Combs
-
Product
Optical Frequency Combs
-
The Optical Frequency Comb technology is regarded as a breakthrough technology for measurements with highest accuracy. Lowest phase noise, stable supercontinuum, and turn-key operation make the Menlo Optical Frequency Comb solutions unique in accuracy and reliability. According to our principles: The best Optical Frequency Comb for any application.
-
Product
Hexagonal Wet Film Combs (Stainless Steel)
112 & 3236
-
These hexagonal precision formed stainless steel wet film combs are long lasting, reusable and supplied in a range of thicknesses measuring up to 3,000μm (120mils).
-
Product
Plastic Wet Film Combs
154
-
Metric and Imperial values are on the same comb, 50 to 800μm on one side, 2 to 32mils on the other.
-
Product
Long Edge Wet Film Combs (Stainless Steel)
3238
-
Each comb has 24 measurement steps (teeth) providing a more accurate wet film thickness value.
-
Product
Pressley Fiber Bundle Strength Tester
F215
-
To determine the tensile strength of natural fibers. Includes 1 pair clamps and spacer, torque vice and wrench, cutter, comb and tweezers. A 5mg x 0.01mg capacity balance is required but not included.
-
Product
Comb Generator
CG118
-
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
Product
Comb Generators
-
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
Product
Vector And Scalar Mixer / Converter Measurements
S95083B
-
The Keysight S95083B measurement software includes the scalar mixer / converter plus phase (SMC+Phase) measurement class. It provides fully calibrated conversion gain / loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers. Eliminating the calibration mixer requires a U9391C / F / G comb generator and an external DC power supply. A vector mixer characterization (VMC) is also included for measuring group delay of frequency-converting devices. VMC can be used to characterize a user-supplied calibration mixer.
-
Product
Microwave Comb Generator
-
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Product
Tape Up and Down Conversion Board
LS-37-P
-
The IF Digital processing board is a workhorse for all digital demodulation and combing. It can also support other unique functions like sub-carrier demodulation, FM/FM demodulation and tone receiving. Please consult the factory for your unique requirements.
-
Product
Comb Generator, 10 MHz to 67 GHz
U9391G
Comb Generator
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
Sideband Bus Protocol Analyzer
FS2700 DDR5
-
The FS27xx DDR5 Sideband Bus Protocol Analyzer is the latest DDR5 tool from FuturePlus Systems. FuturePlus has taken the complexity of 8 different JEDEC specifications and ported them into this very useful tool. DDR5 Validation Engineers and system integrators will not have to comb through complex specifications defining thousands of bits and register addresses. The tool takes care of this. Please request our data sheet for more information.
-
Product
Comb Generator
CG 50/500
-
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN.reference signal source Noise Generators Signal Generators
-
Product
Comb Generators
-
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
Product
Frequency Doubling Comb Generator
COMBGEN6DIFF
-
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Product
Comb Generator
RefRad X
-
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
Product
Reference Radiators / Comb Generators
-
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
Product
Desktop stand-alone
-
All Three Sensors Of Optical Comb Can Be Installed On The Gate Type Stage And It Can Be Used As A General-Purpose Stand-Alone Machine. Tasu Since It Is A Rectilinear Laser, Complex Shapes Can Also Be Measured Tasu Measuring Time With A Working Distance exceeding 100 mm can be easily measured + parts with high irregularities can be measured with deep depth of focus
-
Product
Add-ons For Metrology
-
We offer add-on products for Optical Frequency Combs and metrology applications. These include heterodyne photodetectors (BDU), and highly stable RF oscillators, just to name a few.
-
Product
Comb Generator, 10 MHz To 110 GHz
U9391M
Comb Generator
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
Wet Film Combs (Stainless Steel)
Elcometer 115
-
Four separate thickness ranges are available up to a maximum of 1,250μm or 50mils and are manufactured to an accuracy of ±5% of marked value or ±3µm (0.12mil), whichever is greater.
-
Product
NI-9252, ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module
786783-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
Low Phase Noise Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM is committed to an expanding portfolio of low-phase noise (>150dBc/Hz @ 1k Hz offset) amplifiers for critical signal generation applications in test and measurement and defense. These offerings complement our line of NLTL GaAs comb generators.
-
Product
Comb Generator, 10 MHz to 50 GHz
U9391F
Comb Generator
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
NI-9252 , ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module
786782-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a … number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
Integrated Connection Technology
-
Compact design - Connection points for bridge combs - Solder-free circuit board contact - Plug -in connectors for interchangeable modules, such as small relays
-
Product
Comb Generator
WJ10-100A
-
Comb Generator model WJ10-100A with Broadband Antenna. Frequency Range 10MHz - 11 GHz with two frequencies step size option; 10/100 MHz
-
Product
Dual Channel Synthesizer
SYNTH1400X2
-
Convenient Ethernet ApplianceControllable from anywhere by computer or mobile device100KHz to 1400MHz frequency tuning in 190 picoHertz stepsTwo synthesizers are independently programmableBoth synthesizers track due to common reference16-bit phase tuning resolution12-bit amplitude scalingProgrammable modulusAutomatic linear and nonlinear frequency sweeping capabilitySwitchable frequency/phase-offset profilesUltra-low phase noiseOptional pulse comb generator output
-
Product
Radiating Comb Generators
TBCG1
-
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
Product
Comb Generators
-
Macom Technology Solutions Holdings Inc.
MACOM offers a family of Non-Linear-Transmission-Line (NLTL) GaAs Comb Generators offering superior phase noise performance up to -18 dBc/Hz better then a SRD, usable harmonics out to 50 GHz, and available in SMT or connectorized packages. Standard drive levels from 18 - 21 dBm.
