-
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
Product
Bench & Characterization Boards
-
Engineer, Design, Fabricate & Assemble Custom Boards for:*Device Characterization and Verification*Bench Testing*Failure Analysis*General Laboratory Use
-
Product
PCIe/104 OneBank FPGA I/O Board
EMC²-7A100
-
Sundance Multiprocessor Technology Ltd.
The EMC2-7A100 can use commercial, industrial or automotive graded Artix-7 FPGAs and is complimented with 1Gbyte of DDR3 local storage, 32Mbytes of Flash memory for storage/configurations and has 68x free differential I/O pins which are routed to a VITA57.1 FMC-LPC high-speed connector for bespoke interfaces.
-
-
Product
16 Relay Output Board
APCI-2200-16
-
*16 relay output channels*Switching voltage 60 V/DC, 48 V/AC, switching current 1 A*Optical isolation*Watchdog*Easy programming
-
Product
Digital Milliohm Meter and Resistance Tester
4338 mO
-
Standard Electric Works Co., Ltd
● Protection class: IP65 (Lid closed)● 4-Wire method for mΩ.● It's about 100mA at 1100.0mΩ range.● It's about 10mA at 11000mΩ range.● Measures down to 100µΩ (0.1mΩ).● Maximum resolution of 100µΩ.● Large LCD (68×34mm).● Relative mode. ● Data hold function.● MAX/MIN function.● Power source: 1.5V "C" battery × 8● Long battery life and stable power. ● Low battery indication.
-
Product
6U CPCI Switch Board
CP68302
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP68302 is compliant with PICMG CompactPCI specification. The switch board is largely applicable to high speed data switching and routing among boards and payloads at the internal of CPCI and ATR chassis. With standard 6U CPCI form factor, the Switch is compatible with ATR mechanical designs. CP68302 is designed with two heat-dissipating solutions: traditional air-cooling and ruggedized conduction- cooling with reliable anti-shock and anti-vibration performance, and excellent heat dissipation capability.
-
Product
Smart GPIB Serial Interface Board
Model 4806
-
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
Product
DMX Tester
DMXter4 RDM
-
The DMXter4 RDM takes the next step in protocol testing. It provides expanded DMX testing along with growing support for RDM testing and configuration. Who else would you trust to support the new standard? The DMXter4 is simple to use. Eight buttons run its menu-driven software. The DMXter4 uses a back lit 40-character display. Some functions can drive a PC using the USB port. Software updates are done via the USB port.
-
Product
Stand Alone Low Voltage Tester
TestMate 256
-
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
