Dark Field
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Field Test
-
Field test equipment is an optimised solution for large system testing, which, thanks to its distributed architecture, enables the placement of several small-sized testing systems.
-
Product
Field Intensity Meter
LM870-W
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Trunk-line AC voltage, V/A, C/N and TILT measurable* Automatic over-voltage shut-off protection* AC/DC optional (Ni-H/Li storage battery inside)* Full-digital key-board operation, direct freq. & channel input* Automatic scanning, Automatic channel-filtering, Automatic error-operation amending* All standard channels and subjoin channels pre-set inside* New channel-table setting according to user's special requirement* Spectrum displaying* English/Chinese operation interface* Audio output (speaker set-in)
-
Product
Single Axis AC Magnetic Field Sensor
MGC-1A
-
Macintyre Electronic Design Associa
The MGC-1A is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1A amplitude response is insensitive to the frequency of the field over its 30 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Damped Oscillatory Magnetic Field Immunity Tester
DOMF61000-10
-
DOMF61000-10 damped oscillatory magnetic field immunity test system included damped oscillating wave generator and single ring coil, it’s designed for to do damping oscillation magnetic field immunity test and fully meet IEC 61000-4-10, EN61000-4-10 and GB/T 17626.10 standards requirement.
-
Product
RF Near Field Probe Set DC to 9GHz
-
EMF & RF close field sniffer-set for use with any Spectrum Analyzer or Measurement Receiver. The EMC Near Field probe set allows for straightforward pinpointing and measurement of interference sources in electronic component groups as well as execution and monitoring of generic EMC measurement. Our RF near field probe set is especially suitable for: - Pinpointing interference sources - Estimation of interference field strength - Verification of shielding and filtering measures - Identifying faulty components - Detecting circuitry overly sensitive to interference.
-
Product
Relative RF Field Strength Meter
7601
-
Coaxial Dynamics Model 7601 Relative Field Strength Meter is used for measuring the relative strengths of radiating fields of patterns from a transmitting antenna system, making relative RF power measurements, or peaking and adjusting fixed or portable transceivers and antennas
-
Product
Full Range / High Resolution Field Portable NIRSpectroradiometers For Remote Sensing
-
SPECTRAL EVOLUTION is a leading manufacturer of field-portable and laboratory NIR spectroradiometers and spectrometers for remote sensing applications including geological remote sensing, ground-truthing, spectral remote sensing, environmental and climate research, crop and soil research, vegetative studies, forestry and canopy studies, radiometric calibration transfer, upwelling and downwelling measurement and more. Our NIR spectrometers and spectroradiometers provide the best combination of high resolution and high sensitivity resulting in the most precise field portable instruments available on the market.
-
Product
Active Loop Antennas / Magnetic Field Probes
-
Is an active, shielded handheld loop antenna with nearly con- stant antenna factor over the entire frequency range. It can be used for testing according to CISPR, MIL, FCC, EN, ISO, ANSI, ETSI and many other standards.
-
Product
Field Ttesters
-
Our product range comprises from small handheld, battery fed testers to full featured service performance assurance tools and distributed monitoring systems. We have several product lines including:QoS / SLA verification system Ethernet, IP, Critical Data, VoIP, IPTV .Hand-held testers: Gigabit Ethernet, Synchronous Ethernet, E1, PDH, SDH, Ethernet, IP, Jitter, Wander, Datacom, Frame Relay, etc.
-
Product
Near Field Probes 30 MHz up to 6 GHz
XF1 set
-
The XF1 set of near field probes consists of 4 passive near field probes and one passive E field probe for making measurements in the development phase of the magnetic and electric fields in ranges from 30 MHz to 6 GHz. Due to their integrated impendance matching, the probes are less sensitive in the lower frequency range than the RF type probes. The probe heads of the XF1 set allow for the step by step identification of interference sources of the magnetic field on an electronic assembly. At first, for example the XF-R 400-1 detects the fields which the assembly emits in total. Next, using higher resolution probes the interference sources can be more precisely detected. The E field probe is used for the detection of electric interfering fields near the assemblies. With trained use of the near field probes, field orientation and field distribution can be detected. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Rotation Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Direction indicators are indispensable for use in the electrical assembly of three-phase motors. In normal use, the test leads are connected to the live terminals, with an R / L display showing the later direction of rotation of the electric motor. In addition, this model can be used for the contactless determination of the direction of rotation of switched-off or not connected motors. Place the switched-on measuring device on the motor parallel to the longitudinal axis without test leads. Now turn the shaft of the motor, the measuring device now shows a right or left movement.
-
Product
Near Field Microprobe E-field 7 MHz to 3 GHz
ICR E150
-
The near field microprobe is used to measure electric fields at extremely high resolution and sensitivity. The optimal distance to the object being measured is < 1 mm. Due to its small probe head dimension, the probe has to be moved by a manual or automatic positioning system, e.g. Langer-Scanner.
-
Product
Single Axis AC Magnetic Field Sensor
MGC-1
-
Macintyre Electronic Design Associa
The MGC-1 is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1 amplitude response is insensitive to the frequency of the field over its 5 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
On-Site Field Testing & Evaluation
-
MET is a highly-regarded resource for electrical inspection agencies within the United States and Canada to assure compliance of unlabeled equipment in the field. Field evaluations are performed by MET Laboratories on unlisted equipment to support the Authority Having Jurisdiction.
-
Product
Field Meter
AP01 FULL HD
-
The AP01 FULL-HD is a field meter with full coverage of the terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
Product
Prototype Performance Field Testing iOS app
-
Centric's new Field Testing app provides an innovative solution for product performance feedback. Centric's Field Testing App is an example of how capturing data live, in the moment, is not only incredibly valuable but also a natural way of working. This app helps reducing costs while also improving product innovation and performance; which are ultimately keystones of great brands.
-
Product
Compact Inverted Microscope, 1mm Field Of View
-
Viewing transparent samples from below in a Petri dish, flask, well plate or cavity slide. The microscope is compact and can be put inside most incubators to view experiments without opening the door. Time-lapse images can be saved and viewed remotely.Ideal for use as a Bench Microscope in teaching applications.
-
Product
Ruggedized Field Deployable Tester
PUMA
-
- 18-slot PXI / 4-slot SCXI Chassis- 1.2 GHz Embedded Controller- 4-axis Motion Controller/Simulation- 8-port RS-232 Serial Module- 4-port RS-485 Serial Module- 48 bit Isolated Digital I/O- Reconfigurable multi-function I/O FPGA Module- 5 1/2 digit DMM- 200 MHz 2-channel Scope/Digitizer- Multi-function Data Acquisition (DAQ)- 8-channel Analog Input Module- 6-channel Analog Output Module- General Purpose Switching- RF suite (optional)
-
Product
EMF/ RF Field Strength Meter
-
Designed for measuring and monitoring Radio–Frequency electromagnetic field strength.
-
Product
Probes, Magnetic Field
EM-6880 | 9 KHz – 520 KHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
New Generation Analyzer for IPTV Field Servic
NetProbe 2000 IPTV
-
New Generation Analyzer for IPTV Field Service The NetProbe 2000 IPTV is the newest, state-of-the-art handheld analyzer on the market for field testing of IPTV customer services. It can monitor up to 40mbps of IPTV traffic and emulate a Set-top box.
-
Product
Medium Wave Field Strength Meter, 520 kHz to 5.1 MHz
PI 4100
-
The PI-4100 was designed to become the successor to the industry standard FIM- 41 and to provide the accuracy and reliability that the international engineering community, government regulators, and broadcast licensees have depended on for more than a generation.
-
Product
Electrical Tester Grid Field
-
TCI can furnish grid spring probes for most Bare Board Electrical Testers in production at most Printed Circuit Board Manufactures. Look for your model of Bare Board Tester in the following list and call TCI for current price quotation.
-
Product
RF Field Probes (LSprobe)
Immunity
-
Your product descThe LSProbe range of laser-powered E-Field probes offers precision, speed, and flexibility for EMC testing environments that demand reliable, uninterrupted measurements. These compact, battery-free probes use a galvanically insulated laser power supply, eliminating downtime and enabling continuous, high-resolution field monitoring with minimal noise and fast pulse response.ription goes here.
-
Product
Field Testing
-
Electronic force measuring device with digital display in MN / m², switchable for load plate.
-
Product
3D/2.5D Time-Domain Electromagnetic Field Solver Software
EM-CORE ®
-
3D/2.5D Time-Domain Electromagnetic Field Solver Software for Planar-Circuit and Antenna Simulation. 3D & 2D Radiation Patterns Modeling, Spiral Inductors Modeling, 3D EM Modeling of Filters, Intuitive Geometry Build, and more!
-
Product
Relay / Magnetic Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
Product
Broadband Isotropic Field Strength Probes
PI-01, PI-01E, PI-03, PI-05
-
Modern design probes meeting the requirements of most EMC and RF safety standards for RF safety, industrial, military and radar communication applications: 0.2-1000 V/m, 10 KHz-40 GHz.
