Bridge Amplifiers
Increase a transducers signal to measurable levels.
-
Product
SW Range Broadband Power Amplifiers 0.8 GHZ - 4 GHZ
SW Series
-
Class A solid stateBroadband (instantaneous single band): 0.8 GHz 4 GHzTypical output power : 18 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 13 W and H < -20 dBc up to 2.5 GHz andP1dB > 12 W and H < -20 dBc from 2.5 GHz to 4 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Product
16 Bit 250 KS/s ADC With 16 Channel Multifunction Digital I/Board And Bridge Signal Conditioner
-
The CP246 is a single-width, 6U, CompactPCI/PXI module with 8 channels of Bridge Signal Conditioning feeding 8 independent 16-bit Analog to Digital Converters (ADC). This single-width solution incorporates both signal conditioning and ADC to eliminate the need for complex field wiring.
-
Product
Four Quadrant Power Amplifier For Simulation Applicaton
PAV30000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Sample/Track and Hold Amplifiers
-
Analog Devices offers a portfolio of sample-and-hold amplifiers and track and hold amplifiers that combine speed with precision. ADI sample-and-hold amplifiers can acquire a signal in 700 ns and hold it with a droop rate of 0.01 µV/µs. These devices are up to 14-bit accurate, with low aperture jitter and output impedance, and they are available in commercial, industrial, and military temperature ranges.
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
Distribution Amplifiers
-
The Quartzlock range of distribution amplifiers are intended for use when multiple outputs from a single frequency standard/generator are required. This may be encountered in engineering labs, national standards labs, research and development, calibration labs and production. This is vital for the distribution of signals from other precision frequency standards like Hydrogen Masers, Cesium oscillators. For a technical discussion about distribution amplifiers go here or select a product range below.
-
Product
RGB Digital Fiberoptic Amplifier
CZ-V20 Series
-
SUPER HIGH POWER RGB sensor Industry's best color differentiation. High resolution amplifier for triple 16-bit calculation. New Luster Detection Sensor Head. Dual digital display & Direct access. New UV sensor head for fluorescent Detection. Three detection modes for every target [Super I / C' / C+I]
-
Product
Low Noise Amplifiers
-
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
Product
Amplifiers
-
Packaged and Die up to 26 GHzOver 145 MMIC Surface Mount and Die modelsConectorized models, power output to 100WHigh dynamic range, low noiseLow-cost, custom solutions available!
-
Product
Amplifier Module
LNAM-LPA
-
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
Product
IRIG Amplitude Modulated Time Code Distribution Amplifier
1205A / 1205A-MC
-
Precise Time and Frequency, Inc.
The ptf 1205A is a 12-channel IRIG amplitude modulated time code distribution amplifier housed in a 1U high, 19″ rack package. The ptf 1205A uses an RF design combining the latest technology in low noise components to minimize input/output delays which are of the order of nano seconds.The unit uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
Product
E-Band Low Noise Amplifier MMIC
AWL-7186
-
The AWL-7186 is a 4-stage ultra-low noise amplifier that provides a noise figure of less than 3.5 dB, an output P1dB of +8 dBm, and an adjustable gain range of 15 dB. The MMIC features exceptional gain flatness and superior noise performance over a very wide bandwidth. It is implemented in 0.1 um GaAs PHEMT technology.
-
Product
Separate Amplifier/Thin Amplifier Type Pressure Sensor
AP-C40W/V40W
-
New AP-C40K/V40W series digital air pressure sensor with the industries first wire-saving design system. Separate Amplifier/ Separate Thin Amplifier Type. World's most compact model with maximum character height. High resolution: 10x area focus function All-in-one I/O function
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
EYDFA Amplifier
-
a high-power, versatile amplifier designed for optical communication and other general-purpose Polarization Maintaining (PM) optical amplification applications. This compact module housing ideal for OEM integration applications.
-
Product
Measuring Amplifiers
VibroMatrix
-
The VibroMatrix measuring system consists of the USB measuring amplifier "InnoBeamer" and various software modules, which can be put together individually. Suitable for your measurement task. All you need is a computer or a notebook. The software enables you to measure in real time and record your data for later offline analysis in the office.
-
Product
Cable Fault Locator With Time Domain (Intelligent Bridge)
GT00ZD00ZY
-
GAOTek Cable Fault Locator with Time Domain has a reflectometer to locate faults in metallic cables and Intelligent bridge for tesing the broken line
-
Product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
-
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
Product
860MHz CATV Indoor Bi-directional Amplifier
-
Hangzhou Softel Optic Co., Ltd.
SA801H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network.
-
Product
SV Range Broadband Power Amplifiers 0.8 GHZ - 3.2 GHZ
SV Series
-
Class A solid stateBroadband (instantaneous single band): 80 MHz 1000 MHzTypical output power : 100 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 100 W and H < -20 dBc up to 450 MHz andP1dB > 65 W and H < -20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to MT 200 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
10mA One-Channel Amplifiers
-
USB connected devices have become common in lab environments. The nano box USB is a standalone piezo amplifier with 16 bit D/A resolution. Its small size and powerful amplifier includes a USB 2.0 interface that offers a variety of helpful commands.
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
Terminal Board
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
Power Amplifiers
-
Your ultimate solution for sound distribution in the contractor/install market.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
DT Range Broadband Power Amplifiers 10 KHZ - 1000 MHZ
DT Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 1000 MHzTypical output power : 25 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 20 W and H<-20 dBc up to 450 MHz andP1dB > 10 W and H<-20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
RF Amplifiers
-
Renesas provides a portfolio of RF amplifiers are designed for general purpose video and receiver applications.
-
Product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
-
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
