Automation
-
Product
Decoking System
-
Discover how our hydraulic decoking systems have transformed hydraulic decoking into an increasingly reliable, efficient and automated process.
-
Product
HMM+™ Tester
Model 4702
-
The Model 4702 HMM+™ is a completely new tester primarily intended for device level testing and produces a current waveform as specified in the IEC-61000-4-2, from a 50 ohm source impedance system.*This tester provides device level test data that allows users to evaluate the IEC current waveform protection level of their devices. We included failure identification by leakage current increases in the 4702 tester so precise pass/failure levels can be closely measured.*The 4702 HMM+™ provides a new and improved test connection method for making quantifiable and repeatable device level HMM measurements.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Product
Automated Pressure Calibration System
4322
-
The Fluke Calibration 4322 Automated Pressure Calibration System enables almost any user to calibrate almost any pressure gauge, transducer, transmitter or switch, including vacuum, compound, absolute and high-pressure devices. It provides high-end, laboratory-grade performance across a very wide range, on the bench or in situ.
-
Product
Automatic Wire Test Set
AWTS
-
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
Product
PCI-6289, 32 AI (18-Bit, 625 kS/s), 4 AO (2.8 MS/s), 48 DIO PCI Multifunction I/O Device
779111-01
Multifunction I/O
32 AI (18-Bit, 625 kS/s), 4 AO (2.8 MS/s), 48 DIO PCI Multifunction I/O Device - The PCI‑6289 offers analog I/O, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI/cPCI Modules
-
As a leading provider of PXI products in Asia’s test & measurement market, ADLINK has devoted its extensive field experience to the PXI platform. After more than ten years and developing more than 100 PXI products for automation and testing, and as a sponsor member of the PXI System Alliance, ADLINK continues to expand PXI and PXI Express offerings with innovative products, meeting the unique needs of high-speed and high-bandwidth applications, such as spectral monitoring and signal intelligence.
-
Product
Control and Monitoring of Machines
Millenium 3
-
Easy to program and to implement, it enables the control and monitoring of machines and automation installations with up to 50 I/O. It is positioned right at the heart of the Crouzet Automation range.
-
Product
EV/HEV Battery Pack Environmental Exerciser/Monitor System
-
DMC designed, built, and programmed a set of automated test stands for charging and discharging electric vehicle battery packs. The test stands also monitor the performance of these battery packs while exposed to harsh environmental...
-
Product
COM Express Type 6 Basic Module With Intel® Xeon® And 6th Gen Intel® Core™ I7/i5/i3 Processor, Intel® CM236/QM170/HM170
CEM500
-
The CEM500, a COM Express Type 6 basic module, is based on the 14 nm Intel® Xeon® processor E3-1505M v5 and 6th generation Intel® Core™ i7/i5/i3 processor (codename: Skylake-H) with Intel® CM236/QM170/HM170 chipset. The outstanding Intel® Gen 9 HD Graphics enables the CEM500 driving multiple 4K displays without the need of a discrete graphics card. Two DDR4-2133 SO-DIMM supporting up to 32 GB system memory capacity and four SATA-600 with RAID 0, 1, 5, and 10 are available. Additionally, the rugged COM Express computer-on-module Type 6 supports an industrial operating temperature range of -40°C to 85°C for applications in extreme harsh environment. With its full solid, outstanding computing performance and low power consumption design, the CEM500 is targeted at telecommunication, medical imaging, digital signage, gaming machines, military, human machine interface, industrial automation controllers and IIoT applications.
-
Product
Automation Control
-
ACE universal damping solutions convert kinetic energy in to heat. This makes machines faster, quieter, more durable, lighter and therefore more competitive and profitable.
-
Product
Electromagnetic Compatibility (EMC) Testing Capabilities
-
Electromagnetic Compatibility testing analyzes the ability of electronic devices to operate as anticipated when in proximity to other electronic devices or in the presence of electromagnetic disturbances that interfere with their intended operation.We help you ensure EMC compliance and attain the needed EMC certifications by assisting you in maximizing accuracy, reducing testing cycles, and getting your products to market faster — from design conception to end-product completion even against the most demanding electromagnetic regulations.We understand that time to market is everything which is why our global testing capabilities and custom testing solutions utilize the latest technology and automation software, helping you meet demanding time-to-market needs. Our streamlined testing process brings your product from development to end use efficiently in accordance with government, regulatory, military, or industry standards based on your compliance needs.
-
Product
Forensics Test & Analytical Solutions
-
Science and technology are playing an increasing role in the investigation and prosecution of crime. Technology innovation, automation, databases and good laboratory practices are essential to the pursuit of justice and are critical to the appropriate collection, assessment, and application of evidence in the criminal justice system. Forensic Toxicology, Antidoping, Forensic DNA Analysis, Controlled Substances, Trace Evidence Detection, Suspicious Documents, LIMS for Forensics Labs, Forensics Resource Library, Human Identification.
-
Product
Test System
Tessy
-
TESSY automates the whole unit test cycle including regression testing for your embedded software in C/C++ on different target systems. As an easy-to-install and easy to operate testing tool TESSY guides you through the unit test workflow from the project setup through the test design and execution to the result analysis and reporting. TESSY takes additionally care of the complete test organization as well as the test management, including requirements, coverage measurement, and traceability.
-
Product
Log Periodic Antennas
-
Log Periodic antennas allow quick sweep measurements without a band break. This feature makes it convenient to use the Log Periodic antenna with a automated emissions or immunity measurement system. The size of the antenna also allows it to be used in a small area like a shield room.
-
Product
DC Power Supply
62000H Series
DC Power Supply
The 62000H Series includes 14 different models ranging from 5KW to 15KW, with current range up to 375A and voltage range up to 1000V. The 62000H can easily parallel up to ten units capable of 150KW with current sharing for bulk power applications, for example, battery bank simulation of 450V/150A/67.5KW for electric vehicle and military use. There are 100 user programmable input status on the front panel for automated test application and life cycle ON/OFF test. In addition, the 62000H has a 16 bit digital control with bright vacuum fluorescent display readout. The 62000H series DC power supplies are very easy to operate either from the front panel keypad or from the remote controller via USB / RS232 / RS485 / APG (Standard) and GPIB & Ethernet (optional). Its compact size with 3U only can be stacked on a bench in a standard rack without any difficulty.
-
Product
USB4 Version 2.0 Receiver Compliance Test Software
N5991U42A
-
N5991U42A is the receiver compliance test automation software, allowing you to test and characterize USB4 Version 2.0 PAM3 designs.
-
Product
Drone Inspection Software
Qii.AI
-
Qii.AI automates the detection and analysis of defects. It is the only enterprise AI platform that combines drone inspection software with an AI labeling tool, AI-assisted computer vision, and machine learning.
-
Product
Structured Wiring
-
Structured wiring refers to a whole-house network of audio, video, data, telephone, television, home automation or security signals. This wiring can be installed when a home is being built. It may be put in during a remodel. Structured wiring can also be added on its own.
-
Product
Rubber Testers
-
TA Instruments introduces a complete line of new instruments for the measurement of rheological and physical properties of polymers, rubber and rubber compounds at all stages of manufacture. The new rubber testing instruments include a Rubber Process Analyzer, Moving Die Rheometer, Mooney Viscometer, Automated Density Tester and Automated Hardness Tester.
-
Product
PID Controller
ZET 7190-R
-
ZET 7190-R — PID controller on CAN bus. It is used in automated systems for control signal forming.
-
Product
Metrology Device
XPLOR 100
-
XPLOR 100 is a state of the art, fully automated metrology device designed for measurement and analysis of bubbles and inclusions for optical substrates in the Visible and NIR wave-bands.
-
Product
USB-6349, 32 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785816-01
Multifunction I/O
32 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6349 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6349 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Electronic Loads
T3EL Series
-
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
Product
Performance Audio Analyzer
U8903B
Audio Analyzer
Measure your most demanding audio devices with higher accuracy and a low residual distortion of -110 dB See the real performance of your devices with the highest resolution audio measurements available Automate testing with built-in test sequences Meet standards more easily with pre-configured POLQA and PESQ measurements Simultaneously measure/view up to eight channels on a single screen in real time Configure for specific applications with digital audio interface (AES3/SPDIF and DSI) and Bluetooth audio measurements options
-
Product
Power Assembly Tools
-
In order to keep up with modern production demands, you need tools that are faster, smarter, more accurate, and more powerful than ever before. Mountz answers that demand from the heart of Silicon Valley with a full line of innovative electric and pneumatic power tools and automation systems. With intuitive Mountz tool controllers, complex multi-pass assemblies become simple and your production speed will skyrocket. Quality control and regulatory compliance can be streamlined with real-time error proofing and time stamped documentation. From the simplest repairs to the most technical manufacturing projects and everything in between, Mountz power tools stand out from the crowd.
-
Product
HT High Temperature Kinematic Viscometer
miniAV®-HT
-
miniAV®-HT is a fully automated, single-sample, benchtop viscometer for determining the kinematic viscosity of asphalts at 60 °C and 135 °C. The Ubbelohde-style tube covers a 100-fold viscosity range at values between 0.5 mm²/s (cSt) and 10,000 mm²/s (cSt).
-
Product
SparkFun Atmospheric Sensor Breakout
BME280 (with Headers)
-
The SparkFun BME280 Atmospheric Sensor Breakout with Headers is the easy way to measure barometric pressure, humidity, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
-
Product
Floor-Standing 3D Optical Profilometers
-
High-precision, non-contact metrology systems designed for rapid, automated, large-area surface characterization in industrial and R&D settings.
-
Product
PathWave BenchVue Universal Counter App
BV0011B
-
Easily control your counters with PathWave BenchVue universal counter software app to build automated tests, visualize measurements, and log/export data.
-
Product
Software Development Kit
Verisurf SDK
-
Available free with all version after Verisurf 2017 – the Verisurf Software Development Kit (or “SDK”) provides a flexible programming environment specifically designed for creating customized dimensional metrology applications that enable manufacturing automation.
