Electrical Fast Transient
-
Product
Battery & Electrical System Testing
12-0200
-
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
Product
Multifunction Electrical Installations Meter
MPI-525
-
Possible measurementsShort-circuit loop measurement:*impedance measurement with 23 A current (44 A phase-to-phase) - short-circuit resistor R=10,*measurement range: 95...440 V, frequency 45...65 Hz,Short-circuit loop measurement with resolution 0,01, in distribution network without tiggering RCD (In30 mA):*automatic calculation of short-circuit, detection of phase voltage and phase-to-phase voltage,*additional UNI-Schuko plug for automatic measurement, AGT adapter for 3 phase network measurement.Testing of general and selective RCD with the rated differential current of 10,30,100,300,500 and 1000 mA. (Type AC, A and B).Measurement of insulation resistance:*with test voltage 250 V, 500 V, 1000 V, 2500 V,*measurement range up to 10G,*automatic discharging after measurement,*automatic measurement of all resistences in 3,4,5-wire cables using optional adapter AUTO-ISO,*acoustic signals in 5 sec intervals for insulation resistance characteristic,*elapsing T1, T2, T3 times (0...600 s) form measurement of absorption coefficients (DAR, PI or Ab1, Ab2)*safety measurement - protection against overvoltage.Measurement of earthing resistance.Bi-directional testing of PE wire continuity using 200 mA current.*Autocalibration of test leads.
-
Product
Field-installation Type Electric Conductivity Meter (Four-Wire Transmission, For Low-concentration)
HE-200C
-
HE-200 connects conductivity sensor (ESH/FS Series) and measures conductivity and temperature in the sample water. It is suitable for monitoring pure water/boiler water drainage recovery control and inline measurement of pharmaceutical water conductivity according to USP<645> quality guidelines.
-
Product
Electrical DfT & Fault Coverage Analyzer
TestWay
-
TestWay's electrical DfT analyzer enables designers to validate designs at the schematic capture stage, to ensure that adequate measures have been included to comply with the manufacturers test requirements. The ability to verify that PCB designs have been developed with adequate Design-for-Test in mind, is key in determining the most effective test strategies and accurately calculating fault coverage, which is crucial in improving competitive advantage, lowering cost and ensuring product quality.
-
Product
2D/3D Electrical CAD Software
-
SEE Electrical is an easy-to-use Electrical CAD software to efficiently create electrical schematics and wiring. With SEE Electrical, you can quickly produce conceptual diagrams and generate assembly drawings, strips, and cable lists.
-
Product
HandyScope HS6-DIFF With SafeGround: 100 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-100XMG-W5
-
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
Product
Electrical Probe Systems
-
INSTEC's Probe Systems offer an integrated solution for performing component-level electrical measurements over a wide temperature range.Compact Mini Probe Stages enable an existing inspection microscope or optical test setup to be converted easily into a precision temperature-controlled semiconductor testing and qualification station.Analytical probe stations are fully featured industry-standard platforms for all modern probing applications and testing.Benchtop Probe Stations provide the user with four independent electrical probes with X,Y,Z micropositioning for precise placement without opening the sample chamber.Highly configurable probe systems meet a range of requirements for atmospheric and temperature control, sample areas, and electrical measurements.
-
Product
Electrical Safety Test Scanner
19200
-
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
Product
Electrical Insulation Tester Kit with Dual Display
420001
-
When undertaking power installations, the 420001-insulation tester can provide special help to test wiring. This unit can provide 125V,250V, 500V and 1000V source for the test, and under each range it can supply 1mA current to feed the capacitance load. With the auto-range function, it can measure up to 4,000 Megaohm with the resolution of 1Kohm.
-
Product
Electrical Safety Testers
STW-9900 Series
-
* 500VA AC Test Capacity* 240 x 64 Ice Blue Dot Matrix LCD* Manual/Auto Mode* Function Key for Quick Selecting* High Intensity Flash for Caution & Status Indication* Safety Interlock Function* Zero Crossing Turn-on Operation* Zero Crossing Turn-on Operation* True RMS Current Measurement * High Resolution : 1μA for Measuring Current, 2V for Setting Voltage* PWM Switching Amplifier to Enhance the Power Efficiency and Reliable Testing* Max. 100 Memory Block for Test Condition (Step) Setting. And Each Step can be Named Individually* Remote Terminal on the Front Panel for“Start”and“Stop” Control by External* Interface: RS-232C, USB Devise, Signal I/O and GP-IB (Option: OPT.1)
-
Product
HD-Series Automation Electric Screwdrivers
-
The HD-Series automation electric screwdrivers operate with only the HDC controllers. The HD-Series electric screwdrivers feature a high performance brushless motor design that provides durability and reduces the common maintenance costs associated brush type electric screwdrivers. These brushless electric torque screwdrivers are engineered for automation assembly applications that provide manufactures with a rapid, reliable and precise method of fastening screws. The technology of these automation tools provide tighter process control and higher quality standards, while keeping costs down. The patented HD-Series hybrid torque control system is the world's first torque tool using both air and electric power to set and control torque.
-
Product
Electric Insulating Oil Tester
PortaTest
-
Portatesters are easy to use. Based on the test standard, you select the corresponding test sequence. Then, the required test probe and the electrode gap for the selected test standard is displayed. The setting gauge, included in the scope of delivery, facilitates the adjustment of the electrode gap. Afterwards you fill the insulating oil in the test vessel and close the test chamber.
-
Product
Fast Recovery Diodes
-
We offer high-performance products with low forward voltage (VF) and high-speed reverse recovery time (trr) for increasing device efficiency.
-
Product
Ultra Fast Flexible Implantable Microprobe
IT-23
-
IT-23 Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Time constant 0.005 seconds. Tissue Implantable with a 23 gauge needle (supplied). Fairly fragile. Sensor wires are twisted TFE Teflon™ insulated. Maximum Temperature 150°C. Isolated. Probe diameter .011", 3 foot lead.
-
Product
Electric Servo Motor Type Tension and Compression Tester
-
It is a tensile / compression fatigue / durability / performance tester for various materials and automotive parts that have an ultra low inertia AC servomotor mounted on the actuator.
-
Product
Electric Vehicle Supply Equipment ATS (EVSE ATS)
-
It is a customized system based on Chroma 8000 ATS specializing inverification of EV Supply Equipment (EVSE) and complying with SAE-J1772 in programming the test items for operation.
-
Product
Phase Angle and Power Factor Transducer of Single-phase AC Electric Power
NMTFi
-
The NMTFi device is a phase angle and power factor transducer operated in single-phase power network and featuring two independent analogous outputs. The A output measures the phase angle between voltage and current, the B output measures the power factor. In such a was one single NMFTi transducer is able to replace two customary transducers thus making it possible to achieve significant savings in installation space.
-
Product
Testing of Electrical Safety
-
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
Product
Electrical Impedance Tomography
-
Electrical Impedance Tomography (EIT) is an imaging technique that visualizes conductivity or impedance distributions both in 2D and in 3D. Sciospec is partnering with world leading scientists in the field to deliver solutions that enable using EIT both in research and in practical applications.
-
Product
PCIe Fast Digital Waveform Acquisition/Pattern Generator - 32 Digital I/O Channels, 1 kS/s up to 125 MS/s Sampling Speed
M2P.7515-X4
Digital Waveform
The M2p.75xx series of fast digital I/O cards allow to acquire or replay digital patterns with a programmable speed of up to 125 MS/s. The direction can be switched by software between input (digital data acquisition) and output (digital pattern generation). The on-board memory of 1 GByte can be completely used for digital pattern. Furthermore the on-board memory can be switched to a FIFO buffer allowing to continuously stream data in either output or input direction.
-
Product
Electric Motor Dynamometer
-
Dynamometer consists of aggressively designed rotor technology that allows for higher torque without the need for multiple rotors. Thus not only does the WB Series unit offer more pack to the punch, but the inertia of the WB Series unit stays well below the inertia of the engine being load-tested.
-
Product
Handyprobe HP3: 100 MS/s, 50MHz BW, 1MS Single-channel Differential USB Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HP3-100XMPS-W5
-
The TiePie engineering Handyprobe HP3 is the world's first PC based 100 MS/s differential USB oscilloscope.
-
Product
High Power Programmable AC Source With Transients
-
Chroma Systems Solutions, Inc.
Ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification to quality assurance and mass production
-
Product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
-
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Product
HandyScope HS6-DIFF With SureConnect: 200 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-200XMS-W5
-
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
Product
Fast Precision D/A Converters
-
For test and measurement, and HIL applications demanding both dc and ac performance, our fast precision D/A converters (DACs) enable higher speed waveform generation of up to 12.5 MSPS with 4 × oversampling with clean signal spectrums.
-
Product
Electric Motor Checker
CIE/1001
-
Cambridge Instruments & Engineering Co.
Housed in attractive wooden body with sunmica finish. For comprehensive check of Rotor and Stator Inductance, Resistance and Insulation Resistance without dismantling the Motor. Only to isolate the power supply.
-
Product
Electric Servomotor Steering Durability / Performance Tester
-
Power steering This is an electric servomotor fatigue / endurance tester intended to conduct forward and reverse durability tests of racks and pins.
-
Product
Electric Safety Wall Detection Test Mode
-
AllWin Instrument Science and Technology Co., Ltd.
Electric safety wall detecting functionTest mode programmableACW to IR function toggle automatically
-
Product
Deep-Level Transient Spectroscopy System
FT 1030
-
The Deep-Level Transient Spectroscopy has grown up to a most powerful tool for semiconductor characterization with unbeaten sensitivity in trap concentration detection and high efficiancy in impurity parameter determination.
