-
Product
Narrow Band Multiplier
-
*no mechanical tuners*fullband operation*planar design*bias voltage required
-
Product
C+L Band Broadband Light Source
S-103
-
ASE broadband source slot module of FOTS system can offer special function that is able to change optical output spectral feature variously, which is change optical output spectral feature variously, which is followed by user’s driving embedded pump LD freely. The output power of each pump LD is controlled separately by the program that is set up by user. In the case optimum ASE source output features such as wide broadband (> 80 nm @ -10 dBm/nm) and stable output power (< 0.02 dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. More stable application of ASE source is possible through the combination of monitoring of ASE output power, alarm status and pump LD status with real-time optimal feedback. The embedded FPGA processor makes high speed control possible and enables monitoring and feedback routine operated stably.
-
Product
X Band Coupler With Dual Output Threshold Detector
-
The X Band coupler with dual output has an input power range of either -5 to +10 dBm, or +5 to +20 dBm. Covering 8.0 to 9.5 GHz, insertion loss is less than 1.0 dB and VSWR is 1.5:1. The coupler/detector has two external resistors providing independently settable threshold TTL outputs. The power flatness is ~0.4 dB and hysteresis is 0.1 dB. Cougar can provide this function in other frequency ranges and input power ranges.
-
Product
L Band Splitter, DC Block All Ports
PD5142
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
Product
Portable Dual Band ADS-B Traffic and Weather Receiver
DYNON DRX
-
The DRX is Dynon’s new, affordable ADS-B traffic and weather receiver that fits in your pocket and can last all weekend on a single charge. DRX supports connectivity with most mobile aviation apps, including Foreflight and FlyQ, for superior in-flight situational awareness. See the entire traffic picture with dual band ADS-B reception and receive ADS-B in-cockpit weather products such as NEXRAD Radar, METARS, TAFs, and more. DRX also provides WAAS GPS position to your mobile device and has auto-dimming status lights for night flight. And as usual, the DRX carries on the Dynon tradition of bringing affordable, high quality avionics to all pilots. It’s list price is only $395, but pilots may find it at dealers as low as $349.
-
Product
Octave Band Analyzer
-
Octave Band Analysis and AnalyzerOctave band analysis is an indispensable tool for sound measurement because it gives a close approximation of how the human ear responds. Dewesoft octave band analyzer meets all of the IEC and ANSI specifications for octave filters.
-
Product
CATV Return Band Two Carrier Generator
PC-2
-
The PC-2 is a compact, temperature-stable two RF-carrier source. It is designed to be used for activating and testing the return-band. When used with a signal level meter, the PC-2 assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method.
-
Product
Universal Band Decoder
Bandmaster III
-
The Bandmaster III universal band decoder is a highly integrated unit that not only decodes band information using YAESU “band data” (note 1), but can sense band information for all bands from160M through 6M, including 160M, separate 80M and 75M, 60M, WARC bands and 6M by monitoring CAT (note 2) data going to and from the radio. The Bandmaster III also contains all circuitry for level conversion thus eliminating the need for a separate CAT radio interface (note 3).
-
Product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
-
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
Product
Amplifier Systems Band Specific
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Rack Mount, 1U, Switchable Dual 2x4/1x8, LL/UL/S Bands, Programmable Amplitude Balance
LS-16A-R1-24SLUS
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
Narrow Band Filters (Single Octave)
MINI-SMT® Series
-
The new MINI-SMT™ tunable filter advances our popular MINI-POLE® Series by providing Surface Mount (SMT) capability along with the field proven RF power handling, low distortion and exceptional selectivity performance of our MINI-POLE® filters. MINI-SMT™ bandpass options are available from 700 MHz to 3 GHz.
-
Product
Low Noise Dual Band VCO
-
This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.
-
Product
Full Band Phase Shifters
STP-18-10-M2
-
Full band phase shifters are micrometer-driven, waveguide-based phase shifters. The configuration of the micrometer-driven phase shifters is similar to that of level setting attenuators, where the phase shifting is caused by an E-plane dielectric insert in the rectangular waveguide. The amount of phase shifting is directly dependent on the volume of the insert. The VSWR and the insertion loss of these phase shifters are dependent on the frequency. The below standard offering covers the frequency range of 18 to 110 GHz and a phase shifting range of 180 degrees. These micrometer-driven phase shifters are typically used to introduce a certain amount of phase shifting when the absolute number is not a focus.
-
Product
Narrow Band Filters (Single Octave)
NANO-POLE® Series
-
The NANO-POLE® is designed for optimal size, DC consumption, RF power handling, insertion loss, signal purity and linearity. The NANO-POLE® provides a minimum center frequency step size of 10 MHz typically but can be modified based upon request. The NANO-POLE® requires a +3.0 V supply that typically draws 5 mA when not hopping. The supply voltage should be adequately filtered as noise present on this pin will influence the RF signal purity. The NANO-POLE® uses SPI control interface.
-
Product
2 Vertical Multi Band Phase System
W9AD
-
The system will produce a broadside pattern and an end fire pattern figure 8 as well as other lobes and nulls in the various directions as you change the combinations. One should model this antenna using EZNEC or some other antenna modeling program to determine the patterns which are available to the user on all bands of use.
-
Product
Narrow Band Digital Signal Delay Lines
-
Advanced Science and Novel Technology, Co., Inc.
Narrowband (11GHz-17GHz) tunable clock phase shifterDelay adjustment range of 140psExhibits low jitter and limited temperature variation over industrial temperature range100MHz of bandwidth for the phase adjustment tuning portsIdeal for high speed proof-of-concept prototypingFully differential CML input interfacesFully differential CML output interface with 800mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 0.91WFabricated in SiGe for high performance, yield, and reliabilityStandard MLF/QFN 24-pin package
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
L Band Splitter, DC Block All Ports
PD5062
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
Wide Band Filters (multi-octave)
GEN3-ERF®
-
The 3rd Generation Mini-ERF is a Reduced SWaP-C, 30 to 520 MHz tunable bandpass filter that features 50mW (typ.) power consumption, 1 Watt CW continuous power handling (7% BW), +40 dBm IIp3 (typ.), low insertion loss, and 4 dB typ. selectivity @ +/-10%, (7% filter). The GEN3-ERF’s are fully tuned and tested by Pole/Zero® for convenience and ease of use.
-
Product
L Band Splitter, DC Block All Ports
PD5022
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
Narrow Band Filters (Single Octave)
MINI-POLE® Series
-
The MINI-POLE® Series of tunable filters is optimized for size, RF power handling, low distortion, and exceptional selectivity. The product line includes several standard designs in various bands to support a myriad of applications. Approximate performance is summarized in the MINI-POLE Series Selection Guide.
-
Product
L Band Splitter, DC Block All Ports
PD5082
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
Wireless Measurement System for ETSI & FCC Devices for ISM Bands
TS8997
-
The R&S®OSP-B157W8 PLUS 7.5 GHz module with up to eight channels is the core of the system and uses a printed RF switch board in solid-state relay (SSR) architecture. It allows flexible operation of the connected DUT (up to eight ports) for power measurements, signal conditioning via the integrated attenuators, couplers and combiners, RF switching to the measuring instruments in combination with the R&S®OSP-B157WX up to 40 GHz and is controlled by R&S®WMS32 software.
-
Product
Dual Band Radiometer
UVS-AB-T
-
The UVS-AB-T measures UV-A irradiance and UV-B irradiance.The dual band UVS-AB-T measures the irradiance in two spectral bands with a single sensor providing separate outputs for each band
-
Product
L Band Splitter, DC Block All Ports
PD5032
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
C/L-Band ASE Light Source
ASE7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ASE7000 series is C/L-Band ASE light source with featured with high stability and high output. It is mainly applied for testing of C/L-Band optical components and optical communication equipments as well as Fiber Optical Sensor etc. Huatai ASE7000 has three types of exterior structure, suitable for different customer’ requirements.
-
Product
DBAir Safety Managers Noise Meter System With Octave Bands
06NK103
-
This Sound Level Meter System with Octave Bands is the ideal system for the professional Health and Safety Manager with occupational noise monitoring duties.
-
Product
Polarization Maintaining Band Pass Filter
-
Zhongke Rayzer Optical Technology Co.,Ltd
Selects the thin film filter withgood performance to ensure the high quality opticalperformance, stability and reliability. It is uses to shieldnoise signal in EDFA and fiber laser system. It has thecharacteristics of high isolation, low insertion loss, highreturn loss and high power.
-
Product
L Band Splitter, DC Block All Ports
PD5132
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
