Masters
See Also: Slave, Master Jumpers
-
Product
CXA Signal Analyzer, Multi-touch, 9 kHz to 26.5 GHz
N9000B
Signal Analyzer
Master the essentials in signal characterization with the leading low-cost tool in signal analysis Perform cost-effective stimulus response measurements with the optional built-in tracking generator Add crucial functionality with X-Series measurement applications Enhance theory with practical skills when used with a training kit in your RF & microwave education lab
-
Product
I²C/SPI Interface Device
Interface
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Product
Pronto For Windows
-
Pronto for Windows is Outram’s full-featured Windows-based power quality software designed to extract data from the Outram Power Master family of data loggers and power quality analysers and present it graphically for analysis.
-
Product
CAMAC Controller With USB Interface
CC-USB
-
The CCUSB is a full-featured CAMAC Crate controller with integrated high speed USB-2 interface and full CAMAC dataway display. It supports Master and Slave operations with complete CAMAC arbitration as well as auxiliary CAMAC controller operation.
-
Product
Raptor SL Primary Test Current Booster
-
The slave Raptor is visually identical to the master unit but lacks the amplifier, the handheld controller and the auxiliary input/output panels.
-
Product
Ethernet-based Distributed Systems
DMC-3425
-
The DMC-3425 is the first product in Galil's new E-Series line designed specifically for Ethernet-based distributed systems. The DMC-3425 provides a highly versatile and powerful form of distributed control where multiple DMC-3425 controllers are linked together. When linked, one DMC-3425 is designated as the master over the other DMC-3425 controllers in the distributed system.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
SMT Rework Station
RW1210
-
Safely and precisely rework SMD, BGA, or LED chips. This all-in-one solution covers rework needs for even the most complex, densely populated PCBAs. Yet it is easy to use, enabling technicians to quickly master delicate alignment, placement, and heating controls.
-
Product
Free Space Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
Bit Error Ratio Testers
-
Keysight’s bit error ratio test (BERT) system enables the most accurate physical-layer design verification of high-speed communication and multi-gigabit digital interfaces. Our expert-level support will help you select the high-performance hardware, control software, receiver test, and automation tools needed to help you master your design.
-
Product
AeroEngine Test Cells
-
A tec is a leading provider of jet engine test cells and flight component support. We provide our customers with high quality, superior value maintenance facilities and equipment for the testing of all types of turbine engines. We excel in both the design and construction of new facilities and the technological refreshment and sustainment of legacy systems. The Atec companies operate worldwide with new test cells, test cell modifications, engine test adapters, ADAQ™ control systems, support equipment, test benches, utilities subsystems, site surveys, repairs and training, and Master Service Agreements (MSAs).
-
Product
Mark II Dual Setpoint Monitor
95006
-
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
Product
Fuse Saver Master Kit
#8016
-
Innovative Products of America
The Fuse Saver provides a fast and safe solution to the old methods of "smoke testing" a short. This all inclusive kit includes a durable custom blow molded case. With the Fuse Saver you can move about your vehicle while checking for shorts in the electrical system.
-
Product
PXIe-8522, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module
787312-01
Ethernet Interface
PXIe, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8522 is a 1000BASE-T1 unshielded twisted pair (UTP) module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications that require Automotive Ethernet to test … and validate automotive electronic control units (ECUs). The PXIe-8522 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8522 also provides LEDs on the front panel to help you monitor the network link and activity.
-
Product
Wattmeter
PowerMaster II for SO2R
-
The Power Master II wattmeter has the ability to have two couplers connected to it, and it has provision to allow switching very easily between the two couplers through only two button presses on the front panel.When operating SO2R, you do not want to have to toggle from one coupler to another. We make matched couplers available for SO2R users and due to the nature of these couplers being high impedancedevices, we can actually connect the two coupler inputs in parallel and instead of toggling between the two couplers, they will both be connected and active at the same time. The first step is to disconnect all connections to the rear panel of your Power Master II and remove the two #6-32 philips screws on either side of the cabinet.
-
Product
VME to USB 3.0/Ethernet/Optical Link Bridge
VX4718
-
The VX4718 is CAEN New Bridge with enhanced data rate and extended interfacing capabilities, thanks to the on-board MPSoC (including an ARM processor running Linux). The board is a VME Master which can be controlled by an external PC via USB 3.0 and Gigabit Ethernet connections.
-
Product
VME to USB 3.0/Ethernet/Optical Link Bridge
V4718
-
The V4718 is CAEN New Bridge with enhanced data rate and extended interfacing capabilities, thanks to the on-board MPSoC (including an ARM processor running Linux). The board is a VME Master which can be controlled by an external PC via USB 3.0 and Gigabit Ethernet connections.
-
Product
Fiber Pigtailed Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
Secondary Master Oscillator
VCH-002
-
The secondary master oscillator (VZG) is designed to operate in a digital communication network as a synchronization equipment of the second level of the hierarchy. Its task is to track in phase one or more clock signals coming through the network from the synchronization equipment of the highest or equivalent level of the hierarchy.
-
Product
EOC Master
EOCM-793x
-
Hangzhou Softel Optic Co., Ltd.
EOCM-793x is an all-in-one EOC Master with EOC master module, ONU module and OR module. We can use one EOCM-793x to instead of three type products, HFC optical node, EPON ONU and EOC mater. It can reduce the number of active node in the system, decreasing failure rate and saving a space. It is the bestchoice of CATV, Internet and VOD for the operator.
-
Product
Modbus Simulator & Tester
Modbus Poll
-
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
Product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
Digital I/O
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Field Master 3 Electric Fence Charger
FM-3
-
Power to stop the most stubborn stock! For small to medium pastures. The all new low impedance model for small to medium pastures features advanced solid state circuitry. Shocks through wet weeds and brush. New color coded fence and ground terminals. Red to the fence and Black to ground. Fuse protection, with built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
Product
3U VPX Bus Extension Kit PCIe Gen. 3
-
A PCIexpress bus extension kit permits a standard desktop PC to expand its available PCIe slots and is used as a system master for control of a VPX chassis for industrial applications in measurement, control and testing.
-
Product
IO-Link Accessories/Connection Technology
-
- USB interface for connecting IO-Link enabled sensors to a PC- Bluetooth adapter for IO-Link sensors and masters- Repeater for increasing the range- Data splitter to integrate IO-Link sensors in old installations- Converter for converting standard signals to IO-Link and vice versa
-
Product
IO-Link
-
The IO-Link® interface simplifies communication to smart sensors and actuators, combining signaling with power-over-cable technology. It has become one of the key devices as industrial automation systems are growing more interconnected and intelligent to accommodate demands for centralized control and optimized production. Analog Devices implements both device PHY and master PHY interfaces (COM1/COM2/COM3). Designing with harsh industrial environments in mind, the master 4-port IO-Link power and communications interface, as well as the IO-Link transceivers featuring Integrated Step-Down Regulators and LDO with ±60V cable interface protection provide the required ruggedness. Optimum EMC performance is achieved with adjustable current limit and slew rate transmitters. Automatic wake-up request (WURQ) generation and an output supply current boosting capability for device startup are also available. Additional components integrate a 300 mA step-down (buck) regulator and a 150 mA LDO to supply all the power required for internal electronics in an connected sensor or actuator.
-
Product
PXI DeviceNet Interface Module
Interface
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
-
Product
Measuring Systems For Night Vision Systems
MTF Master IIT
-
Optik Elektronik Gerätetechnik GmbH
Measuring system for MTF, SNR and EBI of Image Intensifier Tubes (IIT). The MTF MASTER IIT was specially developed to classify the quality of image intensifier tubes by the objective criteria of the MTF (Modulation Transfer Function).
-
Product
Temperature Transmitter
SenseAir CO2
-
aSENSE is an advanced transmitter for installation in the climate zone. It measures both CO2 concentration and temperature. The data is transmitted to a BMS system or controller and can be configured with UIP Software. Detected values are transformed into two analogue output signals that can be transmitted to a system master or DDC. aSENSE is available both with and without LCD display for FIXED installation in the climate zone as well as in the ventilation duct.
-
Product
Test Kits
-
Optical Wavelength Laboratories
Deluxe color LCD fiber link certifier (includes MASTER and REMOTE devices) Tests two fibers at a time, cutting testing time in half (when compared to traditional fiber certification) Ideal for installers and contractors who need to certify fiber cables BI-DIRECTIONALLY Measure the end-to-end length of the fiber cable with every test Unlimited sets of job parametersOWLView software allows tri-report capability certification, OTDR, and endface all on one report) Multimode and singlemode options available.
