Carriers
Carrier devices are practical for adapting your product to a standard interface for testing on the bench or in the chamber.
-
Product
Modulators / Demodulators
-
Mini-Circuits QPSK Modulator and I/Q Modulator / Demodulators are available in connectorized or surface mount packages up to 2000 MHz. These components provide excellent harmonic suppression as well as good carrier and sideband rejection while maintaining low conversion loss over the operating frequency band.
-
Product
5G NR Testing
-
5G NR is the first communications standard designed to support a wide variety of consumer and industry applications. 3GPP release 15 laid the foundation for 5G NR by introducing new, flexible numerology, advanced channel coding and modulation schemes. Enabling wider channel bandwidths and extended carrier aggregation schemes while also extending frequencies into the millimeterwave range make more radio resources available.
-
Product
CEP Stable Lasers And CEP Phase Stabilization
-
Carrier envelope phase stabilization (CEP) is an enabling technology for metrology and for the generation of few cycle pulses. As one of the pioneers in the field we have developed products that allow to stabilize the carrier envelope phase of light pulses of few cycle pulse oscillators and amplifiers.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781421-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Wideband RF Up Converter
150
-
The Wavefront family is built around a wideband quadrature modulator and broadband frequency synthesizer. The quadrature modulator features an extremely wide modulation bandwidth and operates over a very wide carrier frequency range. The on-board synthesizer features low phase noise and software controlled tuning across the full frequency range.
-
Product
4G Router
BB-SR30910020-SWH
Router
SmartFlex, Korea, 2x Ethernet, Wi-Fi, Metal, Without Accessories. LTE cat.4, 3G/HSPA+, GPRS/EDGE, Korea, 2x SIM - SKT carrier only (KT and LG U+ are not supported). LTE B1, B3, B5, B7, B8, B20, B38, B40, B41. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
5-Slot Desktop/Wallmount Chassis
IPC-6025
Chassis
5-Slot Desktop/Wallmount Chassis with Scalability for 5U Multi-system Solution. Front handle for easy withdraw in rackmount carrier, Lockable front door prevent unauthorized access.
-
Product
Network Traffic Visibility
-
Organisations and businesses are relying more on the network than ever before. In many instances, the network has become the business, such as is the case for managed service providers (MSPs), residential ISPs, mobile carriers, data centers, etc. Unfortunately, at the same time, networks have never been under this level of threat from malicious sources who want to disrupt or even damage infrastructure with various motivations.
-
Product
Rack Mounted Spectrum Analyzer
-
Designed for the measurement and analysis of communications and broadcast carriers, making uplink, down- link, L-Band carriers, IF, and 10MHz reference signals easy to measure, monitor, and store.
-
Product
PULSE IMPATT DIODES FROM 30 TO 140 GHz
-
Insight Product Company offers IMPATT diodes with pulse power up to 20 Watt and operational frequency range up to 140 GHz. Silicon p+-p-n-n+ IMPATT diodes are designed to be used in the millimeter wave oscillators and amplifiers. They are fabricated in the metal-ruby packages with hard-lead carrier (diameter 3.0 mm, 1.5 mm).
-
Product
FMC-LPC I/O Module
FM191
-
Sundance Multiprocessor Technology Ltd.
The FM191-RUA1 has a VITA57.1 FMC-LPC connector and follows the electronics specification and recommendations of the standard but is NOT form-factor compatible and will NOT fit all FMC carriers. Two versions are available. The FM191-R main features are a daughter card which provides 5V-TTL-compatible Analogue and Digital GPIOs that are suitable for robotics, motors and sensor application.
-
Product
cPCI to PMC Adapter / Carrier
cPCI2PMC
-
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
Product
Bi-Phase Modulators
-
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
Product
PCIE Module For PCIe Bus Expansion
PCI113
-
PCI113 is VadaTech second generation PCIe expansion module. The PCI113 is a high-speed 20Gbps bridge from the host PCIe bus to VadaTech’s carrier and Rear Transition Module (RTM) products such as the ATC104/114/118/117/119, ART114, μTCA chassis, etc. The different carriers host different I/O modules such as PMC/PrPMC, AMC, PCI-X and PCIe edge modules. This concept allows any of the available I/O modules in these standard form factors to be integrated quickly and easily into an AdvancedTCA or μTCA subsystem. The PCI113 allows expansion among multiple μTCA chassis or expansion into other chassis that are not ATCA or μTCA based.The PCI113 is a single module PCIE based on the PCISIG specification. The PCI113 provides a PCIe x4 link infiber/copper via front panel QSFP. The dual front I/O allows expansion into two separate systems independently. The upstream port must not have spread spectrum PCIe clock enabled.
-
Product
CompactPCI® Serial MXM 3.0 Type B Graphics Module Carrier
SV2-MOVIE
-
3U Carrier for MXM 3.0 Type B graphics module, 4 x DisplayPort front panel connectors, installed PNY P5000 MXM, 192bit/GDDR5 16GB, 100W TDP 2048 CUDA Cores, 8HP heat sink.
-
Product
Squid Carrier Board™ Family PCI Express Carrier Board for 8 MiniPCI Express Modules
SKU-085-01
-
Squid PCI Express Carrier board for MiniPCIe modules is the first product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 8 MiniPCI Express half or full-size MiniPCI Express modules to the one motherboard’s PCI Express slot.
-
Product
IP-Parallel-BA1 "IP-Tape"
-
The IndustryPack compatible IP-Tape design adds 48 digital parallel IO lines to one slot of your carrier board. The IO is dedicated to a DTC interface. Other interfaces can be implemented. The DTC interface has 22 Address, 16 Data plus Parity, 4 control and 5 status lines. Parity is automatically generated in write mode and checked in read mode.
-
Product
UHF True RMS Probe
-
The UHF True RMS Probe is a frequency compensated power probe capable of measuring power even in a multiple carrier installation. Regardless of physical waveform, the probe will measure the True RMS power of the signal. When used together with our Broadcast Power Monitor type 3024, you can add Web and SNMP capabilities to your mast site installation.
-
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781421-12
Matrix Switch Module
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
3U Format CompactPCI (CPCI) Bus IP Carrier
CPCI-SIP-2
Bus Extender
The CPCI-SIP is a 3U format CompactPCI (CPCI) bus IP carrier. The CPCI-SIP-2 provides mechanical support and the electrical interfaces for two single width IP modules, or a double width IP module. Multiple CPCI-SIP-2 boards may be installed in a single system.
-
Product
Modulation Analyzer
8201A
-
The Model 8201A provides precision modulation and audio analysis in a single, easy-to-operate package. Measures AM, FM, PM, carrier and audio frequencies, SINAD, distortion and carrier level.
-
Product
Amplitude Detectors
-
Amplitude detection, which eliminates the carrier (or the subcarrier) at the Doppler filter output
-
Product
4G Router
BB-SR30918120-SWH
Router
SmartFlex, Korea, 5x Ethernet, Wi-Fi, PoE PSE, Metal, Without Accessories. LTE cat.4, 3G/HSPA+, GPRS/EDGE, Korea, 2x SIM - SKT carrier only (KT and LG U+ are not supported). LTE B1, B3, B5, B7, B8, B20, B38, B40, B41. 2x Ethernet port with PoE support, DIN rail mounting.
-
Product
PXIe Module Carrier
HMPXI AXIe-1
-
The PXIe module carrier, HMPXI AXIe-1 Gen3 x4, is specifically designed to support PXIe modules in AXIe systems, allowing you to maximize the best of both standards in a single system. The HMPXI AXIe-1 carrier is designed as a single-slot AXIe-1 module and allows you to simultaneously install two single-slot PXIe modules.
-
Product
Flow Meter Sensor
RF Pickups
-
SPECTEC Innovative Sensor Solutions
SPECTEC RF pickups are excellent for applications that require near zero speed and zero magnetic drag sensing characteristics, such as flow meter sensor applications. SPECTEC RF (modulated carrier) sensors have a long history of use in turbine flow meters and turbine engines in the aerospace, petroleum, chemical, pharmaceutical and food industries.
-
Product
16 Bit DDS Generator Up To 200 MHz
96xx series
-
The 96xx series DDS generators deliver the highest performance in both speed and resolution. The series includes produts between one and 24 synchronous channels. DDS – Direct Digital Synthesis – is a method for generating sine waves from a single, fixed-frequency reference clock and is widely used in signal generation applications. The DDS functionality implemented on Spectrum Instrumentation’s AWG platform is based on the principle of adding multiple “DDS cores” to generate a mul?ti-carrier (multi-tone) signal, with each carrier having its own well-defined frequency, amplitude and phase. In addition to these static parameters, there are also build in dynamic parameters like frequency slope and amplitude slope to allow for intrinsic linear changes for multiple cores.
-
Product
PIM-Carrier-Dual
-
The PMC Carrier routes the PMC IO from P14/P24 to J3/J5. The PIM-Carrier-Dual routes the IO from J3/J5 to the two PIM positions. The PIMs route the IO to the bezel providing the equivalent of PMC front bezel IO on the rear of the chassis. The PIM can match the pinout of the front bezel IO to allow for common cables to be used for front and rear IO.
-
Product
3U CompactPCI Serial M.2/U.2/SATA Storage Carrier
cPCI-A3H20
Carrier Board
- 1x NVMe M.2 and 1x NVMe U.2 drive slot- 1x optional SATA 6Gb/s M.2 drive slot shared space with NVMe U.2- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Operating temperature: -40°C to +85°C with qualified modules- EN50155 compliant
-
Product
Transducers For Photodiodes
-
Photodiodes convert incoming electromagnetic radiation into electrical charge carriers. If photodiodes are short circuited an electrical current (photocurrent) proportional to the incident radiation intensity (number of photons per second) is induced. These photocurrents are generally small and cover the range from femtoampere (fA) to microampere (µA). Signal transducers transform this weak photocurrent to robust standard signals for reliable data transmission and simple data acquisition.
-
Product
Temporary Bonding Systems
-
Temporary bonding is an essential process to offer mechanical support for thin or to-be-thinned wafers, important for 3D ICs, power devices and FoWLP wafers, as well as for handling fragile substrates like compound semiconductors. A device wafer is bonded to a carrier wafer with the help of an intermediate temporary bonding adhesive, allowing the typically fragile device wafer to be processed with additional mechanical support. After the critical processes, the wafer stack is debonded. EVG’s outstanding bonding know-how is reflected in its temporary bonding equipment, which has been provided by the company since 2001.
