Fiber End Face
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 2m, 45º
A1604F5-C-0A200
Cable Assembly
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
-
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
Product
Power, Patchcord, ITA, 36", Mini Power, 16 AWG White Teflon, Single Ended
7-244916000-036
Power Patchcord
Power, Patchcord, ITA, 36", Mini Power, 16 AWG White Teflon, Single Ended.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends
A068SMR-T-5A100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
Mini OTDR Fiber Optic Reflectometer with VFL OPM Laser Source
MT-1300 Plus
-
Guangzhou Wanglu Communications Co., Ltd.
- Display: 3.5 inch color TFT-LCD screen- Handheld design, light weight and easy operation- Single mode: 1310/1550 nm- Dynamic range: 24 / 22dB (can test about 60 km)- Automatic measurement mode: 1310/1550 nm dual wavelength can be tested simultaneously- Applicable fiber: SM- <8m extra-short event dead zone- Wavelength: 1550nm- Up to 24dB High Dynamic Range- Distance Range: 4,8,16,32,64,128,256km- Pulse width: 3ns-10us- RJ45 cable TDR test & cable sequence test- Optical power meter, Visual fault locator, Laser source- Event Map, can display the length of the link, the type of event point and the position of break point.- USB interfaces, supporting USB stick and printer and direct cable download to PC via ActiveSync- LED light- Built-in friendly-environment lith ium battery with high capacity for over 12 hours of operating life
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends
A050DF4-C-0A100
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable 100-Pin Micro-D Male to Unterminated, Tinned Ends, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-T-9A200
Cable Assembly
This 2m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Tinned Ends, 16A, 0.5m
A020GFR-T-1B050
Cable Assembly
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, SC/PC Connectors, With Interlock
42-852A-218-HI
Multiplexer Module
The 40/42-852A-218-HI is a PXI/PXIe 8-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Optical Fiber Identifier
TW3306
-
Techwin(China) Industry Co., Ltd
Optical Fiber Identifier TW3306Ais an essential installation and maintenance instrument. By inserting the fiber into its adapter head, it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.
-
Product
Signal Patchcord, ITA, Mini Power, 50u Gold, 36", 14 AWG White Teflon, Single Ended, (40 Amps)
7-239912000-036
Signal Patchcord
Signal Patchcord, ITA, Mini Power, 50u Gold, 36", 14 AWG White Teflon, Single Ended, (40 Amps)
-
Product
Fiber Optic Components For Optoelectronic Packaging
-
OZ Optics offers a wide range of standard and custom fiber optic components for optoelectronic packaging. Components include collimators, focusers, patchcords, connectors, and metalized fiber. The low backreflection collimators and focusers are available for a wide range of industry-standard connectors and wavelengths. The hermetically sealable patchcords, with glass or metal solder, and metalized fiber meet high Telcordia standards. The polarization maintaining patchcords and connectors use our specially designed ferrules that minimize insertion loss, backlash, and rotational errors.
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. With a simple firmware/software upgrade, a single function board can become a full function board without having to purchase new hardware.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated to Tinned Ends, 1 Amp, 2m length, 500 Port
A500RMR-T-1B200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to to products using the 500-Pin SEARAY connector.
-
Product
Optical Fiber Splicing Tool Kit
SAT-02B
-
Shaanxi Aitelong Technology Co., Ltd
SAT-02B Tool kit is wonderful for optical fiber fusion splicing. It includes the most frequently required tools for preparation and cleaning optical fibers before cleaving and splicing. And well fits to Aitelong model SAT-17S and SAT-17M fusion splicers.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5941-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Fiber Shaker
MPX-SR3
-
Arden’s MPX Modal Explorer makes measurement of Encircled Flux easy, and accurate, and it complies with international standards. But if you are measuring laser-based transmission light sources for multimode systems you may need to use a test jumper assembly and fiber shaker in order to avoid “speckle”. Industry standards (for example IEEE 802.3aq and FOTP– 203) call for the use of a mechanical fiber shaker.
-
Product
Cable Assembly, 96 Pin Female SCSI (Spring Latch), to 96 Pin Female SCSI, Double Ended, 36"
515109008
Cable Assembly
Cable Assembly, 96 Pin Female SCSI (Spring Latch), to 96 Pin Female SCSI, Double Ended, 36"
-
Product
Cable 100-Pin Micro-D Male to Unterminated, Tinned Ends, 0.5m 2-56 UNC Screwlocks, Metal Shell
A100SMR-T-9A050
Cable Assembly
This 0.5m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
Product
Signal, Patchcord, ITA, TriPaddle, 36", 26 AWG White, Single Ended (1.5 Amps)
7-105926000-036
Signal Patchcord
Signal, Patchcord, ITA, TriPaddle, 36", 26 AWG White, Single Ended (1.5 Amps)
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors, With Interlock
42-852A-118-HI
Multiplexer Module
The 40/42-852A-118-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
51-Pin REDEL High Voltage Cable Assembly, Male to Unterminated, Cut Ends, 0.25A, 1m
A051KMR-C-HA100
Cable Assembly
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with cut ends constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips are provided to secure the connector to associated product.
-
Product
Micro Coax, Patchcord, ITA, 50 Ohm, 36", RG316 Tan, Single Ended
7-361116000-036
Coax Patchcord
Micro Coax, Patchcord, ITA, 50 Ohm, 36", RG316 Tan, Single Ended.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends
A068SFR-T-6A100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Fiber Optic Light Source
-
Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 2m, Screwlocks
A068SMR-C-6B200
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends
A050DM5-T-0A100
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly 78-Pin D-Type, Male to Unterminated With Tinned Ends
A078HM5-T-0A100
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products.
-
Product
3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end
GT97107
-
3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
