Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
Product
Tachometer Tester
Series 1921
-
The Model 1921 Tachometer Tester is used for the testing and calibration of electrical and mechanical tachometer generators and indicators.
-
Product
Fatigue Failure Tester
EKT-2002FF
-
EKT-2002FF Flexing Fatigue Tester is designed in accordance with ASTM D4482 to test the fatigue life under a tensile strain cycle on different kinds of vulcanized rubber compound to determine the fatigue life at various extension ratios.
-
Product
PowerNet Tester
-
The PowerNet Tester (BNT) is designed to test batteries, ultracaps and all other types of electrochemical power sources for 14 V and 42 V power net systems. Designed to test vehicle system batteries for 14V and 42V power net systems. But they may also be used for testing all other types of electrochemical power sources just by setting the required current and voltage values.
-
Product
Digital RCD Tester
1612 EL
-
Standard Electric Works Co., Ltd
●Microprocessor-controlled●Extra large LCD (78 × 67mm)●Very low power consumption●50Hz and 60Hz operation●Accurate digital readout of disconnection time●Over temperature protection●Over voltage protection●Fuse protection●Zero crossing circuitry permits testing at 0° or 180°●Auto power off●Backlight function●Wiring polarity indicator●Measures voltage between Line and Earth before testing●Frequency measurement indication
-
Product
Pin Brinell Tester
-
Newage Testing Instruments, Inc.
The Pin Brinell is a cost effective instrument, which uses a calibrated shear pin to control the amount of load applied. Provides consistent loading regardless of operator. Tests in 100 - 730 equivalent Brinell range.
-
-
Product
Large Bare Fiber Spools
-
*Custom lengths to 60km of optical fiber*Designed to fit spools in the most efficient manner*Portable for easy handling and protection*Organizes fiber while ensuring performance
-
Product
Comparison Testers
GCL Series
-
Nagman Instruments & Electronics Pvt. Ltd
Budget Solutions. Very Low Maintenance Cost. Compact & Easy to carry for Lab & Field use. Priming Pump with Fine Adjustment Vernier Incremental Pressure generation. Adjustable Foot.
-
-
Product
Beating Pulp Tester
DRK116
-
Shandong Drick Instruments Co., Ltd.
DRK116 Beating Pulp Tester is applied to test the filter ability of suspending pulp liquid. That is to say the determination of the beating degree. Product features According the inverse proportion relation between beating degree and draining velocity of suspending pulp liquid, designed as Schopper-Riegler beating degree tester.DRK116 Beating Pulp Tester is applied to test filterability of suspending pulp liquid and research fiber condition and evaluate beating degree.
-
Product
Hipot Testers
Hypot® Series
-
The Hypot Series sets the standard for safety and efficiency in production line Hipot Testing. Whether your application requires AC Withstand tests, DC Withstand tests, or Insulation Resistance tests, The Hypot Series provides innovations that will allow you to begin achieving best practices for safety and efficiency without the need for an expensive automated test system or connection to a PC. You can even connect the Hypot Series with the HYAMP Series to form a seamless safety compliance system for Hipot and Ground Bond Testing.
-
Product
Battery Testers
-
Memory & Read FunctionRight Device to know the TRUE -LIFE of Battery Capacity (Resistive / Voltage) Simultaneously MeasureOn - Line Testing without shutting down batteryBuilt - in Comparator FunctionRates Conditions as PASS, WARNING or FAILDatalogging Memory FunctionCompact and lightweightRS-232 Interface & SoftwareAuto Power Off
-
Product
Cable Testers
E448
-
The EMO cable testers are designed for use in portable and bench mounted applications, including the assembly and testing of cables.
-
Product
HDBaseT Tester
-
The MS-TestPro is the only HDBaseT tester that is all-inclusive, 100% reliable, portable and affordable, making it an indispensable tool for all installers and integrators. It provides AV professionals with all the information that they need while in the field to enable them to verify the integrity and stability of every system tested down to the last detail. Moreover, the MS-TestPro generates a report including all the parameters necessary to certify link quality and status up to 4K Ultra High Definition. The report can then be transferred to a computer or even to a smartphone for use by both installer and end-user.
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
Tachometer Testers
-
Compact, lightweight and quiet tachometer tester designed specifically for calibrating and troubleshooting aircraft and helicopter tachometer indicators and generator/alternator systems on the flight line in the workshop.
-
Product
BMP-1-S Board Marker Probe
BMP-1-S
ICT/FCT Probe
Current Rating (Amps): .05Voltage Rating (VDC): 15Recommended Duty Cycle: 1 sec. On (min.), 5 sec. OffTest Center (mil): 1,000Test Center (mm): 25.40Full Travel (mil): 62Full Travel (mm): 1.57Recommended Travel (mil): 50Recommended Travel (mm): 1.27Full Marker Travel (mil): 62Full Marker Travel (mm): 1.57Direction of Rotation: CCWScribed Diameter (mil): 50Scribed Diameter (mm): 1.27Rec. Mounting Hole Size (mil): 468Rec. Mounting Hole Size (mm): 11.89Recommended Drill Size: 15/32 (in) or 11.90 mm
-
Product
Electronic Toy Tester
-
Programmable ultra high resistance tester is used to test the high resistance of different kinds of material.
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710-5V-I
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
Evaluation boards
-
iSYSTEM evaluation and development systems are optimized for evaluation of the featuring microcontroller whether it fits the project requirements or for the development of the target application while the hardware is still in the design stage. Our systems are distinguished by high speed debug and trace connection to experience the full microcontroller capabilities.
-
Product
Salinity Testers
-
Labodam pocket salinity testers are equipped with platinum sensors, providing fast and reliable results measuring the salinity of water and other low and high salt concentrated solutions. Equipped with replaceable electrodes, helping to reduce maintenance cost.
-
Product
Transistor Tester
-
*Measure rich DC parameters of maniford semiconductors, e.g. diode, transistor, controlled silicon, FET.*Measure capacitor, varistor, DC voltage signal source*Measure 78 and 79 three terminal voltage regulator*Data hold, low battery warning*Complete with carry case and six 1.5V AA batteries
-
Product
Electric Testers
-
ATEQ offers a broad range of electric testers designed to meet the diverse needs of various industries. These testers, including advanced battery testers, are pivotal in ensuring the efficiency and safety of electrical systems. They are used in applications ranging from automotive and e-mobility to broader industrial purposes and EV battery testing. ATEQ’s electric testers are known for their precision, featuring integrated databases for battery types and parameters, secure systems with comprehensive battery protections, and user-friendly interfaces. This makes them essential tools in production lines, research and development laboratories, and for EV/HEV expertise
-
Product
Torque Tester
NDI-800CN/80CN
-
Ideal for daily inspection of electric screwdrivers. Enhanced visibility, ease of use, and ease of connection. The easy-to-read color display, addition of a clock function, and simple operation with dedicated software enable more advanced management. Efficient measurement without unwinding work by "OW joint".
-
Product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
-
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
Product
SpaceWire RMAP Tester
121
-
The SpaceWire RMAP Tester is a software test platform that provides the means to validate SpaceWire RMAP target implementations and to test the generic functionality of any unit that relies on the RMAP protocol for its configuration and control.
-
Product
Packaging Compression Tester
-
It is very important to evaluate compressive resistance of packaging material before its selection for maintaining product shape, quality while its transportation, distribution and handling in bulk.
-
Product
Analog Expansion Board
MSXB 014
-
The MSXB 014 Analog Expansion Board provides 4 additional analog outputs. Up to 16 Analog Output Expansion Boards can be connected to a single DAP for a total of 64 additional output channels.
-
Product
Automatic Current Tester
77069
-
For the rapid safe and accurate testing of DC current on 12v vehicles. The tool plugs straight into the vehicles fuse board and displays the current on the large LCD display. Specification range 0-48volt max 20 amps, 12v battery included.
