Radio Test Sets
See Also: TPS
-
product
5G Radio Test Set
Operating from 20 to 40 GHz, two radios may be connected to the system allowing full duplex operation. Each radio may operates over identical Air Interface with uni or bi-directional multipath. The delays between radios may be varied from 0 to 1 mile in 5 foot steps with propagation loss control. The 2040+ creates a variable test range right in your lab. It can be used as a design aid and as a test tool for new modulation and encryption schemes prior to expensive and time consuming field testing.
-
product
Radio Test Set
CTS-6000 Series
Bring your radio test function into the modern age with the new CTS-6000 Series radio test set. Combining nineinstruments into one, this tester offers fault detection and operational verification of your radio communicationssystem whether in the factory, at the depot, or deployed in the field.
-
product
Universal Radio Test Set for FM and AM Radio Stations of the VHF Band
RST-430
RST - 430 Radio-Communication Service Tester is designed for maintenance and repair of FM and AM radio stations operating in the HF and VHF bands. It is a multipurpose radio measuring device for maintenance of communication equipment in indoor and field conditions.
-
product
Tactical Radio Test Set
CTS-6100
The CTS-6100 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
product
Radio Test Set
CMA180
With its frequency range from 100 kHz to 3 GHz, the R&S®CMA180 is ideal for testing all common analog and digital radio systems. Input levels up to 150 W are no problem for the R&S®CMA180. The flexible internal switching capabilities for the audio and RF paths make the R&S®CMA180 suitable for a wide range of test requirements. Users can configure the internal generators, external audio sources, filters and measurements according to the given application. In the predefined test scenarios for receiver, transmitter and duplex tests, the RF and audio paths are preconfigured. This saves time and eliminates configuration errors for standard test cases.
-
product
Radio Frequency, Communications, & Navigation Test Systems
Reduce testing time and costs with the Astronics radio test sets for use in military, avionics, and civil security industries.Available in commercial and military grades, these integrated test systems make it easy to develop test program sets and leverage them securely and instantly across all deployed testers at the factory, depot, and operational levels.
-
product
NI Automated Test Software Suite
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
product
Infotainment Test for Automotive Applications
Multimedia operating interfaces are complex control and display devices for functions such as entertainment, telephony, on-board computers and vehicle settings. The functional test of such complex control units and their networking within the vehicle architecture presents a particular challenge in every phase of the product design process.
-
product
Design for Testability (DFT Test)
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
-
product
Imperial Test Executive
ITE
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
product
Test Management Software
ActivATE™
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
product
Application Software for Electronic Test & Instrumentation
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
product
Semiconductors Testing
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
High Speed Test Bench
AT444
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
product
Environmental Control System Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
product
Bottom Electrode SMD Test Fixture
16198A
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
product
Modular Functional Testing Platform
OTP2
Functional testing is an important part of product development and manufacturing and is used to ensure quality, performance and reliability from launch to end of life. A modern, future-proof functional test system must meet many criteria in order to meet the ever-growing demands of the industry. The OTP 2 open test platform developed by LXinstruments meets the following requirements for a dynamic and highly competitive market.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Bluetooth RF Test System
FRVS
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
product
Lens Module Test Platform
The Lens Module Test Platform is a flexible solution to deliver the quality that is expected from your brand for all types of lenses and cameras. The system can be configured to measure objective, eyepiece or camera lenses. As the platform can efficiently measure lenses as small as 2 mm3, it is perfect for the critically precise applications of life sciences, consumer electronics, automotive and other industries. With 25+ years of quality experience, the Lens Module Test Platform ensures that all products shipped to market work as intended.
-
product
GSM/EDGE Analysis Using NI PXI RF Test Instruments
NI-RFmx GSM/EDGE
The NI-RFmx GSM/EDGE personality is a highly optimized API for performing physical layer measurements on GSM/EDGE cellular standard signals. NI-RFmx GSM/EDGE is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
product
RSE Wireless EMC Spurious Emission
TS8996
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
product
Electronic Control Unit Functional Test
End-of-line tests are critical to ensure passenger safety in the era of smarter vehicles. A flexible test solution is needed to ensure extensive test coverage and high test throughput with a low total cost of ownership.
-
product
PCIe 2.0 Test Platform
PXP-100B
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
product
NI Semiconductor Test Systems
The STS delivers the openness and flexibility of the NI PXI platform to the semiconductor production environment. For easy integration into the production test cell, the STS comes with features such as handler/prober integration, spring probe device under test interfacing, STDF data reporting, and system calibration.
-
product
3-Axis Non-Robotic Automated Testing System
AT3
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
product
Automated Test Equipment
These systems test semiconductor performance and quality with industry-leading precision and cost efficiency. Robust support for semiconductor design evaluation, volume production ramps, and yield improvement.
-
product
NI Real-Time Test Cell Reference System
778820-35
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
