-
Product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
uSD Logger Shield
IFB-11001
-
This micro SD logger shield enables time-stamped logging of any signals measured by your Arduino project! Whether sensor shields, breakout boards or datalink connections, this shield will get your logger project up and running quickly. We've included an MCP79410 Real-Time-Clock module for flexible supply voltage timekeeping, which includes an on-board battery holder for a CR1220 battery (included, and is installed). In addition, the micro SD card is interfaced through a high-speed translator IC and supplied with a high-current LDO to meet the demands of the SD standard. Each pin of the Arduino has an offset pin attached for easy wiring to the massive 13x9 pin prototyping area, including the pins connected to the ICSP header! Whether you're using a Mega, Due or Uno, this board has your interfacing needs covered! Finally, the micro SD holder is a push to lock, push to unlock type, which makes it really easy to both install and uninstall your card.
-
Product
Quick Start Kit
-
Curtiss-Wright Defense Solutions
The OpenVPX CHAMP-WB/CHAMP-WB-DRFM/A25G/D25G 6U Quick Start Kit (QSK) from Curtiss-Wright Defense Solutions enables the system developer to rapidly prototype a core system for software and fieldprogrammable gate array (FPGA) development using the CHAMP-WB. Other components can be added to this basic configuration or alternative options can be explored.
-
Product
GHz Elastomer Sockets
-
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
Product
PXI-8513 , 2-Port, Software-Selectable PXI CAN Interface Module
780688-02
CAN Interface
2-Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
Software
HES Proto-AXI
-
The HES Proto-AXI™ software package, when combined with our HES™ prototyping boards, provides an efficient and robust environment for rapid design prototyping and/or algorithm accelerator development and bring-up.
-
Product
Machine Vision Systems
-
Machine vision solutions are typically used for automated inspection and process control across a wide range of industries. Due to the unique nature of machine vision solutions, they require a different form of thinking and problem-solving to implement accurate and repeatable results. From manufacturing quality inspection to cell and gene therapies, the Cyth team can help you determine the best technologies, architectures, and geometries to ensure your machine vision goals are met. Our machine vision lab enables us quickly prototype proofs of concept to demonstrate the feasibility of meeting your needs through a machine vision application.
-
Product
Custom & OEM Products
-
Applicos can provide custom hardware and software for many applications within the Analog/Mixed Signal area. We offer a unique combination of full-service assistance throughout the entire product realization process, from conceptualization to prototyping and manufacturing.
-
Product
SparkFun Sensor Kit
-
Do you have a good understanding of various sensors or need a variety of them for a project? The SparkFun Sensor Kit includes a sensor for just about every job. With everything included in this kit, you'll be able to sense gesture, humidity, temperature, motion, touch, sound, altitude, acceleration and more! These are some of our favorite sensors from each category. But wait, there's more! The SparkFun Sensor Kit now includes several of our sensor boards that feature the Qwiic Connect System for rapid prototyping!
-
Product
2-Slot 64-Bit 6U CompactPCI Backplane
cBP-6402R
Backplane
ADLINK offers a wide selection of standard backplanes from single up to 20 slots. Furthermore, a professional OEM team is capable of custom backplanes with a quick turnaround tailored to your specifications. We make designing, developing, prototyping, and maintaining your projects simple & efficient. For all your backplane needs, give us a call, we have a solution for you.
-
Product
SparkFun MicroView
USB Programmer
-
The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not only program the module, but use it to interface with your computer, Rapsberry Pi, or other USB device. The programmer has both male and female headers which allow it to be plugged into a MicroView module and a breadboard at the same time, making prototyping quick and easy.
-
Product
Decade Box, Capacitance, 5, 100pF to 11.111µF, 5 %
72-7265
-
Ideal for service, prototype and experimental use, this useful tool may be set at any non-polarized capacitor value from 100pF~11,111F, in 100pF increments.
-
Product
PXI Speciality
-
Power Interface, Prototype Cards and Programmable Resistor Cards for the PXI and GTXI platforms.
-
Product
USRP Software Defined Radio Reconfigurable Device
-
The USRP Software Defined Radio Reconfigurable Device is built on the LabVIEW reconfigurable I/O (RIO) and universal software radio peripheral (USRP) architectures. It includes a powerful FPGA for advanced DSP that you can program with the LabVIEW FPGA Module. The device includes 2x2 MIMO transceivers or four-channel superheterodyne receivers, supporting center frequencies from 10 MHz to 6 GHz, with up to 160 MHz of instantaneous bandwidth. The USRP Software Defined Radio Reconfigurable Device also optionally includes a GPS‐disciplined oven-controlled crystal oscillator (GPSDO), which provides greater frequency accuracy than temperature- compensated crystal oscillators. Prototyping applications include LTE and 802.11 prototyping, spectrum monitoring, signals intelligence, military communications, radar, direction finding, and wireless research.
-
Product
Supported Test Systems
-
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
Product
Cherry MX Switch Breakout
-
Cherry MX Keyswitches are top-of-the-line mechanical keyboard switches. They’re satisfyingly “clicky”, reliable up to tens-of-millions of key presses, and a standard in gaming and programming keyboards across the globe. With the SparkFun Cherry MX Switch Breakout we have made the switches more easily adaptable to breadboard or perfboard-based projects. The Cherry MX Switch Breakout is a perfect prototyping tool for projects ranging from a single-key user-input to fully-custom 101-key keyboards.
-
Product
Custom Solutions
-
We employ a collaborative process that provides our customers with the perfect component. This step-by-step process guides our customers through the creation of totally customized products. Our expert sales engineers take you from conceptual design to prototype, and then final part production, making the process as easy as possible.
-
Product
3D Printer Laboratory
-
Trialon’s commitment to providing 3D printing services is second to none. Our facility is equipped with state-of-the-art 3D printers that create accurate plastic prototype and end user parts.
-
Product
PXI Prototyping Module, 1-Slot, 96-Pin Micro-D
40-225A-101
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Hand Insertion Tools
-
Zierick Manufacturing Corporation
Ideal for low volume, short run and prototype PCB assembly applications, Zierick’s hand tools offer a simple and reliable method for inserting press fit and splay mounted terminals. The hand tool can be easily installed on any type of press machine for increased flexibility and faster insertion. With the addition of a lower tool die, terminals can then be splayed and locked into place to improve reliability and prevent part removal and rotation. Zierick hand tools are available for PCB-mounted quick-disconnect terminals, quick-disconnect receptacles, post receptacles, test points and IDC terminals. Simple and reliable method for inserting press-fit and splay mounted terminals. Single tool can handle multiple terminal insertion applications. Tools can be installed on almost any type of manual or pneumatic press. Please click here for a PDF user manual for Zierick's hand tools.
-
Product
Prototype Measurement Services
-
On-site measurement service for prototype parts using laser tracker for large volume parts or portable arm CMM with optional laser scanning for smaller parts. Point cloud generation and full part modelling is available. API measurement services is an ISO 17025 certified organization, accredited by A2LA, our 3rd party prototype inspection reports provide the necessary confidence demanded by your customers.
-
Product
RF Prototyping Kit
VXI-5501
-
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
Laser Type PM Sensor Evaluation Kit
-
Panasonic Industrial Devices Sales Company of America
The SN-GCJA5L Laser Type PM Sensor Evaluation Kit provides design in concept prototyping and testing of the Panasonic SN-GCJA5 Laser Type PM Sensor.
-
Product
System
SYS-36
-
Systems with 36" chambers tend to be a customer favorite for their flexibility. They are easily used for many different types of coatings. Often times they are best utilized in a prototype or multi part production facility where a specialized system such as a dual chamber box coater is not required. They are, however, still configurable for specialized processes.
-
Product
2-Slot 64-bit 6U CompactPCI Backplane
cBP-6402
Backplane
ADLINK offers a wide selection of standard backplanes from single up to 20 slots. Furthermore, a professional OEM team is capable of custom backplanes with a quick turnaround tailored to your specifications. We make designing, developing, prototyping, and maintaining your projects simple & efficient. For all your backplane needs, give us a call, we have a solution for you.
-
Product
SSOP-to-DIP Adaptor
Series 351000
-
SSOP IC to DIP Adapter. Allows the use of .65mm pitch surface mount ICs in thru-hole designs. Ideal for prototyping and testing/evaluating SSOP ICs. Adapter can be cut to smaller sizes by end user. Consult factory for panelized form or for mounting of consigned ICs.
-
Product
Multi-Domain Simulation
-
Every product engineering team deals with questions in the virtual prototyping phase, many of these covering multiple engineering domains. ESI's Visual-Environment multi-domain modelling allows these teams to work together in a single user environment, around a single core compute model. This multi-domain simulation environment has the capacity to integrate all virtual prototyping problems across CAE domains. In addition, its user-friendly interface and automation features empower engineering teams to be ever more productive!
-
Product
PXI FlexRay Interface Module
FlexRay Interface
PXI FlexRay Interface Modules provide two fully functional FlexRay interfaces, allowing an individual electronic control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. PXI FlexRay Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PCI Data Acquisition Boards
-
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
Product
Software Platforms
-
Discover complete solutions for Hardware-in-the-Loop (HIL) and Rapid Control Prototyping (RCP) testing. OPAL-RT offers the most advanced real-time simulation software platforms for power systems, power electronics, aerospace and automotive sectors: RT-LAB (Multi-domain, MATLAB/Simulink® based), HYPERSIM (Power Systems), and NI VeriStand (Automotive).
