Electricity Monitors
Measure the consumption of electricity.
-
Product
Level Monitoring
-
Magnetic level switches are used for the monitoring and control of liquid level in tanks. These level switches are specifically manufactured to customer specifications. The float switches are manufactured with a hermetically sealed contact which is located within the guide tube. The float sliding on the tube contains a ring magnet which activates the sealed contact in a non-contacting fashion. The sealed contacts are available as SPST (N/O or N/C) or SPDT (N/O + N/C). The float sliding up and down on the guide tube is the only moving part on the M-series magnetic float switches.
-
Product
Remote Monitor Management Information Base
SNMP RMON MIB
-
For every control table in the MIB, create and delete rows with various combinations of SNMP requests (all variables in a single request throughall variables in individual requests).Determine which row of this table is modeling the ethernet interface connected to the agent (requires that we are using ethernet). Check that this is for the same interface discovered in the "interfaces" test. Check counters.Build a history control row pointing to the interface connected to the agent. Check validity and traffic reported.Test agent's ability to generate an alarm on an RMON variable, then on threshold condition. Test for support of alarms on failing events, and in the event of target variable vanishing.Set up agent to track hosts on the ethernet interface connected to the agent. Check that entry was added for Rmon device's own ethernet address.Generate various top N reports (hostTopN test) and check validity.Start a matrix capture and check that the src-dst and dst-src tables are in sync.Check a channel and check for event generation (filter test).Create a channel and start a capture. Test locking and wrapWhenFull operation.
-
Product
Snap-on RF Current Monitoring Probe
TBCP2-250
-
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
Product
Continuous Emission Monitoring System
CEMS
-
CEMS, the “Environmental Eye” for Source Emissions.A Continuous Emission Monitoring System (CEMS) is an integrated system to measure fuel flow, dust, and concentrations of air pollutants such as SO2, NOx, CO, CO2, THC and O2 in accordance with the applicable regulations for the emission source.
-
Product
Oxygen Deficiency Monitors
-
Oxygen deficiency monitors are critical anywhere low oxygen levels in normal air can happen. If oxygen levels continuously drop eventually the room air simply cannot support life. This is a very dangerous situation.
-
Product
Electric Vehicle AC Charging Compatibility ATS
8000
-
It is a customized system for Electric Vehicle AC Charging Compatibility testing.Hardware : Integrated by AC Source/Power Meter/DC Source/Function Generator/Scope/ EVSE CP & PD Simulator…。Software : Fully complies with SAE-J1772, CNS15511 test requirements
-
Product
Electric Servo Motor Type 1 Axis Vibration Tester
-
In Addition, The System Configuration Requires At Least 3 Main Units, A Control Panel, And A Controller, And Does Not Require Hydraulic Units Or Blowers. The Exciter Can Perform Standard Tests And Performance Tests Required For Automobile Seats Based On An Electric Servomotor Type Multi-Axis Vibration Tester.
-
Product
LE Photoacoustic Infrared Refrigerant Monitor
Chillgard LE
-
The Chillgard LE Photoacoustic Infrared Refrigerant Monitor is specifically designed for reliable detection of some of the most common refrigerants from up to four remote locations—with a minimum detection level of 20 ppm.
-
Product
Optical / Electrical Clock Recovery
N1078A
Clock and Data Recovery Unit
N1078A Optical/Electrical Clock Recovery provides standards-compliant clock recovery capabilities for single-mode optical as well as electrical signals from 125 MBd up to 64 GBd PAM4 and NRZ
-
Product
Flow Monitor
B2900
-
Blancett B2900 flow monitor offers advanced digital signal processing technology in an easy-to-access package. Enclosed in a spacious polycarbonate NEMA 4X housing, the electronics are located on a single board, designed for straightforward and convenient field installation. The B2900 enclosure features an LCD display with push button programming as well as a pre-drilled hole for external wiring connections, such as Modbus RTU and other outputs.
-
Product
Vibration Monitoring
-
Acu-Vib Electronics Acoustic & Vibration
Building & Ground Vibration Monitoring Station.
-
-
-
Product
Ohm-Stat Guardian Pro Constant Monitor
-
Tests two people and two wriststrapsLED and buzzerNIST calibration includedWorks with all single wire capacitance wrist strapsAll cords suppliedCE markCan be calibratedProduct conforms to the ESD S.20.20 spec standards110v AC powerGround dock included
-
Product
Area/process radiation monitoring
-
Monitors gamma and beta rays/ neutron with high accuracy and reliability. *Each monitor is controlled with central control system and alarm is given when the measurement exceeds alarm level. Area monitors and dust monitors.
-
Product
Mill & Silo Monitoring System
MSM-100
-
MSM-100 is a monitoring system specifically designed to continuously detect carbon monoxide(CO) in pulverizing mills. The high level of CO produced by any incomplete combustion process, is used by the MSM-100 system as advance warning of a mill fire. It is suitable for any coal or peat system where advance warning of spontaneous combustion is required. MSM-100 is intended for operation in the electricity, metals, cement, steel and processing industries.
-
Product
On-Line Electric Motor Analyzer
EMAX
-
We understand that shutting down electric motors for testing can be time consuming and costly. With the EMAX technology you can now test a motor while it is operating with no interruption to production. Within seconds the EMAX will provide a comprehensive detailed look at the Power Circuit, Power Quality, Stator, Rotor, and Air Gap.
-
Product
Transformer Monitors
-
The Transformer Advantage is a precision temperature monitor for liquid-immersed power and distribution transformers. It is rugged, fully electronic and field configurable. With Transformer Advantage, users can extend transformer life, utilize maximum capacity and reduce maintenance costs.
-
Product
Area Monitor
ND-4000
-
Portable, battery powered, whole area monitor with warning light and audible alarm.
-
Product
Electric Transformer
-
Zhengzhou SMS Electric Co.,Ltd
For the convenience of the user or the low voltage metering box of electric energy metering, instrument with high precision (0.1)split core type current transformer.
-
Product
Charge Plate Monitors
-
Our charge plate monitors the voltage of the battery and the voltage of the battery.
-
Product
In-Service Electrical Continuity Test Card
Cisco ONS 15454
-
The Cisco ONS 15454 In-service Electrical Continuity Test Card is a solution for confirming proper DS-1 and DS-3/EC-1 cabling between the Cisco ONS 15454 shelf assembly electrical interface adapter (EIA) panels and the user's patch panels. The solution is designed for shelf installations that are presently carrying traffic and tests for common wiring errors including electrical shorts, opens, wrong connections, and tip/ring reversals.
-
Product
Resistivity Monitor / Controllers
750 Series II Resistivity Monitor & Controllers
-
The unique circuitry of the 750 Series II Resistivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
Product
Electrical Button Life Span Tester
IEC60884
-
Shenzhen Autostrong Instrument Co., Ltd.
Plugs and the sockets life tester is designed according to the corresponding provisions of the GB2099-96,GB16915-97 and IEC60884-1,used to detect the mechanical life test of the household and similar purposes of the plugs and the sockets products.
-
Product
PDS Cutter Dredger Monitoring Software
-
TELEDYNE PDS for Cutter Dredges is designed to the requirements of the dredge operator to carry out their job more efficiently. The operator has a real time overview of the dredger with the top and side views displaying the vessel outline, ladder, and cutter head along with the surveyed depths, design, and dredged depth.
-
Product
30/50 GHz Dual Electrical Channel DCA-M
N1094A
Oscilloscope
The N1094 DCA-M builds on that legacy by using the high-performance elements of 86100 and electrical channel hardware of N104X plug-in modules. Electrical channels are available with 30 GHz and 50 GHz bandwidths.
-
Product
Permanent Noise Monitoring System
831-NMS
-
The Model 831-NMS permanent noise monitoring system is designed for long term monitoring around airports, industrial facilities, motorsport complexes, wind farms, mining operations, and within the general community. Many required accessories are integrated through the INT docking station. Two way remote communication is available for monitoring and control from a central station. Larson Davis provides the hardware, software and open interface to allow this system to be customized for any application or purpose.
-
Product
NIBP Simulator for Testing Patient Monitors
SECULIFE BP PRO
-
The SECULIFE | BPPRO is the high-end product from the new range of NIBP simulators and is distinguished by a great variety of functions. It includes functions such as NIBP, IBP, ECG, temperature, arrhythmia, respiration, leak detection and much more. Specially developed to cover a great diversity of functions and nevertheless to ensure a compact design, the SECULIFE | BPPRO fulfills the requirements of modern medical technology. It makes no compromises with regard to functionality and input diversity. There's hardly another product with a similarly large range of features.
-
Product
C/Ku Band Satellite Monitoring
SCL-3412
-
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
Product
Portable Electricity Meter Testers
EE-120A-3S + EE-500V-3
-
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. All types of electricity meters – mechanical or electronic, for active, reactive or apparent energy, single-phase or three-phase – can be tested with the Energy Standard. The following meter tests can be carried out with the EE Test System: Error Test, Register Test, No Load Test and Starting Current Test. Full analysis of the customer load can also be performed, if current clamps have been ordered. All test results ( maximum 3 Test Plans, 5 Manual Measurements and Customer Load Analysis) can be saved in one file. 100 saved files can be viewed on the LCD display or transferred to a PC via USB port.
