Tone
-
Product
Tone Generator
-
Control and test 2-way radio systems, repeaters, ANI, Paging and more. Activate 2-tone or 5/6-tone pagers. Operate or test EIA tone-remote systems. Record generated signals to a WAV file Accomplish MORE, by carrying LESS hardware in the field. Monitor inputs and outputs with our FREE built-in audio scope and spectrum analyzer. No external hardware required. Output may be fed directly into radio, twisted pair, or service monitor.*
-
Product
Online Tone Generators
-
Output of our tone generators will be downloaded straight to your computer as a .wav file. In other words, our waveform generators will generate high quality sound files, but won't play them online, ensuring the highest sound quality one can obtain on a computer. Single Frequency: Sine Tone Generator, Square Tone Generator, Sawtooth Tone Generator, Triangle Tone Generator. Dual Frequency: Dual Sine Tone Generator (IMD Test). Variable Frequency (sweep) Audio Signal Generators: Sweep Tone (Chirp) Generator.
-
Product
Tone Generator with Cable Tracer
1RA470
-
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
Product
Tone Coax Cable Generator
240 HAL
-
The AINES 240 HAL Tone Generator is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
Product
Tone Generator
140BMC/6P
-
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a.Clear line. b.Busy line. c.Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
Product
Tone Test Set
240 Weathertite
-
The AINES Model 240 Tone Test Set is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
Product
Audio Test Tone Generator
ToneGenerator
-
Tone Generator is a sine wave generator, frequency generator and signal generator that lets you create audio test tones, sweeps or noise waveforms using your computer or a PDA handheld. Generate sine wave, square wave, triangular waveform, saw tooth waveform, impulse, white noise and pink noise.
-
Product
Audio Test Tone Generator
Tone Plug
-
The TONE PLUG offers five user selectable sine wave test tones at frequencies of 100, 250, 400, 1K and 10KHz. An additional 5 special function test signals are also provided.
-
Product
Tone And Probe Kit
3PK-NT023N
-
For professionals who need fundamental wire identification tools without the extra cost, the 3PK-NT023N basic Tone and Probe Kit is the answer. Use it on de-energized AC wire, telephone/twisted pair wire, all voice and data category rated cable, speaker wire, virtually any cable or wire!
-
Product
Variable Tone Generator
-
> 60 Hz to 18 kHz approx> 1.3 VAC P/P> Frequency & Level Pots> Sine or Square Wave> 4.5 x 2.5 x 1.1 inches> 9 volt battery operation
-
Product
Tone & Probe Kits
-
Triplett Test Equipment & Tools
ProTone Wire Locator Kit features a powerful tone generator and a filtered, ultra-bright lighted probe. The CTX590 functions as a high quality wire locating tool that uses an inductive probe to sense a tone placed on the wires by its associated tone generator. The tone generator provides RJ11, RJ45 and insulated alligator clip connections. The Red/Green LED on the probe indicates continuity, voltage, and polarity. The probe also includes an ultra bright LED tip, fluorescent light noise filter and sensitivity control. The CTX590 can be used for tracking down short circuits, telephone central office connections, and other wire locating applications. Includes (2) 9V batteries and case.
-
Product
Tone Generators
-
Traditional Tone Generators were designed for one primary mission; to identify the termination point of a cable. Unfortunately, these were designed for telephony, not network maintenance.
-
Product
Tone Generator
A15TG
-
The Shure A15TG Tone Generator is a battery-powered 700 Hz signal source used to troubleshoot audio systems by checking microphone lines for correct patching and detecting unusual noise that is present. The output level of the A15TG is approximately 42 dBV.
-
Product
Cable Tester
CT100
-
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
Product
ELT STALKER Vector-finder
VF-121
-
The Vector-Finder Types VF-121 and VF 121A are unique in the Vector-finder series of direction finding antennas. They incorporate a proven design, electro statically shielded loop sensing element with modern solid state low noise analog and digital technology to allow detection and location of aircraft band signals. Both the VF-121 and the VF 121A incorporate a unique digital modulator which allows the user to more easily home-in on unmodulated carriers. Such cases occur at airports when transmitter may be accidentally keyed on during aircraft overnight layovers. The VF-121 is specifically designed to be used on airport premises where signal strengths are high. To compensate for very strong signals, an integral attenuator is also incorporated to allow the user to operate the unit close-in to aircraft. The VF-121A differs in that a high gain, low-noise preamplifier is utilized with the sensing element in order to hunt signals that may be weak or at a distance. The unit is ideally suited for the location of ELT transmitters in the field. Both units are tunable over the 118 MHz to 130 MHz aircraft frequencies and interface directly to the user’s aircraft band receiver or transceiver via the antenna jack. With the antenna system connected to the receiver, the user will hear the desired signal. If the signal is unmodulated, the digital modulator will generate a tone on the carrier. When the handheld unit is rotated about, an audible null on the received signal or the generated tone will be heard. This null aligns with the axis of the equipment case and represents the direction of the received signal. This direction may be read from the black dial compass mounted on the top of the enclosure. As the response is bi-directional, triangulation may be used to determine the true bearing when the true direction is not known.
-
Product
IF Receivers, Digital Demodulators and Combiners, TM Displays
-
The IF Digital processing board is a workhorse for all digital demodulation and combing. It can also support other unique functions like sub-carrier demodulation, FM/FM demodulation and tone receiving. Please consult the factory for your unique requirements.
-
Product
Digiair PRO CATV
-
Perfect for digital CATV installations (QAM).• Handy spectrum-analyzer for frequency 45-860MHz.• Easy digital readout of MER, BER and Constellation diagram.• QAM16, QAM32, QAM64, QAM128 & QAM256.• Analog signal level reads out in dBuV, dBmV and dBm with maxholdfunction.• Presents one channel readout with high resolution or six channelssimultaneously or the complete spectrum.• Very sensitive, easy to maximize weak and strong signals.• Built in beeper (pitch tone) and maxhold function.• Tilt function.• Replacable, rechargeable battery (8x AA 1200mA).• Power supply and car-charger enclosed.• Rubber carrying-case enclosed.
-
Product
USB Interface
PK-232/USB
-
The PK-232/USB brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232/USB is compatible with all Windows W2K,XP,Vista/Win7 software terminal programs for the PK-232.
-
Product
50-Watt Rack Mount Transmitter
FLS-2
-
Fiber optic cables are a critical part of modern life due to the vast amount of data they carry to support businesses, internet users, and emergency services. The cost of losing these services, even temporarily, is immeasurable. The FLS-2 system is designed to assist in locating, monitoring and providing damage prevention to these cables. The FLS-2 high-performance, high-power rack-mounted transmitter is typically mounted in a re-gen staton, customer access point, or central office. The FLS-2 transmits a locate tone on the metallic sheath of the fiber cable over vast distances to ensure the cable can be located quickly and accurately, even in congested areas.
-
Product
4 Port Phone Line Simulator (FXS) Adv
SIM-4FXS-A
-
This unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
Basic Basic Butt Set For Phone Line Testing
BSX200
-
Triplett Test Equipment & Tools
BSX200 Basic Butt Set is designed for people who occasionally need to deal with dial tone but don't require all of the features of an expensive model. The BSX200 provides user with dial tone, dial out, Caller ID, last number redial, on/off hangup button, flash button, DTM and FSK support, and three ways to connect to the line: an RJ11 connector, high quality alligator clips, and a type 66 adapter.
-
Product
Mini Lan Cable Tester
MT-7058
-
Complies with CE safety standardAutomatically detect good connections, opens, crossed wires & split pairsTest RJ45 TIA568A/B (AT&T) 258A), 10 Base-T, Token ring, RJ-11/RJ-12 USOC and coaxial BNC cablePin to pin cable map indicatorNon-contact voltage detection for user safetyTraces wires with tone & remote lights allows one person operationCompact size and lightweight design for easy to carry aroundCircuit Protection for both units to ensure the testing qualityLow power consumption with auto power off function to preserve batteryLong cable test more than 300 meters
-
Product
LAN Cable Tester
PA-01D
-
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
Product
Cable ID & PoE Tester
PK-170 INNOTESTER PRO
-
INNOTESTER PRO combines the functions of a smart cable tester, network tester, port identifier and organizer with the capability to identify up to 100 cables run at a time, and 8 Test + ID remotes allows one person to test 8 cables run up to 600 meters. Tone mode, transmits 2 powerful tones for tracing inactive and active network cables on a Switch or HUB. More effectively tracing at patch panel, termination blocks or hidden within bundles.
-
Product
Digiair PRO
-
Frequency range of 45-860MHz.• The meter to use for easy Digital terrestial installations.• Very sensitive, easy to maximize weak and strong signals.• Signal level reads out in dBuV.• Presents one channel readout with high resolution or six channels.simultaneously or the complete spectrum.• Built in beeper (pitch tone) and maxhold function.• Aerial power output, 0, 5 and 12V.• Built in, rechargeable battery.• Power supply and car-charger enclosed.• Carrying-case enclosed.• Small and handy design.• Made in Sweden.
-
Product
Public Switch Telephone Network Tester
295B
-
The Testphone 295B is a test telephone designed for use on Public Switched Telephone Networks (PSTN). It is designed for use on both Dual-tone Multi-frequency (DTMF - tone dialling) and Loop Disconnect (LD - pulse dialling) lines. Fitted with an integral ADSL filter, the telephone will not cause interference when connected to ADSL/Broadband lines in either `on hook` or `off hook` mode.
-
Product
AMP HOUND 2
AMP2
-
*Attach adapter to fuse or touch probes to top of the fuse to measure automotive amperage instantly without removing the fuse*Audible tone lets you know when you have connection with a fuse and if there is current present in the circuit; perfect for working on under-the-dash fuse boxes*Snapshot Mode and Tracking Mode allow easy component testing and parasitic drain location
-
Product
Optical Fiber Identifier
TW3306
-
Techwin(China) Industry Co., Ltd
Optical Fiber Identifier TW3306Ais an essential installation and maintenance instrument. By inserting the fiber into its adapter head, it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.
-
Product
Professional Cable Tester/Tracer with Tone Generator
TC-NT2
-
The TC-NT2 is a convenient and comprehensive cable tester for network professionals. Its powerful and user-friendly features enable network installers to accurately check pin configurations of various voice and data communication cables. The TC-NT2 includes a master unit that transmits test signals to its corre-sponding remote terminator to verify cable reliability
-
Product
PSG Signal Generators
-
Generate trusted microwave signals: get metrology-grade frequency & level accuracy with excellent distortion & spurious characteristicsRely on the highest quality signals from pure CW tones with 1 W of power to complex, vector-modulated signals with 4 GHz bandwidthReduce the time you spend on signal creation with Signal Studio softwareTake advantage of increased performance, flexibility & speed when you replace a legacy source with the code-compatible PSG
