Serial I/O
Sequential input and output of data.
-
Product
PCI Express Digital I/O Cards With Counters And COS Detection
PCIe-DIO-24DCS, PCIe-DIO-24DC, PCIe-DIO-24DS, and PCIe-DIO-24D,
-
This product is a x1 lane PCIe DIO board available in four models ranging from basic DIO to advanced COS detection and Counter/Timer capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
Product
PCI Multifunction I/O
626
-
6 versatile 24-bit counters for encoders/timers with interrupt generation Fail-safe Digital I/O E-stop Relay Battery backup of counters Four 14-bit D/A outputs, 20 Khz update rate Sixteen 16-bit differential A/D inputs, 15 kHz rate Watchdog timer may be used to reset PCI bus 48 bi-directional digital signals for solid state relay boards, 40 with edge detection and interrupts
-
Product
LVDS Digital I/O with Kintex UltraScale FPGA - XMC
Model 71810
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex Ultrascale FPGAs- Front panel digital I/O can be used as a status and control or data interface- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
Product
PCI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, Digital I/O Device
778833-01
-
The PCI-6528 is an industrial, parallel digital I/O interface.With programmable power-up states, you can configure the initial output states in software, to ensure safe … operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
3U CompactPCI Serial Intel® Xeon® W Processor Blade
cPCI-A3535 Series
-
- Intel® Xeon® W-11555MRE 6-Core processor- Max. 64GB DDR4-3200 by 2x SODIMMs- 80GB 3D Nand flash SSD in SLC mode- USB 3.2, USB-C and RJ-45 iAMT front panel service ports- 2x M12 2.5GbE front panel ports for on train use
-
Product
I/O Connectivity
-
I/O modules are installed into your real-time target machine and come with Simulink driver blocks and full documentation. The majority also include a set of I/O cables and terminal boards.
-
Product
4DI/4Relay 2.4G WiFi IoT Wireless I/O
WISE-4060
-
Supports IEEE 802.11 a/b/g/n (2.4GHz)Supported protocols: Modbus/TCP, TCP/IP, UDP, DHCP, HTTPs, MQTTStores 10,000+ data points locally with SNTP/RTC time sync and WDT auto connection recoverySupports RESTful web API in JSON format for IoT integrationWith UDP-based AES-128 encrypted wireless P2P, abnormal inputs can automatically trigger up to 16 WISE modules in the field
-
Product
Rugged Deployable, Rackmountable Chassis For 3U Cards Aligned To SOSA Or CPCI Serial
20037765
-
This unit is a rack-mountable, rugged deployable chassis for use in harsh environments. The chassis has been designed to provide modularity and flexibility to support the full design life cycle of a system from initial concept and lab development through to qualification and full platform deployment.
-
Product
Serial To Digital Interface MiniBox™
-
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
Product
12-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-16
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
Type 15, CompactPCI Serial, 9 Slots, SSL, 4U, 63HP, 294mm
047-711
-
CompactPCI Serial System Type 15 with 9 Slots: 8x CompactPCI-S.0. Peripheral Slots and 1x CompactPCI-S.0. System Slot on the left side of the system platform. 2x 300W pluggable, air-cooled mit fan tray and powder coated.
-
Product
Configurable CAN FD Module With A Focus On Analog I/Os
PCAN MicroMod FD Analog 1
-
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The motherboard PCAN-MicroMod FD Analog 1 focuses on analog inputs and outputs, which are provided with the appropriate protective circuit.
-
Product
32-CH EtherCAT I/O Terminal Base For M-Type Modules
ECAT-TB32-M-DIN
-
The ECAT-TB32-M-DIN is a 32-channel EtherCAT I/O Terminal Base designed specifically for ADLINK's M-Type EtherCAT IO Slave Modules. This terminal base unit serves as a foundational component for enabling communication and interaction with various peripheral devices through the EtherCAT protocol.
-
Product
3U CompactPCI Serial 9th Gen Intel Xeon®/Core™ i7 Processor Blade
cPCI-A3525 Series
-
CompactPCI® Serial (PICMG CPCI-S.0) is a new modular computer standard officially adopted by PICMG in 2011. The CompactPCI Serial standard defines a completely new connector to support high-speed serial interfaces including PCI Express, SATA, USB and Ethernet. A CompactPCI Serial backplane has six high-speed connectors P1 to P6 on the system slot but only P1 is mandatory on peripheral slots, P2 to P6 being optional. A CompactPCI Serial system can comprise a total of nine blades (one system blade and eight peripheral I/O blades) through an Ethernet full mesh or single star architecture. The CompactPCI® Serial standard is the next-generation of the CompactPCI® specification and provides more flexibility and higher speed and bandwidth in modular system solutions.
-
Product
IO Expander
AD16x2DA16x8-125ETH
-
The IO Expander is an additional module to provide more input and output capabilities to the AD16x2DA16x8-125ETH. Via high speed link it connects 8 TTL inputs, 16 TTL outputs, 8 SPDT RF switches, and a GPS module.
-
Product
CompactPCI® Serial MXM 3.0 Type B Graphics Module Carrier
SV2-MOVIE
-
3U Carrier for MXM 3.0 Type B graphics module, 4 x DisplayPort front panel connectors, installed PNY P5000 MXM, 192bit/GDDR5 16GB, 100W TDP 2048 CUDA Cores, 8HP heat sink.
-
Product
Automotive Serial Triggering and Analysis (CAN, LIN) for DSOX1000 Series Oscilloscopes
DSOX1AUTO
-
The automotive serial triggering and analysis (CAN, LIN) option for InfiniiVision 1000 X-Series oscilloscopes allows you to trigger on either standard or extended CAN message IDs, including the message ID of a remote transfer request frame. It supports triggering on a data frame and allows you to specify message IDs, data and data length for filtering messages of interest. Triggering on active error frames also is supported. In addition, it supports triggering on LIN frame IDs and data, and it includes color-coded parity and check sums errors. You can easily isolate serial packets to find error sources due to hardware or software related problems.
-
Product
PCIe-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
786456-01
-
PCIe, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The PCIe-7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe-7846 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
IP-Parallel-IO
-
IP Compatible card with 48 programmable TTL IO or 24 - RS422 / RS485 compatible differential pairs. 5 mixed combinations available. Filtered or direct input. Programmable interrupt from each IO [TTL or differential]. 2 counter timers. Waveform generator.
-
Product
3U CompactPCI 5-Port Serial Ethernet, Optional POE Card
cPCI-A3ETH
-
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP- 5x RJ-45 ports support up to 2.5G via Intel® i226IT Ethernet controllers- Optional PoE supported- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
16DO IoT Modbus/SNMP/MQTT 2-Ports Ethernet Remote I/O
ADAM-6256
-
16ch digital output(pulse output)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful,ASCIIGCL to perform basic logic control rulesCloud access: Data update to AzureAuto-bypass function to ensure daisy-chain data transmissionPeer-to-Peer function to map I/O statusBuilt-in web serverWatchdog timer to recover the system
-
Product
3U CompactPCI Serial 4-slot SSR w/ RTM w/ Ethernet
1CPCIS-304-R210
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot right, with rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, with connectors for Rear Transition Modules (RTMs) in slots 1 to 3, Ethernet full mesh.
-
Product
3U CompactPCI Serial 4-Port USB 3.2/2-Port Ethernet Card
cPCI-A3USB
-
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 4x USB3.2 Gen 1 ports and 2x RJ45 2.5G LAN ports in front panel- 1x USB2.0 port on board- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
PCI Digital I/O Cards
-
Sealevel PCI digital I/O cards are available with optically isolated inputs and Reed relay outputs. For high-voltage requirements, TTL versions provide convenient connections to industry-standard solid-state relay racks. Sealevel low profile PCI digital I/O boards meet the requirement for the MD1 low profile specification and feature Universal Bus (3.3V and 5V) for compatibility with both new and legacy computer systems.
-
Product
I/O Board With One GbE LAN, VGA And DC Jack For PICO841, PICO843
AX93267
-
*Specifications: 1 x DC jack, 1 x VGA, 1 x Gigabit LAN*Dimensions: 100 x 26 mm*Compliant products: PICO841, PICO843
-
Product
PCIe-6321, PCI Express, 16 AI (16-Bit, 250 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device
781044-01
-
PCI Express, 16 AI (16-Bit, 250 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6321 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6321 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Relay I/O Module via Ethernet
2650
-
8 form-C mechanical relays with 240VAC, 2A ratingConnects to an Ethernet through 2601 hub100 mm DIN carrierResponds to interlock and E-stop circuitsWatchdog TimerCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
Product
EtherCAT IO MDevice PCIE Card
PCIE-1203IO
-
667MHz dual-core ARM processor2 x EtherCAT ports for 250/200us cycle timeUp to DI 1024 CH / DO 1024 CH / AI 128 CH / AO 128 CH IO ControlDiagnostics for fast error handling can trace command and error message
-
Product
6RTD Modbus RS-485 Remote I/O
ADAM-4015
-
6ch RTDProtocols:Modbus RTU,ASCIIWatch dog to recover the system3000VDC isolation protectionWiring burned-out detection function
-
Product
I/O Board
-
For more expansion and convenience, we offer a ready to use I/O boards which are specially designed for Pico-ITX SBCs.
