Optical Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-819
-
The SCS-818 and SCS-819 amplifier/filter module provides eight 4-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-818) and 0.5Hz to 70kHz(SCS-819). Each of the SCS-818/SCS-819's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
-
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
-
Product
Digital Video/Audio/Data optical transceiver
OD3000B
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OD3000B digital series optical transceiver, adopts digital video coding technique and WDM technique to satisfied user's multipath digital video, audio, data, ethernet's long distant high quality optical fiber transmission because of its full-found. This model of optical transceiver including single fiber one way digital video, single fiber 64 routes video, 128 routes audio and data uni-direction and bi-direction complication. OD3000B optical transceiver can transmit the camera audio/video signal, camera and tripod head control data as well as other control function to central control room from remote end by optical fiber. It can be widely used in the remote monitoring, video conference, video medical, remote education and other systems of public road, traffic, industrial and mining, community ect.
-
-
Product
Optical Switches
-
This latest technology platform presents the best value in terms of size, form factor, durability, and cost. The design of our MEMS optical switch centers on DiCon's proprietary dual-axes tilting MEMS mirror and is expandable up to a 1x36 switch configuration. Large fan-out 1xN optical switches and non-blocking fan-out/fan-in NxM matrix optical switches are built by cascading multiple of these 1xN switches. The MEMS 1xN fiber optic switch passes the stringent Telcordia GR-1221 qualification and is vastly deployed in today’s optical communication networks. With a lifetime of over a billion cycles, the durability of this MEMS device makes it a perfect choice for optical network monitoring applications that require frequent switching.
-
Product
10 MHz AGC Distribution Amplifier
FS710
-
Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A800DI
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply. Please see A800 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase.
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
High Voltage Optically Isolated Probes
-
High Voltage Optically Isolated Probes are designed to aid in device characterization measurements. Whether it is low or high voltage signals sitting on HV busses, high bandwidth, extreme precision, and optical isolation means floating measurements are easily made with minimal DUT loading.
-
Product
Optical Time Domain Reflectometer
3000 Series
-
Shanghai Baudcom Communication Device Co.,Ltd.
BAUDCOM 3000 series Optical Time Domain Reflectometer (OTDR) is anintelligent meter of a new generation for the detection of fiber communicationssystems. With the popularization of optical network construction in cities andcountrysides, the measurement of optical network becomes short and disperse; The3000 series is specially designed for that kind of application. It’s economic,having outstanding performance.The ODTR is manufactured with patience and carefulness, following thenational standards to combine the rich experience and modern technology, subjectto stringent mechanical, electronic and optical testing and quality assurance;in the other way, the new design makes ODTR more smart and compact andmulti-purpose.
-
Product
Amplifier Operating with High Temperature Accelerometers Where Pyroelectric Effects May be Encountered
Trig-Tek™ 203PC-1/2
Amplifier
Operates with high temperature accelerometers where pyroelectric effects may be encountered, with frequency range from 3 Hz to 40,000Hz
-
Product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode
40-860A-332-HI
Switch Module
The 40/42-860A-332-HI is a PXI/PXIe triple insert/bypass switch with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Amplifier Systems Broadband
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
-
Product
Rolling Seal 4 Optical Connector
RS4
-
- GAF/ELI enhances mating efficiency and eliminates potential for shell damage while offering positive latch indication.- Longer, contoured cable end lead-in bushing enhances fine alignment of connector halves during the mating sequence.- Reduced channel count to align with more efficient field architectures.
-
Product
GN Range Broadband Power Amplifiers 100 KHZ - 200 MHZ
GN Series
-
Class A solid stateBroadband (instantaneous single band): 100 kHz 200 MHzTypical output power : 500 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 450 W and H < -20 dBc up to 100 MHz andP1dB > 180 W and H < -20 dBc from 100 MHz to 200Air cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Optical tables
-
The primary goal of a well designed optical table is to eliminate relative motion between components of test system located on the surface of the optical table because such motion can generate measurement errors.
-
Product
RS422 Mode SI-module With Optical Isolation And RTS/CTS
MX422-PEP
-
RS422 mode SI-module with optical isolation and RTS/CTS
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-018-M50-HI
Multiplexer Module
The 40/42-852A-018-M50-HI is a PXI/PXIe 8-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
LXI Optical Switching - 2:1 Multiplexer Plugin Module
65-281-381
Multiplexer Module
The 65-281-381 2:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
3D Optical Microscopy
-
Bruker is the worldwide leader in 3D surface measurement and inspection, offering fast, non-contact analyses for samples ranging in size from microscopic MEMS to entire engine blocks. Our microscopes are the culmination of ten generations of proprietary Wyko® Technology advances that provide the high sensitivity and stability necessary for precision 3D surface measurements in applications and environments that are challenging for other metrology systems.
-
Product
LXI 16:1 Optical MUX FC/PC Loop-Thru
60-850-223
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Pluggable Optical Line System
POLS
-
Use our compact pluggable modules to provide up to 8 DWDM channels to enable high-capacity optical inter-datacenter links for internet service and cloud hosting providers.
-
Product
4-IN-1 Fiber Optic Power Multimeter
FPM-100
-
Shanghai Fibretool Technology Co.,Ltd.
A power meter is the essential tool for measuring optical power within a fiber optic link. FPM-100 optical power meter is a precise, durable, convenient, portable test instrument. Smart appearance with the backlight, auto-shutdown features, the wide range of optical power testing, test the accuracy of precision as well as a common interface design with 0.01dB resolution.
-
Product
Broadband Power Amplifier
PAS-00023-25
-
* Solid State Power Amplifier* Gain : 46 dB typ.* High IP3, 48.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Over Temperature Protection* Type N Connectors
-
Product
Fiber Optics
-
Blonder Tongue Laboratories, Inc.
Blonder Tongue has a comprehensive line of robust fiber optic transmitters and receivers for optical networks delivering both broadband CATV and data within campus-style environments with up to 1000 MHz bandwidth.
