Resistive Load Banks
Check power source's ability to deliver a given current and voltage at unity power factors.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks
-
Product
In Line Load Cell (200N-5000N)
100 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 5000N with better than ±0.25% non-linearity.
-
Product
Automated Resistance Standard
SmartResistor
-
The SmartResistor combines, into one transportable device, all the items needed to maintain resistance: a set of standard resistors, a controlled temperature bath, a low thermal emf scanner, and measurement data.
-
Product
Resistance Meter
MT8-4L
-
М-module МТ8-4Л is a mezzanine module designed to measure the resistance of resistive sensors using a four-wire measurement circuit in eight channels (eight-channel digitizer). М-module МТ8-4Л is installed on the carrier of mezzanines - module НМ-М and is connected to it via a local information highway. Up to four m-modules of various types can be installed on the NM-M module. The NM-M module, together with the m-modules installed on it, forms a VXI module of size C-1 and is used to create information measuring VXI systems.
-
Product
Dry Dielectric RF Coaxial Loads
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
Load Pins, Tension Load Links, And Load Shackles
-
Interface’s wide range of load pins are designed for the measurement of tensile and compressive forces across a wide variety of applications, including crane/lifting, industrial, marine, offshore, and civil engineering. Machined from high tensile stainless steel, our load pins are suitable for use in exposed situations including prolonged immersion in seawater. Interface’s tension load links are designed for lifting and weighing applications in harsh environments and manufactured from high tensile aluminum and stainless steel. Interface’s load shackles are manufactured from high tensile carbon steel and the basic shackle uses the renowned Crosby G2130, G2140, and G2150 series (depending on the load rating).
-
Product
Load Measuring Pins
-
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Product
Panel-mount Type Resistivity Meter (Four-Wire Transmission, 2-channel)
HE-960RW
-
HE-960RW connects resistivity sensor(ERF sereies) and measures resistivity and temperature in the sample water.This resistivity meter is ideal for such applications as the high-precision water monitoring employed at ultra-pure water plants used in semiconductor manufacturing.They utilize newly designed, high-precision, high-stability temperature measurement circuitry and a vastly improved temperature compensation function, an important element for measuring the resistivity of ultra-pure water.
-
Product
Button Load Cell
3000 Series
-
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
Product
Load Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Load Measurement Trainer comprises of strain gauge based load cell,loading arrangement to load in compression, weights and digital load indicator to read the load in Kg.
-
Product
Industrial Weighing - Wireless Load Cells
-
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
Product
Resistivity Meter for Concrete
Ohmcorr Test System™
-
OhmCorr has two probes spaced 1.97" (5cm) apart which are placed in holes drilled to a depth of 3/8th" (8mm) and filled with conductive gel. The direct digital read-out of resistivity is displayed on the LCD when the control switch is activated. OhmCorr and CorMap, when used together, provide an economical and sound diagnostic system of corrosion in reinforced concrete.
-
Product
High Performance UV Nanoimprint Resist
AMONIL®
-
UV Nanoimprint is a mechanical molding technique. A template made from quartz or a flexible elastomer with a 3D relief is brought into intimate contact with a UV-curable resist spin-coated on top of a substrate. Applying low imprint pressure at room temperature features are filled within seconds due to the low viscosity of the imprint resist. The resist is hardened via UV-light through the backside of the template. Finally substrate and template are separated. The replicated resist relief can further be transferred into the substrate via RIE-process or used as functional element.
-
Product
Femto / Picoammeter and Electrometer / High Resistance Meter
B2980A Series
-
Both the picoammeters and electrometers provide a world-best performance of 0.01 fA (0.01 x 10-15 A) current measurement resolution. In addition, the electrometers can measure resistance up to 10 P (10 x 1015 ), which is also a best-in-class specification. Finally, since AC power line noise can be difficult to eliminate when making low-level measurements, both the picoammeters and electrometers are available in battery powered versions.
-
Product
Load Testing for Evolved Packet Core (ePC/VePC)
Flare
-
Linkbit Flare is designed for load testing of Evolved Packet Core (ePC) networks, and the upcoming VePC deployments. It is based on the technology initially develped for Linkbit functional testers, and as a result is extremely flexible.
-
Product
Transformer Winding Resistance Tester
KRI 9310
-
KRI 9310 adopt Kelvin four-wire testing method, which effectively eliminates the influence of the resistance of the test line on the test results. It can be able to increases the current to 10A by which can test extremely low resistance to 0.01 Ω(such as amorphous alloy, Copper-nickel, nickel-chromium-iron, iron-chromium-aluminum etc). For the tested objects with high resistance value (CT/PT), the instrument can extend the range to 20 kΩ，so the wide resistance test range enables KRI9310 can cover 80% of the power transformer products on the market and switchgear bus-bar cable etc. The power of the tester use the built-in rechargeable lithium battery that can test hundreds of transformers by one time charging.
-
Product
Surface Resistance Meter
WL MIDGET
-
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
Product
Medical Grounding Resistance Tester
2678YM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Medical Grounding Resistance Tester，Product Introduction2678YM Medical Grounding Resistance Tester Is Used To Measure The Internal Electrical Equipment Of Grounding Resistance,Which Reflects The (Contact) Resistance Of Total Grounding Terminal Of Electrical Equipment.It Suitable For Measuring All Kinds Of Motors,Electrical Appliances,Instruments,Household Appliances And Other Equipment Resistan
-
Product
Easy and Non-Destructive Airflow Resistance Measurements of Materials and Parts
CARE+
-
The control of airflow resistance in the production of materials and components is a growing requirement in the automotive industry. CARE+ (Concentric Airflow Resistance Evaluator) is an apparatus designed to measure the airflow resistance of materials and parts. Measuring non-destructively, CARE+ is particularly applicable in the quality control of parts and materials.
-
Product
Single Point Aluminium Load Cell
EST-4
-
Technopark Automation & Control
The EST-4 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 1200 x 1200 mm. This load cell is available in capacities 1000 kg and 2000 kg.
-
Product
Power Supplies And Loads
Power Supply
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
Product
Load Simulator
Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
PCRF Load Tester
-
The Polaris Networks LTE PCRF Load Tester is a comprehensive test solution for evaluating the performance and the stability of LTE Policy and Charging Rules Function. The PCRF Load Tester is ideally suited for manufacturers of PCRF equipment as well as operators deploying PCRF in an LTE network. The Tester can be used for testing both the Control Plane and the User Plane under various load conditions and for measuring the capacity and various key performance indicators of EPC nodes. The Tester simulates millions of Subscriber sessions with multiple bearers per Subscriber.
-
Product
Safety Shoe Electrical Resistance Tester
UI-FT06
-
Safety Shoe Electrical Resistance Tester is to test the electrical resistance of conductive footwear and antistatic footwear.
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
Surface Resistance Meter
-
Wolfgang Warmbier GmbH & Co. KG
Starterkit for testing conductive an dissipative surfaces and electrostatic fields/surface potentials
-
Product
Dummy Load
-
Dummy load is capable of dissipating four times the legal limit 6 kW for 2 minutes and legal limit 1500 watts key down, forever. It covers the 160 meter to 6 meter bands (actually 1 Mhz-60 MHz continuously). It is a dry dummy load intended for testing amplifiers and station conditions. Two fans on the rear of the unit are automatically turned on when the internal temperature reaches 120°F/49°C . The unit runs off a universal AC supply. Simple to operate and use, the dummy load includes an RF sample output of -60 dBc.
-
Product
3U VPX Conduction Cooled Load Board
1940000446-0000R
-
3U VPX Load Board, conduction cooled.
-
Product
DC Electronic Load
EE30180A
-
The EE30180A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running.
-
Product
PXI MUX 2 Banks of 64 Channel 1 Pole
40-610-022-2/64/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Auto Calibration for Load & Extensiometer
-
Jinan Testing Equipment IE Corporation
TE electronic calibration module provides an easy way to calibrate load cell or extensometer and signal conditioning electronics without using a mechanical calibrator. It enables performing on-site electrical calibration and easy to periodically “spot check”, which will help ensure that the load cell and the extensometer and electronics are calibrated correctly.
