Earth Testers
See Also: Earth Resistance Testers
-
-
Product
5-50V AC/DC Voltage Tester
1930A
-
Peaceful Thriving Enterprise Co Ltd
*Reinforced casing.*With cETL Approval.*Check voltage on 5-50V AC/DC.*Insulated housing and test leads.*Pocket clip for added convenience.*Built-in LED indicator will glow when voltage is present.
-
Product
Load Stability Tester
TruMotion™ Acceleration
-
When transport vehicles accelerate, turn or brake, the resulting low-frequency accelerations can cause unit loads to shift. Due to both safety issues and potential product damage/waste, regulatory bodies are requiring testing that’s closer to reality – assuring safe and stable unit load integrity!
-
Product
Heat Seal Tester
HST-01
-
Jinan Leading Instruments Co., Ltd.
HST-01Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated filmsaccording to the requirement of relative standards. The seal parameters includeheat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
Product
Ground Set Tester
-
Self-contained, portable convenienceThis tester provides an easy way for an electric utility to check the resistance in protective grounding sets used by line personnel.
-
Product
Network Connectivity Testers
-
The PingerPro Series provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
6-12V Heavy Duty Circuit Tester
1668
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. To indicate whether there is an electrical potential at any low voltage point in the system. By using the pointed contact tip to pierce insulation on cables, it will also indicate if current is present. This can be helpful when tracing faults or add cable to a circuit.
-
Product
VME Bus Tester
VBT100
-
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
Product
Bit-Error-Ratio Tester
OPBX280
-
The OPTELLENT OptoBERT™ OPBX280 is a cost-effective easy-to-use bit-error-ratio tester (BERT) for testing components and systems in R&D and manufacturing environments at data rates up to 28 Gb/s. The OPBX280 incorporates an internal reference clock, a pattern generator, clock recovery, and a BER analyzer, in an extremely compact module.
-
Product
Leakage Current Tester
-
Aarohi Embedded Systems Pvt. Ltd
“ AAROHI” make Leakage current tester is very compact & specially designed microprocessor based instrument to measure mA of motor,Stator.
-
Product
sonic tester
PR-82
-
The PR-82 sonic tester has been modified for the automotive industry. This gauge is commonly used for measuring the thickness of cylinder walls, head ports, decks, tubing, body panals, and windshields. It also has the ability to scan the length of a part to find the the minimum thickness.The PR-82 is back-lit and the unit operates for up to 200 hours on a single set of batteries. It is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
ProxiLAB Quest Contactless Tester
-
Fully programmable card (PICC), reader (PCD) and NFC signal emulator for device characterization and protocol conformance verification. ProxiLAB Quest offers the performance and features required for full characterization and conformance validation of all 13.56 MHz contactless technologies, including the latest very high bit-rate evolutions. ProxiLAB Quest integrates with a variety of conformance certification solutions and test automation platforms.
-
Product
Ultrasonic Testers
-
Our Ultrasonic Thickness Gauge range, is the widest selection on the market with the best cost/performance ratio. On some of the models the warranties are extended up to 5 years while all of these gauges are efficiently and fully backed up and supported. These models are normally carried in stock for fast delivery.
-
Product
Melt Flow Testers
-
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
-
Product
Battery Leak Testers
-
Battery leak testers are crucial tools in the quality assurance process for battery manufacturing. These testers are designed to detect any leaks in battery cells, ensuring that the batteries are safe and reliable for use. Battery leaks can lead to reduced efficiency, potential damage to devices, or safety hazards. By employing sophisticated techniques, such as pressure decay methods or helium detection, battery leak testers can identify even the smallest imperfections in battery casings. These testers are essential in industries where battery reliability is critical, such as in automotive, consumer electronics, and renewable energy sectors, ensuring that the batteries meet stringent safety and quality standards.
-
Product
Harmonics and Flicker Testers
-
complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*.
-
Product
Electromagnetic Field Tester
-
The EMF tester is designed to provide user a quick, reliable and easy way tomeasure electromagnetic field radiation levels around power lines, home appliancesand industrial devices.
-
Product
Conventional friction and wear tester
EFM-III
-
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision.
-
Product
Electromagnetic Force Micro Tester
Micro-Servo
-
This is a multi-functional fatigue testing machine suitable for specimens, structures and full-sized parts. It is an overhead actuator type with a broad test space, so it is ideal for various types of environmental tests, such as those in corrosion tanks or constant temperature tanks.
-
-
Product
Insulation & Multifunction Tester (LCD Display)
1154 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Gas Permebility Testers
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Gas Permebility Testers used to test the gas (o2,N2,C o2, ect) transmission rate of packing materials, such as plastic film, composite film, aluminum-plated film, and so on.
-
Product
Relay / Magnetic Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
Product
AC Programmable Hipot Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
AC Programmable Hipot Tester
-
Product
Rockwell Hardness Testers
-
Is the most commonly used method to determine a material's hardness and is suitable for almost all metals and to some degree for plastics. It measures the permanent depth of indentation produced by a force/load on an indenter.
-
Product
Discharge Tester
-
It is a new impulse winding tester that incorporates high precision, a wide range of functions, various expandability, improved operability, and a full range of external communication interfaces.
-
Product
Cable Testers
CableJoG 64
-
CableJoG 64 can test up to 64 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in the cable testers memory to produce a pass/fail indication of each pin connection.
-
Product
Reciprocating friction and wear tester.
-
This testing machine is used to evaluate surface conditions such as friction faces of materials by measuring the frictional force.
-
Product
LOADpro Load Testers
-
LoadPro is an external Web load testing service. A LoadPro test simulates actual user traffic from outside your network, stressing your entire infrastructure in order to discover bottlenecks that impact performance under peak traffic.
-
Product
Servo Tester
105
-
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
