Jumpers
-
Product
Pin-Line™ Vertisocket™
Series 0517
-
Pin-Line Vertisockets. For mounting components, jumpers, etc., at right angle to PC board. Available 1 to 25 positions; cuttable to any number desired.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Media Converter, 100Mbps, Multimode 1310nm, 2km, SC
EKI-2541M
-
Provides 1 x 10/100 Mbps Ethernet port with RJ45 connectorProvides 1 x 100 Mbps Multi-mode SC type fiber portProvides internal jumper for Link Fault Pass-through (LFP) settingSupports full/half duplex flow controlSupports store and forward transmissionSupports auto-negotiationSupports MDI/MDI-X auto crossoverSupports redundant 12-48 VDC power inputProvides flexible mounting: DIN-rail and Panel mount
-
Product
Length Network Cable Tester
SC-8108
-
1. Measure network cable length and determine the distance of breakage point.2. Check wiring error in 5E, 6E, coaxial cable, such as open circuit,short circuit, jumper wire, reverse connection .3. Portable unit with long battery life (wait-case 50 hours).4. Automatically time-delay shut off.5. Self-checking and automatically compensate any change in battery capacity or ambient temperature.
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Four Channel Low-Noise DC Bias Card
PI-41702
-
The PI-41702 is a four channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V, and this card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output. Additionally there is a ‘D’ type connector that allows the introduction of laboratory type supplies to reduce the noise further. To change from using the internal power supplies to external power supplies requires repositioning jumpers. The PI-41702 also has voltage and current sense for remote measurement of the voltage and current levels.
-
Product
37 Pin Breakout Interface
VSI-Breakout-37
-
The VSI-Breakout-37 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Screw-Terminal & Power Adapter Board - DC-coaxial-jack connectivity for 1 or 2 External VDC Power Supplies
TE3202
-
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
Product
Switch Modules - 32 Two Pole Relays Arranged as Four Separate 8x1 Multiplexers
JX32/4(1x8)-2A
-
This module has 32 two pole relays arranged as four separate 8x1 multiplexers as shown in the figure. The muxes may be operated and wired individually for up to 64 8x1's per chassis, or jumpered together to form 16x1's or 32x1's or jumpered to the backplane to form up to a 512x1 mux or two 256x1 muxes. It is available with Type A, Armature relays only.
-
Product
68 Pin Breakout Interface
VSI-Breakout-68
-
The VSI-Breakout-68 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
LAN Cable Multifunction Tester
TCT-2690PRO
-
LAN/length cable tester quickly and accurately tests network, telecommunication, cable and security systems for a variety of issues. Tests for open or short circuits, jumpers, cross or split pairs, continuity and wiring of cable patterns, cable identification and length measurement using included remote ID.
-
Product
SparkFun Qwiic EEPROM Breakout
512Kbit
-
The SparkFun Qwiic EEPROM Breakout is a simple and cost effective option to add some extra storage space to any project. With 512 kilo-bits (or 64 kilo-bytes) of storage, this product is great for any microcontroller that doesn't have any EEPROM storage space, like the SAMD21. You can use the Qwiic EEPROM for storing data like GPS waypoints and other user settings that need to be maintained between sketch uploads. The SparkFun Qwiic EEPROM has three address jumpers, allowing for up to eight EEPROMs on one bus. All communication is enacted exclusively via I2C, utilizing our handy Qwiic system (as the name implies). However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
n-Line Jumpers on 0.100 [2.54] Centers
Series 152, 156 & 157
-
In-Line Jumpers on .100 [2.54] Centers. End connectors have Gold plated, solid Brass pins on .100 [2.54] centers. Available single-ended (Series 156), double-ended (Series 157), or bare-ended (Series 152). Reliable, electronically tested solder connections.
-
Product
100 Pin Breakout Interface
VSI-Breakout-100
-
The VSI-Breakout-100 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
PCI POST Code Display
post4d
-
During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h or port 84h (jumper selection). Use post4d to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails. Convenient business card size.
-
Product
Modbus or Laurel ASCII ProtocolSerial Output DIN Rail Transmitters
-
Laureate TM Series serial output transmitters can be jumpered for two signal levels: RS232 or RS485. Two serial protocols are selectable in software: Modbus or Laurel's Custom ASCII.Modbus protocol operation is fully compliant with the Modbus Over Serial Line Specification V1.0 (2002) for 2-wire, half-duplex connection.
-
Product
Media Converter, 100Mbps, Single Mode 1310nm, 30km, SC
EKI-2541S
-
Provides 1 x 10/100 Mbps Ethernet port with RJ45 connectorProvides 1 x 100 Mbps Single-mode SC type fiber portProvides internal jumper for Link Fault Pass-through (LFP) settingSupports full/half duplex flow controlSupports store and forward transmissionSupports auto-negotiationSupports MDI/MDI-X auto crossoverSupports redundant 12-48 VDC power inputProvides flexible mounting: DIN-rail and Panel mount
