Genrad Fixtures
An I/O test interface platform, created by Pylon adopted and extended by Genrad (now Teradyne).
See Also: Board Test Fixtures
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
Test Fixture
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Standard & Custom Test Fixtures
-
Both standard and custom Test Fixtures from OAI enable the user to integrate the solar cell with the I -V tester. Fixture configurations range from from simple hold down devices to temperature-controlled fixtures with front and back side contact. We invite you to contact an OAI Application Engineer for help with your fixture design. With our expert guidance, you can expect maximum performance from your I -V Tester and Solar Simulator.
-
Product
Burn-In Test Fixtures
-
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMK-04
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
In-Circuit Test Fixture Design Services
-
XJTAG offers consultancy services to design and build production test fixtures that integrate JTAG boundary scan with bed-of-nails testing.
-
Product
HiFIX High Fidelity Tester Access Fixture
-
The HiFIX lineup delivers clean waveform transmission, precision docking, and multi-DUT parallel test, with high reliability.
-
Product
Vacuum Test Fixtures
-
Vacuum fixture kits for Pylon block fixture, Teradyne, Keysight, Digitaltest,Seica, Cobham (Aeroflex), ATX exchangeable system.
-
Product
Test fixtures
-
Offers a wide range of standard Test Fixtures that can fit many of your applications and services. From your R & D to your production lines, we have a solution for you.Each products are standard but we can adapt or design your application.
-
Product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
-
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
Product
Drop-In In-Circuit Test Fixtures
The Chameleon
-
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
Product
ICT/FCT-Fixtures, Max UUT 250 × 180 mm (wxd)
CK-1-228X-S (Small IF) / 230514
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,30 kg
-
Product
Universal Test Fixture
Series 48
-
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
Product
Functional Test Fixtures
-
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
-
Product
Automatic Fixture Removal
S96007B
-
Automatic fixture removal (AFR), is the easiest way to remove fixture effects from non-coaxial device measurements.
-
Product
VOC FIXTURE OVER CLAMP ASSEMBLY'S
-
Test-X VOC Series overclamps are used for testing bare or loaded printed circuit boards with open vias and to minimize board flex.The VOC Series overclamp comes with adjustable delrin pressure fingers, anti-rotating hex nuts, hinge and latching assemblies, mounting instructions and hardware.The VOC Series will accomodate fixtures with dress frames or newer style fixtures using full-size top plates.
-
Product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
-
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
Product
Custom Fixtures
-
Joule mechanical design and manufacture capabilities allows us to create other custom projects to meet your test needs. Joule can design burn-in racks, jigs and stand-alone test station.
-
Product
Open Source Hardware Test/Programming Fixture
OpenFixture
-
OpenFixture is a fully parametric programming/test fixturing solution written in openscad. The inputs are generated/captured from the users board layout software and a laser cuttable fixture is generated automagically.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Tooling And Fixturing
-
Control develops and supplies fixtures and test accessories :*For a vast field of applications - ICT (In-Circuit Test), functional test, Flash programming, EoL (End-of-Line) test systems, etc.*For all handling systems currently used in the market: online or offline, mechanical, pneumatic or vacuum operation*From simple mechanical fixtures, with a few hundred probes and low production volumes, to highly complex accessories with thousands of probes, double-sided probes, double acting, etc.
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
Product
ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)
CK-2 Medium (Hold Down Gate) / 230156
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 450 x 330 mm (wxd)
CMCSK-07-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
RF Functional Test Fixtures
-
EMC Technologies’ design team has developed a variety of test adaptors and test stations for testing RF circuit assemblies and microwave sub-assemblies.
-
Product
ICT/FCT-Fixtures Max UUT 370 × 300 mm (wxd)
CK-2 Large (Hold-Down Gate) / 230158
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
