Custom Fixtures
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
-
Product
ARINC HSI / ADI Test Fixture
TA-2000
-
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
Product
Grips and Fixtures for Force Gauges
-
AMETEK Sensors, Test & Calibration
We supply a range of grips and fixtures for the Chatillon force gauges. Below you will find a selection of our most popular grips and fixtures. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
Product
Test Fixture Adapters for In-Circuit Test Fixtures
-
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
Custom Cable Assemblies
-
AMETEK Power Instruments has designed and manufactured electrical, thermocouple, and fiber optic harness assemblies for more than sixty years. We have the experience and capability to produce rigid and flexible harness assemblies for virtually any application, whether it is a missile ignition assembly, aircraft actuator assembly or a thermocouple harness for an industrial gas turbine. AMETEK Cable & Harness Products boast superior reliability, high temperature operation, numerous braiding options for abrasion resistance and EMI shielding, waterproof or environmentally sealed, and custom molding. For more information, please contact us.
-
-
Product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
-
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
Product
Custom Solar Simulation
-
Atlas Material Testing Solutions
Solar heat load effects are critical with respect to product functionality, operational performance, thermal management, noise and dimensional stability. Therefore, any new product made from different materials and components should be tested under solar environmental conditions representative of those locations in which it will exist - anywhere ranging from the heat of the Australian Outback to the frigid climate of arctic regions.
-
Product
Customized Testing Machine
-
Jinan Scientific Test Technology Co. LTD.
Customized Testing Machine
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
Test Fixtures
-
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
-
Product
System Test Fixture
-
Chassis Level Test Fixture, Set Box Test Fixture, and more by IST Engineering
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 250 mm (wxd)
CMCSK-03-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Custom Sensing And Imaging Solutions
-
Micro Magnetics has a proven track record of excellence in designing and developing new products and solutions based on our knowledge of magnetic devices and materials. We offer specialized solutions to meet our customers? unique needs. These solutions include single magnetic sensors, sensor arrays, custom electronics and packaging solutions, sensor processing (polishing, dicing, and lapping), and custom film and device deposition.
-
Product
MMI-HV, Mechanical Test Fixture
100182
-
Mechanical test fixture with optimized ergonomics for function test, final test and ICT applications. The MMI is prepared for both safety switches with guard locking and electrical interlocking. Our test fixture is versatile.
-
Product
Test Fixture and Test Programing
-
Landrex Technologies Co., Ltd.
Test Fixture and Test Programing
-
-
Product
Mach Airspeed Test Fixture
TA-6055A
-
The TA-6055A is a Mach Airspeed Test Fixture built to support the testing and repair of the 2082 and 2083 series of Servoed Mach Airspeed Indicators (SMASI) used in some Boeing aircraft. These mach airspeeds are synchro driven and require a coarse and fine input for altitude and a third input for airspeed. This test fixture was designed around the test procedure and is interfaced with our TA-1001 panel which provides for two of the synchro sources and two Angle Position Indicators (API).
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 335 x 250 mm (wxd)
CMK-02
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
CXM Custom Chassis
Chassis
Cytec can manufacture custom microwave systems to your specifications. Need to build a switch with 6 different styles of relays? Want to combine relays, amps, splitters and couplers? Need to combine parts from 8 different vendors to meet the specs you want?
-
Product
Custom Reed Relays from Pickering Electronics
-
Pickering Electronics manufactures hundreds of model relays. Many of these custom reed relays are minor variations of a standard part, for example, a different test specification or pin configuration. Others are custom designed to meet our customer's particular requirements.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 450 x 330 mm (wxd)
CMCSK-07-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Special / Customer Spec. Crates
6U VME64x 6023 JLAB Crates
-
For the Thomas Jefferson National Accelerator Facility (JLAB) in Virginia (USA), a special version of the VME 6023 crate series with front to rear air-cooling was developed. “JLAB style” VME crates are available with standard VME/VME64 backplane and mechanics as well as with VME64x or VXS (see VXS section) backplane and IEEE 1101.10 compatible mechanics, (enhanced EMC and ESD shielding).
-
Product
Custom Gauging
-
As the world’s leading bore gauge manufacturer, Bowers Group has also earned a reputation for manufacturing custom heads for non-standard applications.
-
Product
Drop-In Functional Test Fixtures
-
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
Product
Custom Cable Constructions
-
Teledyne Marine Cable Solutions
Cables purpose-designed for challenging applications. Choose from a menu of conductors, constructions, and jacket options to create a solution that provides reliable connectivity in situations with harsh weather or chemicals, abusive handling, or mechanical stresses.
-
Product
Custom Environmental Test Chambers
-
Does your environmental testing conditions have special requirements, or are you unsure of the right product for you? Tenney and Lunaire Environmental offer custom environmental test chambers - including custom climate chambers and custom vacuum chambers. The experienced Tenney and Lunaire team can provide customizations to their climatic chamber models based on client needs. Contact the sales team today to discuss you specific testing requirements.
-
Product
Clamshell Type Mechanical Fixtures
Series 10
-
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
