Optic
-
Product
PIN Photodiode
-
PIN photodiode is a kind of photo detector, it can convert optical signals into electrical signals.This technology was invented in the latest of 1950's. There are three regions in this type of diode. There is a p-region an intrinsic region and an n-region. The p-region and n-region are comparatively heavily doped than the p-region and n-region of usual p-n diodes. The width of the intrinsic region should be larger than the space charge width of a normal p-n junction. The PIN photo diode operates with an applied reverse bias voltage and when the reverse bias is applied, the space charge region must cover the intrinsic region completely. Electron hole pairs are generated in the space charge region by photon absorption. The switching speed of frequency response of photo diode is inversely proportional to the life time. The switching speed can be enhanced by a small minority carrier lifetime. For the photo detector applications where the speed of response is important, the depletion region width should be made as large as possible for small minority carrier lifetime as a result the switch speed also increases.
-
Product
Optical Fiber Identifier
TM301
-
TM301 Optical Fiber Identifier (Live Fiber Detector) is an essential instrument for the installation and maintenance of optical fiber projects. It can easily detect any spot of SM fiber cables. Through inserting a 1310 or 1550 modulated signal into the fiber, it is used to indicate the direction of the transmitting signals, find and locate the specific fiber without interrupting the normal work during the installation, cabling and maintenance.
-
Product
Solid-State Demand Recorder
SSR-6000
-
The TransData SSR-6000 is a Load Profiling Interval Pulse Data Recorder used for recording and profiling pulse data received from electricity, gas and/or water meters. The SSR-6000 features a cover-mounted optical port and remote communications via integrated digital cellular, ethernet, telephone modem or RS232 communications options; and includes totalizing capability for aggregated metering applications.
-
Product
PXI Optical Switch
Optical Switch
The PXI Optical Switch is available in many different switching configurations for customized optical switching. It offers both single-mode and multimode fiber options that can support switching of very small wavelength signals. The switch provides either SC/PC, FC/PC, SC/APC, or FC/APC fiber-optic connectors. You can use the PXI Optical Switch for repeatable, low-loss switching.
-
Product
PXI Single 2 Channel Fiber MUX ST
40-855-512-M
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Multi-channel Optical Power Meter For Swept Test System
MPM-210HMPM-211, 212, 213, 215
-
Our MPM-210H is ideal for IL, WDL and PDL measurement of multi-port optical components including Dense Wavelength Division Multiplexing (DWDM), Arrayed Waveguide Gratings（AWG) , Wavelength Selective Switches (WSS) and more. When combined with our TSL-Series laser equipped with a power monitor output, the MPM-210H allows the user to complete real-time high precision IL measurements.
-
Product
Cladding Alignment Splicer
95EA
-
OFS-95EA optical fiber fusion splicer is designed with high-speed image processing technology and special precision-positioning technology. It will automatically finish the whole fiber fusion process in 9 seconds by fast mode, and splice loss is lower than 0.02dB for single mode fiber. 3.5-inch LCD, dual CMOS monitors, X and Y axis separately display or simultaneously display, thus different fusion stages can be showed clearly. It is compatible with ITU-T SM/MM/DS/NZDS/ED fiber, and is equipped with 4-in-1 holders and SOC adapter.
-
Product
Light-to-Analog Sensors (Current)
-
Renesas' light-to-current silicon optical sensors combine a photodiode array and current amplifiers on a single monolithic IC. These devices are ideal for display and keypad dimming, as well as industrial and medical light sensing applications.
-
Product
EPON ONU
ONU-16FE
-
Hangzhou Softel Optic Co., Ltd.
ONU-16FE is a high cost performance ONU terminal device. (Indoor and outdoor. Gigabit Ethernet/Passive optical network). Provide four 10/100M base-t Ethernet port and one PON port to transmit voice, data and video, etc. ONU-8FE is a high cost performance ONU terminal device. (Indoor and outdoor. Gigabit Ethernet/Passive optical network). Provide four 10/100M base-t Ethernet port and one PON port to transmit voice, data and video, etc.
-
Product
Sensor
VL53L1
-
The VL53L1 is a state-of-art Time-of-Flight (ToF) laser-ranging miniature sensor. Housed in a miniature and reflowable package, it integrates a SPAD (Single Photon Avalanche Diodes) array, physical infrared filters and optics to achieve the best ranging performance in various ambient lighting conditions, with range of cover glass options.Unlike conventional IR sensors, VL53L1 uses ST’s latest generation direct ToF technology which allows absolute distance measurement whatever the target color and reflectance. It provides accurate ranging up to 4m and can work at fast speed (60Hz), which makes it the fastest miniature ToF sensor on the market.With patented algorithms and ingenious module construction, VL53L1 is also able to detect different objects within the Field-of-View with depth information (histogram) at 60Hz. Scene browsing and multi-zone detection is now possible with VL53L1, thanks to software customizable detection array for quicker “touch-to-focus” or mini depth-map use cases.
-
Product
High-resolution Spectrometer
HR2000+
-
The HR2000+ Spectrometer integrates a high-resolution optical bench, a powerful 2-MHz analog-to-digital (A/D) converter, programmable electronics, a 2048-element CCD-array detector, and a high-speed USB 2.0 port. This innovative combination produces and extremely fast spectrometer and provides resolution to 0.035 nm (FWHM).
-
Product
Fused Imagers
-
Fused imagers (fusion multi-sensor imaging systems) offer increased surveillance capabilities due to fusion of classical thermal image with classical visible image. The fusion systems are typically built by combining optically images from thermal imager and classical night vision device, or by combining digitally images from thermal imager and digital night vision devices (or electronic VIS-NIR camera).
-
Product
Hunting Laser Rangefinders
-
The ultimate in efficiency, the Fusion melds the best of Bushnell binoculars with world-leading laser rangefinding capabilities. Every detail is magnified with rich contrast and stunning clarity from edge to edge using premium fully multi-coated optics and BaK-4 prisms. At the push of a button, it displays exact distance to your target from 10 to 1,760 yards.
-
Product
Translation Stage
XYZ 2000 Series
-
Quarter Research and Development
The Model XYZ 2000 Series translation stage was intended for moving optics and microscopes around. This unit is capable of handling loads up to 50 lbs and moving in increments as small as .0005 mm or half a micron.
-
Product
Refractive Index Profiler
S14
-
The S14 Refractive Index Profiler complements optical fiber preform analysis measurements by providing highly accurate and precise characterization of the refractive index profile of drawn single-mode, multimode, and specialty fibers using the RNF (Refracted Near Field) technique. The S14 index profile data produces fiber geometry information directly. Manufacturers can also use S14 data for the prediction of fiber transmission parameters such as mode field diameter, cut-off wavelength, and chromatic dispersion.
-
Product
IP QAM
SHP200D
-
Hangzhou Softel Optic Co., Ltd.
SHP200D 10G IP QAM processor is an all-in-one device developed by SOFTEL which integrates multiplexer, scrambler and modulator in one body with maximum 112 DVB-C QAM channels output. With 10G switch built in, it can process 10G optical signal to work as a traditional QAM modulator. This processor is equipped with 2 card slots to load 32ch or 48ch or 64ch QAM card. Its high density helps operators to save cost to the most extent.
-
Product
PCI Express 2-Port
7203e
-
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
Optical Modulation Generator Software
81195A
-
The Optical Modulation Generator Software 81195A introduces a new approach to optical test. Combined with the M8195A AWG it speeds up your test by a factor of up to 100 with its unique real-time mode. This helps design engineers of long-haul and metro optical transmission applications to maximize test efficiency and thus reduce development time and cost.
-
Product
Collimators
-
Collimators are optical systems used to imitate standard targets placed in "optical infinity" (very long distance). The collimators are used for projection of image of reference targets into direction of tested imagers. According to type of optical elements used in design, collimators are divided into two groups: reflective collimators and refractive collimators. Reflective collimators due to their wide spectral range are almost exclusively used in systems for testing thermal imagers and are also preferable in systems testing TV cameras, SWIR imagers, laser systems or multi-sensor surveillance systems. Refractive collimators are mostly used in systems for testing night vision devices or TV cameras working in visible/near infrared range.
-
Product
Digital Refractometer °Baumé
MA883
-
Thousands of food and beverage professionals and hobbyists, from chefs and food quality professionals to brewers and wine makers, have moved to digital °Baumé measurement from less accurate and less precise optical refractometers.
-
Product
Fiber Optic Power Meters
FOD1204H
-
The FOD 1204 & FOD 1204H Fiber Optic Power Meters are intended for accurate measurements of up-to-date optical communication. Very small temperature and temporal variations of Loss in Fibers and Connectors. Calibration of Optical Attenuators, Light Sources etc.
-
Product
Fiber Optical Cabling
-
An optical fiber, or optical fibre in Commonwealth English, is a flexible, transparent fiber made by drawing glass or plastic to a diameter slightly thicker than that of a human hair.
-
Product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
-
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
IR Thermometer
DIT-500
-
Temperature meters operating in the infrared are used to determine the temperature of the surface of the item. The optical system of the device detects the emitted, bounced and sent energy, which is collected and concentrated on the detector. Electronic system translates optical data into temperature value. In order to increase accuracy the laser pointer is built-in the device.
-
Product
LXI Single 32 Channel Fiber Multiplexer LC, Single-Mode
60-850-414
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Absorption Probe
ASD12-N
-
The ASD12-N absorption probe has a durable LED light source for direct installation into laboratory bioreactors and disposable bioreactors for measuring cell growth and optical density. The probe is available in three different lengths to fit any vessel and is suited for sterilization / autoclaving procedures.
-
Product
100G,200G DWDM OADM Module (4,8-Channel)
-
Flyin Optronics 100GHz/200GHz wavelength multiplexer(100,200G DWDM OADM Module) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add or drop at a ITU wavelength. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
Product
Rugged, High Performance RDE Elemental Analyzer
SpectrOil M Series
-
The latest SpectrOil M series is the eighth generation RDE Optical Emission Spectrometer for elemental analysis in oil and fuel. It is a compact, rugged, transportable and easy to use optical spectrometer that meets military shock and vibration and environmental test standards. The analyzer can be placed in the toughest remote locations around the globe, while still maintaining the laboratory grade accuracy and sensitivity needed for aerospace engine test requirements.
-
Product
Telecom Production Optical Spectrum Analyzer 1200 - 1650 nm and 700 - 1700 nm
AQ6360
-
The AQ6360 is the fastest optical spectrum analyzer for optical device manufacturing offered by Yokogawa. It is a cost-effective optical spectrum analyzer ideal for industrial manufacturing of telecom devices such as lasers, optical transceivers and optical amplifiers. The AQ6360 features a wavelength range of 1200 to 1650 nm for ideal manufacturing test performance.
-
Product
Measuring System for Assessment of Optical Radiation Safety
IEC62471
-
The system is designed especially for the determination of optical radiation hazard exposures specified in IEC62471, such as actinic UV hazard exposure for the skin and eye, near-UV hazard exposure for the eye, retinal blue light hazard exposure, retinal thermal hazard exposure, thermal radiation hazard for eye and skin, for LED products, UV-Lamps, lighting sources, luminaires and etc.
