Wire
See Also: Contacts, Harness, Connectors
-
Product
Gauge Type T Thermocouple Wire
W-TW-20
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Ferrules, 1m, 90º
A1604FT-F-0A100
Cable Assembly
For applications where a 90 degree down cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
16 Bit 250 KS/s ADC With 16 Channel Multifunction Digital I/Board And Bridge Signal Conditioner
-
The CP246 is a single-width, 6U, CompactPCI/PXI module with 8 channels of Bridge Signal Conditioning feeding 8 independent 16-bit Analog to Digital Converters (ADC). This single-width solution incorporates both signal conditioning and ADC to eliminate the need for complex field wiring.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 1m
A025DM5-T-0A100
Cable Assembly
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Non-Linear Junction Detector
ORION™ HGO-4000
-
The ORION HGO-4000 is REI’s original high gain Non-Linear Junction Detector for special applications. The ORION HGO-4000 can locate listening devices and semiconductors in walls floors, ceilings, fixtures, furniture or containers and provides a user the capability to detect hidden electronic devices, regardless of whether the device is radiating, hard wired, or even turned off.
-
Product
Cable Assy 37-Pin D-Type F/F 1m
40-970-037-1m-FF
Cable Assembly
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21 AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products.
-
Product
PXI RTD Simulator Module, 4 Channel, PT500
40-263-502
Simulator
The 40-263-502 is a 4-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Wireless Ethernet Bridges
-
Our wireless Ethernet bridges connect your wired devices to a wireless network - explore our range of advanced solutions.
-
Product
Serial Device Servers
-
Connect and share RS-232 serial devices on wireless or wired Ethernet networks, with enterprise security support and multiple serial port modes for maximum flexibility in any environment.
-
Product
LAN Cable Tester PRO
PK-168 NextPRO S2
-
PK-168 is capable of wire mapping by pin & pair up to 600 meters,PK-168P: Remote unit come with PoE detector. It detects presence of PoE and displays type of PoE either end-span A or mid-span B or ultra power over 4 pairs and either 802.3af (PoE) or 802.3at (PoE+) is present.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 2m
A020GFR-C-0C200
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
Non-Linear Junction Detector
ORION™ 900 HX
-
The ORION 900 HX Non-Linear Junction Detector (NLJD) detects electronic semi-conductor components through dense materials such as bricks, concrete, and soil. The ORION 900 HX NLJD is made to detect and locate hidden cameras, microphones, and other electronic devices regardless of whether the surveillance device is radiating, hard wired, or turned off.
-
Product
AC Power Sources
MX Series
-
AMETEK Programmable Power, Inc.
The California Instruments MX Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the California Instruments MX series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the MX15, MX22.5, MX30, or MX45 unit to its designated location (using included casters), plug it in, and the MX series is ready to work for you.
-
Product
Test Adapter
cPCI/VME/VME64x
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A037DM5-C-HA050
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
CHEK 3-in-1 Electrical Tester
GT 3100GAM
-
Cable test monitors line continuity, shows completed circuits. Lamp test indicates the lamp and fixture continuity. Circuit tester checks if power is available, if polarity is correct, if wiring is correct.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 2m HV
A050DF5-050DF5-HA200
Cable Assembly
50- Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50- Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Ferrules, 1m
40-972-015-1m-FU
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Multi-Network Cable Tester
3PK-NT007N
-
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
Product
Cable Assembly, 26-Pin D-Type, Female To Unterminated With Ferrules, 1m
40-972-026-1m-FU
Cable Assembly
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks.
-
Product
Remote I/O
-
Reduces wiring costs, simplify troubleshooting and minimize downtime with Omron's high density I/O modules and other socket-based I/O products.
-
Product
Banana-Triax Adapter For 2‑Wire (Non-Kelvin) Connection
N1297A
-
The N1297 Series is a collection of banana-triax adapters for the Keysight B2900 Series precision source measure unit (SMU). It consists of both 2-wire as well as 4-wire connection requirements.
-
Product
Analog or Digital Communications Switching Systems with D Type Connectors
RS Series
-
The RS Series computer controlled switching systems are designed to switch multi-wire groups of signal up to 25 wires. These systems are typically used for signals such as parallel TTL, RS232, RS422, WAN or modems, but can also be used for any group of analog or digital signals having a bandpass up to 30 MHz or a data rate up to 20 Mbps.
-
Product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Cut Ends, 2m
A025DF4-C-0A200
Cable Assembly
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
8-Pin Power D-Type Cable, Female to Female, 1m
40-970-408-1m-FF
Cable Assembly
The 8-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Ultra-minute Photoelectric Sensor
EX-Z
-
Panasonic Industrial Devices Sales Company of America
At a thickness of 3mm, the EX-Z Series is one of the world's thinnest Photoelectric Sensors with a built-in amplifier which was achieved by utilizing a new Semiconductor packaging technology that does not use wire bonding. The compact design now makes it possible to install the sensors in narrow spaces that, in the past, could fit only a conventional fiber sensor head.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
Digital Multimeter
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
Intelligent Cable Fault Locator
TM800
-
TM800 Cable Fault Locator is a portable field instrument working on TDR and bridge methods, adopting advanced micro-electronics technology. It is designed to locate accurate fault points in such cables as telecommunication leadsheathed cable, plastic cable or user’s lead covered wire, while the faults include break, mix, earthing, defective insulation, or poor connecting. It is and ideal function-stable instrument for the field operator to improve work efficiency, in addition, it can also be used for circuitry project checking electric property testing of the cable.
-
Product
Opto-Isolator Board
MSXB 039
-
Opto-Isolator Board allows quick and secure connection of discrete wires at high DC and AC voltages to up to 8 separately-available optically isolated digital switching/sensing modules. Each channel may be configured for input or output.
