-
Product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
-
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
Product
Thermocouple Alarm Setting Transmitter
Model TAT
-
Kusam Electrical Industries Limited
• 4 Digits Display For Input Signal:0 - 9999 • Output Signals Are Programmable. • Ultra-thin Dimension, 27mm width. • Non-Combustible PC Case .DIN Rail or Wall Mounting. • High Dielectric Strength ( AC 2KV / Min , Input / Output / Power )
-
Product
Butt Set
MT-8001
-
Recognized as the new industry standard, the MT-8001 butt set provides superior quality at an affordable price. With its high impedance monitor for data safe operation, technicians can clip onto a line in Monitor mode without disrupting existing traffic. Prokit's unsurpassed protection standards and durability assure the butt set will keep working even in the toughest environments. New weatherproofing provides enhanced resistance to severe weather conditions.Features
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
-
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
Desktop PCB Test System
BOARDWALKER 9627
Test System
Qmax Test Technologies Pvt. Ltd.
QT9627 is a cost effective entry level model Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test .Maximum Digital Test Speed 10MHz in the QT9627 .
-
Product
Lower-Cost Small Footprint In-Circuit Test System
TestStation LHS
In-Circuit Test System
The TestStation LHS in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne’s popular, award winning TestStation product family. Compatible with existing TestStation LH fixtures.TestStation LH features the voltage accuracy and backdrive current measurement embedded in Teradyne’s SafeTest protection technology for accurate, reliable and safe powered-up testing of new low-voltage software.
-
Product
6TL10 Table Top Test Base
H71001000
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettes.The platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Coaxial Attenuators Set
11581A
Attenuator
The Keysight 11581A contains a set of four Keysight 8491A attenuators 3, 6, 10 and 20 dB with type-N connectors, furnished in a walnut accessory case. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Test Fixture
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
Product
MP field sources calibration set
-
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
Product
Burden Set – Current
BSC-102
-
The industry has recognized the actual load (burden) on CTs is lower than the standard ANSI burdens allow. So a new IEEE Specification (IEEE C57.13.6) accommodates that fact by introducing two new burdens and two new accuracy classes. This new specification address “High Accuracy”CTs.
-
Product
Thermometer Set
94029
-
A complete kit for accurate temperature monitoring in all application areas. Supplied in a rugged carry case with foam insert.
-
Product
Iridium Physical Layer Test Systems
PLTS
Test System
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
Product
Power Probe III Set
PP319FTC
-
Full functioning voltmeter measures in 1/10th of a volt increments from 1/10th of 1V up to 70V. Easy to read dual polarity indicators: red (+) symbol indicates positive green (-) symbol indicates negative. Circuit breaker protects the vehicles electrical system and your Power Probe. 20' extension lead gives you 40' total of lead. Great for RV'S, trucks and trailers.
-
Product
Test Program Sets (TPS)
-
Data Review, Corrections, & Generation (Reverse Engineering). Technical Requirement Documentation (TRD). Test Strategy Reports (TSR). Test Program Development – Software. TPS Sell-Off & Acceptance. Life-Cycle Support. Technical Interface Test Adaptors (ITA) – Hardware. Training - TPS Development, ATE/TPS Operator, Fault Diagnostic, ATE Maintenance.
-
Product
Miniature Two-Point Probe Set
PRF-922B
-
The PRF-922B Miniature Two Point probe accurately measures point-to-point resistance of small areas. Like Prostat's PRF-912B Miniature Concentric Ring, the PRF-922B is capable of measurements up to 1.0x1012 ohms. Built-in distance stops provide consistent electrode to sample pressure for developing repeatable measurements. Use the PRF-922B to measure small material samples, hard to assess molded areas, edges of parts, tray or tape cells and other very small objects and surfaces. The assembly is supplied with replaceable conductive electrode covers to enhance contact resistance on irregular surfaces and composition materials. Thus, measurements may be made with either the gold plated electrode contacts, or via conductive rubber covers.
-
Product
Orange5 Programmer + Full Set Of Adapters
-
Orange5 a programmer for programming memory and microcontroller motorola. The advantage of Orange5 is built macrolanguage to save protocols. It gives the ability to add micro schemes, meeting the requirements of manufacturers’ read and write algorithms.
-
Product
Automotive Electronics Functional Test System
TS-5020
Functional Test
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
Product
Interactive Benchtop Test
test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
Bottom Electrode SMD Test Fixture
16197A
Test Fixture
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
Standard Air Capacitor Set, 1pF To 1000pF
16380A
-
The 16380A is a standard capacitor set consisting of four precision capacitors - 1pF (16381A), 10pF (16382A) 100pF (16383A), 1000pF (16384A). These capacitors are primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using these standards.
-
Product
PXI Semiconductor/IC Test System
Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
5k Voltage Probe (set Of 3)
5KVPSet
-
5KVPSet is a set of three voltage probes that allow direct connection to up to 5,000 Vrms 3 phase power.
-
Product
Prototyping & Test Consulting Services Solutions
test
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
Product
High Pressure/Low Set Point Pressure Switch
J205G
-
The J205G High Pressure Low Set Point Pressure Switches are among our most versatile offering, affording the end user an extensive operating environment and a wide range of set point optionality.
-
Product
6TL08 Benchtop Test Platform
H710008
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Charging Sets(AP)
-
The Parker Charging kit is an indispensable instrument for checking, adjusting or filling nitrogen into most of the hydraulic accumulators available on the market.
-
Product
Optical Filter Sets
-
Our filter sets support a great range of fluorophores for microscopes and imaging systems. Patented design techniques drive some of the most spectrally sophisticated optical filters on the market. High transmission, steep edges, precise spectral edge placement, and optimized blocking combine for more reliable measurements. A wide selection of individual bandpass filters and dichroic beam-splitters support unique applications, and world-class manufacturing and cutting-edge metrology ensure consistent performance that always meets specifications.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
