Network Testers
-
product
Transient Over-voltages Tester
SUG335
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
product
Wireless Network Emulators
Keysight’s industry-leading range of wireless network emulators and device test solutions enable the entire mobile device ecosystem to accelerate the market introduction of new wireless devices by streamlining the workflow from early prototyping, development, and design verification to conformance, carrier acceptance, and high-volume manufacturing.
-
product
High Load Strength Tester
HLST1000Z
This tester measures the tensile or compressive strength of various samples
-
product
Diode Tester
FEC VF40CM
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
product
Digital 130AMP Battery/Alternator Tester
MD4780
For testing 6V and 12V batteries, charging systems, alternator diodes and starter. Industry leading 130 amp load .
-
product
Network Security Testing
Network Security Testing helps to identify the vulnerabilities in the security system of a business and to guide with solutions to improve the security measures. The key objective of network security testing is to identify the security risks, level of possible threats and revenue impact. QA Mentor follows their proven 4-D model and use the derived security measures to secure the business system with help of iterative vulnerability assessment and network penetration testing.
-
product
Digital Battery Testers
Electronic devices designed to test the remaining capacity of a battery's overall charge.
-
product
Peel Testers
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
product
Outdoor Exposure Tester
OET
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
product
Cable Transmission Tester
SIGNALTEK CT
If you install or maintain data cabling, SignalTEK CT allows you to generate PDF test reports that prove installed links run at Gigabit Ethernet transmission rates.
-
product
Concrete Hardness Tester
W-M-250
The W-M-250 Manual Test Hammer is the traditional instrument used for the non-destructive testing of hardened concrete. This easy-to-use instrument provides a quick and simple test for obtaining an immediate indication of concrete strength in various parts of a structure. The minimum verifiable strength is 1400 PSI (10 MPa)
-
product
Network Testing
UX Series
The VeEX UX series includes the robust UX400 and UX400R Universal Expert platforms. The UX400 is the most versatile portable multi-service transport test solution to offer a wide range of modules with test capabilities ranging from DS1/E1 all the way up to the latest 100GE and OTU4 network speeds, for a total of up to 600G traffic generation in a single compact modular chassis. Available in Portable and Rack-mount versions.
-
product
Lithium Battery Equalization Tester
LIFG
Fuzhou Fuguang Electronics Co., Ltd.
The LIFG series Tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem that inconsistent voltage of lithium battery pack. Meanwhile it supports to make the voltage difference of any battery, which can be used for research and development experiments to stimulate what problems will occur when the battery reaches the maximum voltage difference under harsh work working conditions.
-
product
Deadweight Testers
AMETEK Sensors, Test & Calibration
We provide the world’s only ball-type deadweight testers, where the ball and weights float on a thin film of air, which is virtually frictionless. This design eliminates the necessity to rotate the weights during testing, and allows the user to concentrate on the instrument itself. Our testers are engineered to offer user-friendly, safe operation, in the field, or in a lab. Both pneumatic and hydraulic testers are available.
-
product
Torque Tester
CD-100M/10M
Ideal for daily inspection of electric screwdrivers. Use conventional joints. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. 3 times more durable than the conventional model, even with sudden high torque. disassemble the joint due to excessive unwinding .
-
product
PAT Testers Kits
Our PAT testing kits are designed to increase efficiency when testing. We have an excellent selection of PAT testing kits available. They are designed to help the way you work by creating efficiencies and help you get more from your PAT tester in the field. Our PAT testing kits are available with and without software so you can streamline your reporting process and provide a full and complete service to your customers.
-
product
Single Fiber Strength Tester
TB400C
TESTEX Testing Equipment Systems Ltd.
Single Fiber Strength Tester, suitable to test the tension strength and elongation of chemical fiber, cotton, wool, ramie, silk, glass fiber, fine metallic thread, etc.
-
product
Digital Insulation Tester
SK-3502
125V/250V/500V/1000V, Comparator Function., Data Memory (up to 100 data)., Low Resistance Measurement., AC/DC Voltage Measurement., Enhanced Safety Functions.
-
product
4 Moving Probe Tester
L Series E4L6151
This is the latest EMMA series affordable model that offers low damage, high-speed and high-accuracy test. Max. Test Area 24 x 20" (610x510mm). Number of Probes 2 Front, 2 Rear. Min. Pad Pitch *1 0.007087" (180µm). Min. Pad Size *2 0.00314" (80µm).
-
product
Primary Current Injection Tester
SLQ
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
It's a high voltage generator insutrment for tesitng.
-
product
Distillation Testers
AUtomatic distillation apparatus, distillation tester, benzene disitillation tester (low temperature), vacuum distillation tester, distillation tester (double units), distillation tester (low temperature double units).
-
product
RRH/RRH Installation Tester
Integris 2000
Field installation teams for RRH s have a difficult task in validating the installation for proper cabling and RRH operation. This is because the BBU that connects to the RRH is not present during the RRH installation, making it impossible to truly know if the tower cabling and RRH have been installed properly.
-
product
Electrical Test & Measurement Tester
Evolusys Technologies Sdn. Bhd.
• Polarity • Forward & Reverse Voltage• Forward & Reverse Current• Snapback/Thyristor• Open/Short measurement• Contact check (optional-apply for Keithley C series only)
-
product
Coil-on-Plug Spark Tester
TH458
For ignition systems with coil-on plugs, including Ford, Chrysler, Chrysler imports, Mitsubishi, Nissan, and more. Since coil-on plug ignitions do not have plug wires, inductive test equipment cannot be used. Spark tester tests for no-start conditions and measures coil output.
-
product
Environmental Testers
When you’ve got a specialized job to do, general-purpose tools won’t do. Whether you’re measuring sound, light, water or solar energy, depend on Amprobe for affordable, environmental test solutions.
-
product
Oil Tan Delta Tester
Weshine Electric Manufacturing Co., Ltd
The Oil Tan Delta Tester (OTD) is a laboratory instrument, which measures the Tan Delta, Resistivity and Relative Permittivity of insulating liquids. These tests give a wider picture of the overall quality of the insulating oil, and will indicate if there is any contamination. WESHINE has developed features of the OTD to ensure that productivity levels within laboratories are maximised.
-
product
Digital RCD Testers
Used to detect whether the RCD in the circuit can be triggered normally.
-
product
Penetration-Resistant Insert Flexing Tester
UI-FT05
Penetration-Resistant Insert Flexing Tester, also named as Steel Midsole Flexing Tester, is used to test penetration resistant inserts flexing resistance. As described in EN 12568, ISO 20344, the inserts shall exhibit no visible signs of cracking, disintegration or delamination after having been subjected to 1 *106 (one million) flexion cycles.





























