-
product
PXI 40Amp 14Volt 2xSPDT Automotive Relay
40-181-001
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
product
Modbus Simulator & Tester
Modbus Poll
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
product
PXI 5A Mux 8-Bank 5-Ch Isolated COM
40-651-014
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
PXI 8x4 1-Pole 10A Matrix With Loop-Thru
40-551-101
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, this module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. This version of the 40-551 may be expanded to larger matrix sizes using cabling to daisy-chain the X and Y signals Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
product
PXI 64 x SPDT Electromechanical Relays
40-148-201
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXI Single 16x4 1-Pole 5A Power Matrix
40-549-001
The 40-549 is a single pole power matrix module, suitable for switching inductive/capacitive loads up to 5A with 110VDC/250VAC hot switching and 400VDC/250VAC cold switching. It is available in single 16x4, single 8x8, dual 8x4 or single 8x4 configurations. Connections are made via a front panel 25 way D-type male connector. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. The module is suitable for applications requiring switching of either mains voltage or DC current.
-
product
PCI Express to VME Interface
SIS1100-E2/3104-2
The SIS1100-e2/SIS3104-2 interface/bus coupler is the choice for demanding VME readout applications. VME block tranfser speeds up to 160 MByte/s are readily accomplished in conjunction with state of the art VME slave hardware.
-
product
Digital Input Board
VME-1129
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
product
I²C/SPI Interface Device
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
product
16-CH Discrete Input 16-CH Discrete Output Module
HSL-DI16DO16-M-NN
- Input voltage: ±40 V (Max)- Output switching capacity: Single channel 500 mA; all channels 60 mA at 24 VDC- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ±10 mA (Max) , ±12.5 mA (Peak)- 16-CH digital input and 16-CH digital output. "NN" type for NPN sinking type sensor input or dry contact and NPN sinking type output- Slave ID consumption: 1
-
product
One Wire Communication Board
MS 1727
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
product
2-CH Pulse-Train Motion Control EtherCAT Module
EPS-7002
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
product
High Performance 335 M, 6 Channel Digital Receiver
DP-VME-5838
The DP- VME-5838 is a VME64x slave, high performance 335M, six channel Digital receiver card. It samples and down converts the analog IF signals into the digital base band data. The processed I/Q data are pulse compressed and decimated to the base band rate. In the Central Unit system, this pulse compressed I/Q data has to be sent to the signal processing unit through a 2.5G speed Optical SFPDP link.
-
product
12C Adapter Slave
USB I2C adapter MS
*Plug & Play*No additional driver necessary*HID device drivers are included in major operating systems*Open interface description enables communication without a DLL
-
product
Dynamic Digital I/O (3U), 32 Channel, 50 MHz
GX5291-50
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch. up to 50 MHz w/128MB On-Board Memory, 32-ch Domain.
-
product
USB I2C Adapter
MS (Master & Slave)
*Plug & Play*No additional driver necessary*HID device drivers are included in major operating systems*Open interface description enables communication without a DLL
-
product
PXI Multiplexer, Very High Power DC, 4-Channel, 20A, 28V
40-664A-002
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
product
PXI 20Amp 28Volt 2xSPST Automotive Relay
40-180-011
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
