Circuit
-
Product
Test Points
TestStation LX2
-
TestStation LX2 is Teradyne's largest pin count in-circuit test system. Configurable up to 15,360 pins, TestStation LX2 utilizes the new UltraPin II 128HD pin card for testing large, complex, and heavily-integrated printed circuit board assemblies.
-
Product
Metal Cored PCB
-
Teledyne Labtech is at the forefront of complex metal-cored PCB design and manufacture. The PCB use a thin metal core <2 mm, which acts as isolation between the RF/Microwave circuit and the Analogue/Digital circuitry and creates an excellent thermal path.The major advantages are reduced size and no need for complex microwave feed-thru's. The ability to laser cut pockets allows the designer engineer to mount the high power MMIC directly on to the metal core.
-
Product
Broadband Detectors
-
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
Product
Analogue (1kV below) Insulation Tester
8031 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 2Ω & 20Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
Product
RV Protocol Trailer Light and Electric Brake System Tester
RVCHECK
-
The RVCHECK is a fast, easy, low-cost way to test RV lighting and electric braking systems. In addition to powering an RV trailer's lighting circuits for easy checking, your RVCHECK measures the current draw of the electric brake coils, and checks the break-away battery circuit.
-
Product
Single Front Slot Universal Low-Profile PCI To PCMCIA Adapter, External
P314B
-
To cater to the latest generation of low-profile PCs that can only use low-profile PCI add-in boards, Elan has created the P314. This model, from the P-Series range, features a PCMCIA Type III 3.5" drive bay mounted slot and a circuit board that conforms to the MD1 profile specification. It will allow you to use any TypeI/II/III PCMCIA card.
-
Product
Voltage References
-
Renesas' wide selection of voltage reference (Vref) circuits offer accurate and stable reference voltages unaffected by external influences such as variation in temperature, input voltage and time.
-
Product
Rack Mount Cable Tester
AudioJog Rack
-
There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. The LED's also show the possibility of high resistance or leakage connections.
-
Product
250 MHz Passive Probe for HDO4000, 10:1, 10 MOhm
PP017-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
RTD Simulator PCI Card 6-Channel PT1000
50-262-102
Simulator
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card can provides a setting resolution of <90mΩ (also available in <8mΩ - PT100) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
Portable Analog Instruments
-
Instrument transformer is a general term for voltage transformers and current transformers that are used with electrical instruments. The main purpose of instrument transformers is to extend the measurement range for electrical quantities (voltage, current, power, power factor) on large-current and high-voltage circuits. They serve to convert currents and voltages to levels that are suitable for measurement, and to insulate the instrument, etc. from high-voltage circuitry.
-
Product
Digital Electrical Network Analyzer
1826 NA
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. No need to add all the bonding points and connection paths resistances.● Displays voltage supply at the transformer (Line to Neutral), without loading the transformer. Displays voltage between Line (Phase) and Earth (Ground), without drawing any current.● Measures the impedance of the line itself so you can analyze and differentiate between the multiples paths of the wiring.● Measures the Neutral Impedance. Single one smart push button operation; ON, Test, Scroll trough results and menus.● Checks wiring integrity (LEDs).● Auto off/auto ranging (software ranging). ● Combined prospective short circuit current, loop, individual wire and Earth Tester.● Voltage test L-N and L-E.● Loop test for L-E and L-N and PSC.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for large orders.
-
Product
Versatile RF Network Analyzers for LF and MF
TE3000-series
-
The TE3000-series of RF vector network analyzers have full vector measurement capability, and accurately resolves the resistive, capacitive and inductive components of a load. The user can display the vector impedance plus a range of related parameters including SWR, reflection coefficient, return loss and R-L-C equivalent circuit.
-
Product
PXI RTD Simulator Module, 12 Channel, PT500
40-263-302
Simulator
The 40-263-302 is a 12-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
AC/DC Clamp Milliammeter (CE)
M-730
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current*Suitable for measurement of 4-20mA DC controlled circuit*DC mV analog signal output*Lowest influence from Magnetization and Terrestrial magnetism*Wide measuring ranges - up to DC 1000mA and AC10A*Sleeping current measurements for automotive electronics circuit*Jaw opening capability 30mmφ
-
Product
Flex Test Fixtures
-
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
Product
50MHz USB Pen-Style Frequency/Period Counter
USBcount50
-
USBcount50 is a new concept in USB Frequency Counter products. PC based frequency counters deliver many user benefits including flexibility, ease of use and economy. They are an invaluable tool during design and debug of digital circuits and can be used to quickly to verify generated frequencies, pulse widths and duty cycles .
-
Product
Voltage Meter
MN6SV
-
The M-module is intended for use as part of an automated measuring system for monitoring any object, the output signal of which is high voltage, for example, telemetry circuits, etc.
-
Product
Electrical Circuit Protection - Fuses
-
Eaton is a world leader in the design and manufacture of Bussmann series fuses and Eaton medium voltage power fuses.
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
6-12V Heavy Duty Circuit Tester
1650
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. Use on accessories including lights, starters, alternators, cooling and heating components, radios and relays.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
MTM-Load-1: 1-Channel DC Load Module
-
LEAN AND MINIATURIZED PRODUCTION TESTING: With its ultra-small footprint, the MTM-Load-1 is engineered for load-testing of battery chargers, amplifiers, USB power outputs, and motor driver circuits. Ideal for functional testing in production or validation test environments.
-
Product
Transforming Analog Circuit Breaker Testers
MAC-21
-
The MAC-21 uses proven microprocessor and A/D converter technology to provide real-time waveform analysis. This ensures accurate true-RMS readings of current pulses, even with DC offset and distortion, which are typical in primary injection testing. Intelligent threshold algorithms provide accurate trip time measurement. Integration of measurement and control functions allow advanced features such as preset on times, auto ranging, and optional printer or computer interface.
-
Product
Clamshell Type Mechanical Fixtures
Series 10
-
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
-
Product
Test Analyzer
ST2303
-
Shenzhen Star Instrument Co., Ltd.
The ST2303 three-phase energy meter field test analyzer reaches accuracy class 0.05. It generates stable signals by using ARM and digital signal processing technologies. Its highlights include compactness, light weight and portability. Various supply options, including measuring circuit, external AC power supply and internal lithium battery are offered.
-
Product
Chip Resistor Networks/Arrays
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s Chip Resistor Arrays are offered in cases from 0201 to 0805. The smaller 0201 case sizes are available with flat terminations and all other case sizes are offered with either convex or concave terminations. The EXB Series Resistor Arrays are available in 2, 4, or 8 Resistors per package. These Resistor Arrays allow for an improvement of the placement efficiency. Compliance Standards include: IEC 60115-9, JIS C 5201-9, EIAJ RC-2129, AEC-Q200 and RoHS.Panasonic’s Resistor Networks are available in 8 or 15 bussed Resistors and are recommended for all pull up/down circuits.
-
Product
PXIe-4163, 24-Channel, ±24 V, 50 mA PXI Source Measure Unit
784483-01
Analog Input Module
PXIe, 24-Channel, ±24 V, 50 mA PXI Source Measure Unit—The PXIe-4163 is a high-density source measure unit (SMU). It features 4-quadrant operation with a current resolution of 100 pA and the ability to sample up to 100 kS/s. The module also offers the ability to maximize stability and measurement accuracy with SourceAdapt, which allows you to custom-tune the transient response to match the characteristics of any load. The PXI-4163 is ideal for a broad range of mixed-signal integrated circuits (ICs) in semiconductor production test.
-
Product
Test & Test Development for Circuit Card Assembly
-
Teledyne Advanced Electronic Solutions performs comprehensive testing at the CCA and system level assembly. Teledyne AES can perform testing developed by the customer or develop a complete test strategy for the customer’s products.- Bed of Nails FixtureIn-Circuit Test (Bed of Nails) or Flying Probe Testing for rapid feedback on CCAs- Functional testing of CCAs or complete systems- Environmental testing to include vibration, thermal cycling, HASS, etc.- CCA and system level test development- High frequency testing – currently to 40 GHz- High power system testing – currently to 4kW
-
Product
Safe Isolation & Lockout Tagout
-
Our range of Safe Isolation Kits and and our NEW lockout devices for isolating circuit breakers, RCD's and MCCB's, enable you to work safely on installations, following the safe isolation procedure, without the risk of electric shock. All our devices and equipment are easy to use and all equipment is supplied with Lockout Tags to identify the device is locked and who to contact in the event of an emergency.
