PCI Test
-
Product
Remote Test Witnessing
-
DTB can test in a wide range of environmental factors while keeping staff and customers safe.
-
Product
Versatile Test Stand
VTS-2100
-
Applied Scientific Instrumentation
*Base is a Breadboard on 25 mm centers tapped for M6 screws with threaded holes for risers for TE/TI-2000, TE-300, IX-71/81, DMI, and MS-2000 stages.*Base feet provide vibration isolation.*Z riser is adjustable on pillar blocks.*Z motion from LS-50, LS-100, or LS-150 linear stage.*Z illumination can use LED, LED and a Condenser (from below), or fiber illumination (from above).*Observation is with a Modular Infinity Microscope.
-
Product
Functional Testing Services
-
If you're looking for load testing services, you're probably investing heavily in advertising campaigns. But unless you run load tests to ensure your system works properly under real-life load conditions, you can lose both your marketing dollars and potential sales. With UTOR you get the confidence that your application will not damage your business.
-
Product
Radio Testing
-
Testing of radio systems. PHOENIX TESTLAB as an accredited radio testing laboratory, Notified Body for R&TTE Directive 99/5/EC and Conformity Assessment Body offers you a complete service up to your products' worldwide introduction to the market.
-
Product
Hardness Testing Devices
-
Institut Dr. Foerster GmbH & Co. KG
NewSonic’s hardness testing devices test hardness in a nondestructive way using the UCI method (ultrasonic contact impedance). The testing procedure enables quick and mobile measurements (1-second type) to supplement traditional hardness testing. The devices feature compact measurement probes which can also be used in difficult testing positions and component geometries. The areas of application include incoming goods inspection, mix-up checks, production controls, quality assurance, weld seam inspection, cut edge checks, maintenance of built-in components, as well as the replacement of dynamic hardness testing devices in the case of thin materials (below 50mm, e.g. boilers, pipes)
-
Product
PCI Module
PCI-1553-B
-
The PCI-1553-LXE/DXE 1,2 uses UTMC’s Sµmmit LXE/DXE version, UT69151DXE-GPC 1553 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels. The 1553board can have 1 or 2 communication channels. The controller accesses 64Kx16 word of external memory and has internal transceivers for both channel A and B. The 3U PCI board has on-board transformers for both channels and both controllers.
-
-
Product
Portable Test Platform
FTB-4 Pro
-
The FTB-4 Pro is the latest addition to EXFO’s test orchestration portfolio which transforms business as usual into smarter, scalable network testing that significantly increases operational efficiency and provides vital insights into field operations, network performance and service delivery. The 4 slot modular FTB-4 Pro platform enables a unique combination for 100G commissioning, turn-up and troubleshooting which includes the FTBx-88200NGE 100G Multiservice tester (with iOptics transceiver validation software) and the FTB-5240S-P optical spectrum analyzer. There is no need to carry additional platforms or swap modules for unmatched transport and spectral testing on a single platform that no one in the industry can offer. The versatile FTB-4 Pro platform supports a wide range of modules for field testing, data center interconnect, submarine testing, and lab applications for maximum flexibility and ROI across all phases of the service delivery chain: development, deployment, maintenance and troubleshooting. Module combinations on the FTB-4 Pro can also include iOLM/OTDRs, market leading OLTS for fiber characterization, dispersion solutions and other transport modules all with compatibility with EXFO’s market leading fiber inspection probes.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 22.3MΩ
50-297-054
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Single Slot Intelligent Interface Card
IIB-3910-PCI
-
The IIB-3910-PCI is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the PCI Bus.
-
Product
8 Port PCI Express
PEX 8609
-
The ExpressLane™ PEX 8609 offers 8 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 8 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. PEX 8609 architecture supports a high-performance DMA engine with four DMA channels and internal buffer space for internal descriptor support. Up to 256 descriptors are supported internally or alternatively descriptors can also exist in host memory.
-
Product
ESD Testing Service
-
Innovative Circuits Engineering, inc
ICE’s ESD Testing lab has state-of-the-art equipment and in–house technical expertise to perform a whole range of ESD/Latch-up and associated testing services.
-
Product
PCI Express 4-Port
7404e
-
The 7404e PCI Express serial interface provides four multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
FPGA Test System
DO-254/CTS
-
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
Product
Integration testing
-
Integration testing primarily focuses on verifying data communication among different modules of the software project. Integration tests determine the effectiveness and performance of different software modules when they are connected to each other.
-
Product
Compact PCI Bus Analyzer / Exerciser
CPCI650
-
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
Munitions Testing
-
E-Labs has an extensive background in the development and testing of Less Than Lethal (LTL) devices. We were the first to develop a measuring system to capture blunt force or impulse of a round in real time. The Ballistic Impulse Measuring System (BIMS) developed by E-Labs was used on USMC programs to evaluate LTL rounds and compare impulses on a one to one basis.
-
Product
In-Line RF Test Station
AP770
RF Test System
ICT, Functional, Hipot, Vision, ISP and RF test with low cost fixtures in a very compact test station footprint Works with PCBs up to 450×550 mm or with palletized devices Space for up to 25 VPC mass interconnect modules or YAV switching units
-
Product
Torque Testing
-
Torque testers measure properties such as torsional strength and stiffness and are used in quality control of various fields including medical devices, metals, and aerospace
-
-
Product
Protection Testing Accessories
-
Protection testing programs can vary from team to team and company to company.
-
Product
Function Test Fixtures
-
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
Product
Radio Testing RED
-
dB Technology has been providing radio testing services for more than 30 years. With so many electronic devices now containing radio devices, it is critical that manufacturers are aware of their regulatory obligations, and our knowledgeable and experienced team is on hand to provide advice and guidance accordingly.
-
Product
Membrane Conductivity Testing
-
Designed for membrane and separator characterization in a liquid environment. Measure resistance, conductivity, permeability, cross-over, and selectivity.
-
Product
Automation Testing
-
If you want to test all the major features of your application just before release, but you are short of time for complete testing, opt for Automation Testing.
-
Product
Memory Test System
T5835
-
The new T5835 has full testing functionality, from package testing to high-speed wafer testing, for any memory ICs with operating speeds up to 5.4 Gbps, including all next-generation memories from NAND flash devices to DDR-DRAM and LPDDR-DRAM. It can handle 768 devices simultaneously for final package-level testing. It additionally features functions such as an enhanced programmable power supply (PPS) for advanced mobile memories, and a real-time DQS vs. DQ function to improve yield.
-
Product
Test Adapter / Extender
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
Product
Materials Testing
-
Materials testing is a diligent approach to ensuring that your infrastructure and vital equipment will provide continued production, undergo minimal degradation and are designed with optimal performance in mind. Materials testing can also supply a wealth of information about the materials you are developing or incorporating into products to ensure they perform within expected specifications.
-
Product
Custom Test Fixtures
-
For popular high speed components like semiconductor packages, and test contactors, we have developed a custom test fixture which allows the use of high bandwidth microprobes to measure virtually any I/O pin, according to GigaTest's methodology and requirements.
-
Product
Impact Testing
-
Educated Design & Development, Inc.
1250 g body includes release mechanism and striking element guide.250 g striking element comes with cocking knob and hammer head, polyamide face, is hemispherical with a radius of 10 mm, has a hardness of HR85-100.60 g release cone with a 10N release force.Single Impact Force models range from a 0.2 J Hammer to a 2.0 J Hammer.Custom padded carrying case included.
