Flaw Detectors
See Also: Flaw Detection, Ultrasonic Flaw Detectors
-
product
Scintillation Radiation Detectors
ORTEC offers a variety of scintillation based radiation detector solutions including Thallium-activated sodium iodide [NaI(Tl)] and Lanthanum Bromide [LaBr3(Ce)].
-
product
IR Detectors
IR detectors have been a part of our standard product range at LASER COMPONENTS for almost three decades. A distinction is made between sensors for the near infrared range (NIR) from 1.0 µm to 2.5 µm and those for the mid-infrared range (MIR) above 2.5 µm. IR detectors of all modes of operation are a part of our product portfolio and leave nothing to be desired.
-
product
Ultrasonic Leak Detector
ULD-420
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
product
Conveyor HotSpot Detectors
The transportation of coal on any form of conveyor system has the potential to ignite, with the ultimate outcome being a fire. A single point temperature measurement system can detect a hot spot, but is just as often likely to miss one.
-
product
Leak Detectors
Leak Survey Tool is designed specifically for "water leak surveys" done by water departments, water districts, and other government and private agencies concerned about "unaccounted-for water losses." The LD-8 is a “rod-based” acoustic listening instrument for listening for water leaks at hydrants, meters, and valves:
-
product
Analog Ionizing Radiation Detectors
A great general purpose analog radiation detector. Detects from 0-50 mR/hr.
-
product
Broadband Detectors
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
product
Leak And Seal Strength Detector
LSD-02
Jinan Leading Instruments Co., Ltd.
LSD-02 Leakand Seal Strength Detector is applicable in the quantitative measurement of leak, heat seal strength, heat seal quality, and burst pressure of each heat sealedges of the flexible packages that are made using heat seal and adhesiveprocessing, as well as sterilized packages; the quantitative measurement ofleak performances of all kinds of plastic pilfer-proof closures; thequantitative measurement of the unitary airproof, compression resistancestrength, cap body joint strength, cap disengaging strength, seal strength ofedge and butting strength of various flexible tubes. It can also provideevaluation and analysis for the compression and burst resistance strength ofthe materials of flexible packaging bags, the torsional airproof index of cap,the cap joint and disengaging strength and the stress strength; as well as theairproof performances, the compression resistance performance and the burstresistance character of unitary bottle, etc.
-
product
Resistance Temperature Detectors
Sensors used to measure temperature by correlating the resistance of the RTD element with temperature.
-
-
product
Custom Detectors
Besides the described types Inphora can supply detector-filter combinations with parameters matching the customer's special requirement, with different sized housing, without housing. If the application determines the detector's spectral responsivity, we can achieve that with a filter designed exactly to the specifications. CCD cameras with unusual spectral sensitivity functions can be matched with filters to obtain CIE tristimulus response or photopic response. Similarly, photmultiplyers can be matched also with INPHORA filters. When determining parameters for a custom detector-filter combination several details have to be considered:
-
product
Millwatch Carbon Monoxide Detector
Advanced system giving early warning of potential fires by detecting tell-tale carbon monioxideSpecially designed for fire detection on mills and pulverizers for coal and biomassContinuous self-checking of measurement integrityTailored to each application/plantStandard analog and discrete contact outputs
-
product
Zero Bias Schottky Detectors
KRYTAR Zero Bias Schottky Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
product
Fixed Flame Detectors
Teledyne Gas & Flame Detection
Would you like to source high-performance flame detectors? Teledyne Gas and Flame Detection offers detection solutions that precisely meet the needs of the most demanding professionals.
-
product
Solar EL Defect Detector
Jiangsu Keyland Laser Technology Co., Ltd.
Features: - Reveals invisible defects- Improves line yield prior to lamination- Improves quality and reliability of final product- Exceptional optical resolution in its class- Flexible system configuration for framed or unframed modules testing
-
product
Directional Detectors
KRYTAR offers the industry's widest selection of Directional Detectors specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications. Complete engineering services for custom designs that meet or exceed critical performance and/or packaging specifications are available.
-
-
product
Low Voltage Detectors
LVD-17
Standard Electric Works Co., Ltd
● Microprocessor-controlled smart voltage detector.● Bright LED and audible alarm sound when voltage is present.● Designed for non-contact voltage detection.● Sensitivity adjustable with thumbwheel.● Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits.● LED indication for battery condition.● Identify Hot and Neutral.
-
product
RF Detectors for Millimeter Wave
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
-
product
Probes, Cables & Detectors
Probe has a mica window that has a thickness of 1.8 to 2.0 mg/cm2. This allows detection of alpha radiation as low as 3.0 MeV when in close proximity to the window. Beta radiation in excess of 35 keV and X-ray or gamma radiation greater than 6 keV can also be deteched. The detector is provided with a BNC connector. It can be used with most count rate and survey meters which accept Geiger Mueller (GM) detectors operating at 900V DC.
-
product
Radiometric Detectors - Clinical
Designed for use in regulated environments. It comes with 5 or 10 detectors (each with 550-sample capacity), and 5 and 10 detectors (each with 1,000-sample capacity).
-
product
Chatter Detector
Trig-Tek™ 850A/B
The Trig-Tek™ 850A/B Contact Chatter Detector provides a means of monitoring the continuity of switch or relay contacts while being subjected to environmental stress. 10 channels Adjustable time interval (1μs to 999 ms) Individual fault light and fault latch per channel Open or closed contact detection
-
product
Non-Contact Voltage Detector
VOLTCHEK
The VOLTCHEK is a variable non-contact voltage detector, A proximity device which detects the presence of an alternating electric or electromagnetic field. It is used by industry professionals for live or dead voltage determination of outdoor overhead or underground at URD test points. Firstly as a proximity device to determine live or dead situations and then as a touch device to verify the source has physically reached the zero AC field. This is the only equipment capable of testing all voltage from AC 415V to 765kV from a distance, beyond arcing zone.
-
product
CO Detector
6602
Peaceful Thriving Enterprise Co Ltd
This detector is design to detect the concentration of CO within the environment. The concentration of CO will be indicated by LED and buzzer voice. It's a helpful appliance for home, room and factory detection.
-
product
Radar Detectors
histler''s FDSR (Field Disturbance Sensor Rejection), the most recent advancement to combat new vehicles equipped with Frequency-Modulated Continuous Wave (FMCW) K band blind spot and collision avoidance devices that clutter nearly all of K band causing a normal radar detector to alert continuously.
-
product
Remote Spectral Detector
CSS-45
The CSS-45 detector incorporates a powerful microprocessor which performs not only data acquisition but also all necessary lighting calculations. Both USB 2.0 and RS 485 interfaces are standard enabling the flexible configuration of single and multi-detector based systems. An optional software development kit supports integration into third party application software. With its wide spectral range from 360 nm to 830 nm the CSS-45 is ideal, for example, as a high accuracy photometric and colorimetric detector (according to CIE S023).
-
product
Burst Detectors
The Burst detector monitors interference threshold exceedances at cable-and line bundles. It selectively detects conducted disturbances, which would influence the monitored device.
-
product
Carbon Monoxide Detectors for Aviation
AV8 Inspector Collection
The Sensorcon AV8 Inspector is a portable, professional-grade Carbon Monoxide monitor designed for aviation enthusiasts and professionals including pilots, ground crew, technicians and inspectors.
-
product
Fixed Gas Detectors
DG7 Series
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
product
Infrared Gas Detector
SMC 5100-28-IT
The SMC 5100-28-IT detector uses infrared technology, an accurate and stable gas detection method that is low maintenance and can operate in highly combustible and/or low oxygen environments.
