Counting
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
Digital Fiber Multiplexers & Wavelength Shifters
FiberSaver Series
-
We don’t always have unlimited amounts of fiber at our disposal. Whether working in pre-fibered event venues, houses of worship or moving camera signals across busy metropolitan areas, fiber counts can quickly add up – especially when bi-directional optical transmission is required. MultiDyne’s FiberSaver Series is built for the system designer who needs a robust yet compact solution for signal links where fiber strands are limited, or where fiber feed requirements exceed budgets. FiberSaver products help technicians send and receive more optical signals over fewer fibers. Wavelength-agnostic inputs will multiplex just about any digital optical coming from SMPTE cameras, Network Switches, etc., and combine them with several optical matrix inputs. Scalable in increments of six channels, content producers now have a cost-effective solution to carry extra signals for sports production, distance learning and remote broadcasting.
-
Product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Parallel Testing of Multiple DUTs with High RF Channel Count
Test Rack UTP 7033 RF for validation
-
Our basic test rack UTP 7033 (33 rack units) is intended for equipping with various products and therefore for various application areas.The rack shown here as an example is prepared with products and measurement instruments to test automotive devices with high channel count.
-
Product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Energy & Process Monitor
-
Real time monitoring and reportingComposite system with EMS and PEMSDesired reports like, Doff wise, shift wise, count wise, production, energy, UKGSpeed Vs Kw curve, trends, bar graphs, comparisonsAlerts on higher UKG, lesser production, utilization & power fluctuations.Maintenance alerts based on run hours production cost analysis - Cost Audits - Energy Audits
-
Product
cDAQ-9171, 1‑Slot, USB CompactDAQ Chassis
781425-01
Chassis
1‑Slot, USB CompactDAQ Chassis - The cDAQ‑9171 is a bus‑powered, CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9171 also has four 32‑bit general-purpose counters/timers that you can access through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
PCIe-6341, PCI Express, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device
781046-01
Multifunction I/O
PCI Express, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
DIGITAL MULTIMETER 3 3/4
IBL-19RS
-
International Biological Laboratories
This is a 3-3/4 Digits 3999 Counts with anunciator Autoraning Professional Digital Multimeter with the facility for PC interface to download all the measuring data to the PC through RS-232 PC Interface.
-
Product
PXI BRIC8 FIBO Matrix Dual 80x4 3pin brkout
40-592A-104
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI-2599, 26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
778572-99
Relay
26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2599 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2599 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
PXI High Density MUX BRIC, 24-Chan, 40-Pole
40-570-216
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Advanced Multimeter
7117
-
Peaceful Thriving Enterprise Co Ltd
This is a low power consumption, high accuracy and stable hand held 6000 counts multi-meter; with special designed IC to support true RMS measurement. It performs measurements of DC voltage/current, true RMS AC voltage/current, resistance, capacitance, frequency, diode, continuity, temperature and non-contact voltage sensing.
-
Product
10K Counts DMM With Switch/relay Counter
U1241B
Relay
10K counts DMM with switch/relay counter for glitch detection in installation and maintenance troubleshooting.
-
Product
Basic Multimeter
7116
-
Peaceful Thriving Enterprise Co Ltd
This is a low power consumption, high accuracy and stable hand held 2000 counts multi-meter; with special designed IC to support true RMS measurement. It performs measurements of DC voltage/current, true RMS AC voltage/current, resistance, diode, continuity, temperature and non-contact voltage sensing.
-
Product
Avalanche Photodiodes
-
Excelitas offers Avalanche Photodiodes (APDs) on both Silicon (Si) and InGaAs materials. Si APDs cover the spectral range of 400 nm to 1100 nm and the InGaAs APDs cover 950 nm to 1550 nm. An Avalanche Photodiode (APD) provides higher sensitivity than a standard photodiode and is for extreme low-level light (LLL) detection and photon counting.
-
Product
PXIe Very High Density Multiplexer, 2A, 79-Channel, 2-Pole, Multiple Channel Mode
42-611B-002-M
Multiplexer Module
The 40-611B-002 (PXI) and 42-611B-002 (PXIe) modules are 79-Channel 2-Pole multiplexers. A 158-Channel 1-Pole configuration is also available. They use high quality electro-mechanical signal relays allowing switching up to 2 A and voltage up to 300 VDC/240 VAC. They are suitable for signal routing in high channel count ATE and data acquisition systems. Connections are made via a front panel 160-pin DIN 41612 connector.
-
Product
PXI 3A Power MUX BRIC, 9-Channel, 16-Pole
40-571-203
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Crystal Vibration Tester 1HZ~100MHZ
-
Shenzhen Chuangxin Instruments Co., Ltd.
1 It's using reciprocal counting technique, high accuracy, wide measuring range, truly equal precision measurement, fast speed measurement, high sensitivity.2 single-chip microprocessor technology cycle frequency measurement and intelligent management, making the instrument has high reliability and excellent performance / price ratio.3 It's using LSI design, the use of CPLD devices, instrument components greatly reduced, reliability has been greatly improved, the average time between failures ≥10000h. The machine looks nice, small size, light weight, easy to use.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 1-Pole
40-321-101-HI
Multiplexer Module
The 40-321-101-HI (PXI) and 42-321-101-HI (PXIe) are quad 5-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 23-Channel, 2-Pole
40-321-127-HI
Multiplexer Module
The 40-321-127-HI (PXI) and 42-321-127-HI (PXIe) are single 23-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
SparkFun 6 Degrees Of Freedom Breakout
LSM6DSO (Qwiic)
-
The SparkFun LSM6DSO 6 Degrees of Freedom Breakout is an accelerometer and gyroscope sensor with a giant 9kB FIFO buffer and embedded processing interrupt functions. Due to the capabilities and low cost of the LSM6DSO we've created this small breakout board just for you! Each LSM6DSO breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DSO breakout you will be able to detect shocks, tilt, motion, taps, count steps, and even read the temperature!
-
Product
6,000 Counts Dual Display Digital Multimeter With VFD Feature
KM-711
-
Kusam Electrical Industries Limited
• VFD-V & VFD-Hz in Dual Display• 5msCREST-MAX capture mode (Peak Hold)• Autoranging Relative -Zero mode• Display Hold• EF-Detection (NCV)• Beep-Jack input warning• Hz Line Level Frequency• Hz Logic Level Frequency• Diode Test• Continuity Test
-
Product
Mechanical Counter
SP101/102 Series
-
The SP-101/102 Series is a heavy duty totalizer. It has a double sided shaft for stability. Available in Revolution or Rotary type movements. Input shaft direction is choice between top going or top coming. Count speed range from 300 ~ 3000 rpm. It is a available in 4 or 5 digits with a large digit size of 6.0 x 4.0mm. Resetting of count value is done easily with the front push button reset.
-
Product
Event Detector
-
The Event Detector automatically extracts sound events from an entire sound file according to the user's event specifications. The user digitizes sound data into a continuous sound file, then configures the Event Detector for the events of interest. Detection is based on spectral, temporal, and amplitude criteria. The detector scans the entire file, identifying the desired events and extracting them to individual sound files or measuring their parameters. Detected events can be immediately analyzed in SIGNAL to measure, count, compare, classify, time-stamp, and store sound events and sound parameters. The Event Detector is a module inside SIGNAL and requires SIGNAL to operate.
-
Product
Saluki SFS-2000 Fusion Splicer (4 motors)
-
SFS-2000 series is the new standard 4 motors fusion splicer. Light Weight, Touch Screen, Friendly UI, Fast Fusion and Heating, makes it very popular and hot.* 7s fast splicing, 14s highly efficient heating* 320/88 times image magnification, 5mm fusing for ultra-short cleave length* 10000 groups of fusion records storage* 300 groups of splice modes, 100 groups of heating modes* 220 counts of splicing and heating cycles with build-in 6800mAh Li-on battery
-
Product
PXI BRIC8 FIBO Matrix Dual 248x4 2pin Brkout
40-592A-118
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines. Typical applications are in automotive and aerospace industries which involve safety or mission critical systems that have to behave predictably when cabling or sensor faults occur.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
782052-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
PXIe-2748, 3 GHz, 16x1 PXI RF Multiplexer Switch Module
780587-48
Multiplexer Module
PXIe, 3 GHz, 16x1 PXI RF Multiplexer Switch Module—The PXIe‑2748 is a PXI RF multiplexer switch module that is ideal for switching RF signals up to 3 GHz in production test applications. The high channel count of the PXIe‑2748 makes it well-suited for test systems that require switching a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. It also features onboard relay counting for relay monitoring.
-
Product
98 lane, 98 port, PCI Express
PEX88096
-
The PEX88096 is our highest port count switch in the new PEX88000 PCIe Gen 4.0 series from Broadcom. This new product family builds on the longevity of the PEX series of switches, now spanning 12 families. The PEX88096 switch allows Data Center and Cloud Providers to build flexible, scalable rack infrastructures, along with other advantages.
