Product

X-Ray Inspection System

MXI Ruby XL

-

Nordson Corporation

MXI Ruby XL - Nordson Corporation

Designed for the largest PCBs, Ruby XL allows 96 x 67 cm (37.9” x 26.4”) areas to be inspected non-destructively, with feature resolution up to 0.5 µm.

Product

Batch AOI Machine

Sherlock-300B

-

Manncorp

Sherlock-300B - Manncorp

Compact Sherlock 300B batch PCB inspection (AOI) system provides manufacturers with the benefits of inline AOI—hands-off board handling, automatic good/bad board sorting and minimal operator interaction—in the convenience and flexibility of a standalone AOI station that can be located anywhere in the facility and used to process boards from multiple production lines, including production lines that aren't inline/automated, such as smaller and benchtop lines. With an average cycle time of 10 seconds per board (including transport), Sherlock 300B automated optical inspection (AOI) machine can be used for everything from first article to 100% inspection for increased quality and production yields. (Cycle time measured using a 7.3" x 5.1" (185 x 130 mm) PCB with 253 parts.)

Product

Interfacing Components

-

Coda Systems Ltd.

Coda Systems Ltd.

Spring contacts and lands for PCB interconnection and a wide range of data, power and battery charging applications including: charging batteries in portable instruments power and data transfer pins in a docking station integral compliant contacts, such as for an antenna contact in a mobile phone board to board spring contacts for use in computerised gaming systems and telecommunications units

Product

Combination Board Tester

V250 / V250PXI

-

Qmax Test Technologies Pvt. Ltd.

V250 / V250PXI - Qmax Test Technologies Pvt. Ltd.

V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.

Product

Linear Testfixture (Cassette Not Included), UTT 586 x 413 mm

MG-04

-

MG Products

MG-04 - MG Products

FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 413 mm (wxd)• Outer dimensions: 800 x 635 x 100 x 190 mm (wxdxh1xh2)• Designed for changeable cassette

Product

3D Inline Solder Paste Inspection System

TROI 7700 SERIES

-

Pemtron Co., Ltd

TROI 7700 SERIES - Pemtron Co., Ltd

Using Moire' pattern, Pemtron's three-dimensional lead applicationdosage tester combines 2D color images with 3D measurement data toprovide more detailed, near-real PCB images, unlike traditionalcolor maps. We will also provide you with the best solution forhigh-quality and high-precision PCB production with a varietyof statistical programs, along with information you need toquickly and accurately judge positive/failure.

Product

Electronic Contract Manufacturing

-

ATX Networks Corp.

ATX Networks Corp.

Specializing in low-mid volume electronic manufacturing services, Pine Electronics, Inc. offers a wide range of printed circuit board assembly (PCB assembly), cable and box build assembly solutions. Our equipment, engineering and technical talent serves both multi-national and regional customers throughout the United States. Known for full-service PCB assembly work, Pine Electronics, Inc. is highly integrated and responsive. Each customer has a designated representative for all commercial and technical questions. This personalized service model enhances communication, expedites project development, and represents Pine’s commitment to customer service.

Product

Step & Repeat Non-Contact Inspection System for FPC and PCB

OHT-Ⅴ

-

OHT Inc.

OHT-Ⅴ - OHT Inc.

*Space-saving design and highly efficient and high-speed inspection, with top and bottom slider structure*Roller head enables to handle the reverse imposition.*Easy operation by new alignment mechanism*The machine handlingPCB is called "WSR"

Product

Board Repair Assistant & Quality Management System

QUAD

-

ASTER Technologies

QUAD - ASTER Technologies

QUAD (QUality ADvisor) is a flexible modular Quality Management system built around a centralized and open architecture database, providing traceability for any PCB electronic production data. QUAD covers all quality aspects of PCB assembly, sub-assembly and system build, allowing you to manage the quality data flow from product realization to product retirement.

Product

18 GHz Differential TDR/TDT Probe Kit

N1021B

-

Keysight Technologies

N1021B - Keysight Technologies

Connect PCBs and other devices without connectors to TDR/TDT modules in the oscilloscope mainframe

Product

Linear Testfixture (Cassette Not Included), UTT 105 x 170 mm

MG-01

-

MG Products

MG-01 - MG Products

FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (1000N) 650 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 105 x 170 mm (wxd)• Outer dimensions: 254 x 400 x 50 x 140 mm (wxdxh1xh2)• Designed for changeable cassette

Product

Manual Drive Unit

ATE MA260

-

INGUN Prüfmittelbau GmbH

ATE MA260 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 20 mm. Contact force max.: 300 N. Component on PCB: 58 mm

Product

Socket with Collet Contacts

Correct-A-Chip

-

Aries

Correct-A-Chip - Aries

Correct-A-Chip with Collet Contacts. Correct-A-Chip technology solves problems associated with the use of alternate ICs (due to availability, obsolescence, need for better performance, etc.) by eliminating the need for new PCBs.

Product

Module Spectrum

nRF52805 Series

-

Raytac Corp

nRF52805 Series - Raytac Corp

Raytac nRF52805 tiny and low cost modules spectrum covers MDBT42TV-192K & MDBT42TV-P192K series with both Chip Antenna and PCB Antenna option for selection

Product

LED Lighting Panel Tester

igentic® 821t

-

Sterner Automation Limited

igentic® 821t - Sterner Automation Limited

Growing demand for light emitting diode (LED) products combined with increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. Sterner Automation, a leader in LED test technology, provides solutions that address these specialized requirements, including the versatile igentic® 821t panel testing system. The igentic® 821t automated process combines advanced vision technology with flexible positioning and power-up capabilities to detect inconsistencies in individual LEDs at the panel production level. The resulting detection capabilities ensure that the highest standards are met while maintaining the capacity associated with today's high speed automated lines.

Product

160-Pin DIN41612 Connector, Straight PCB Mount, Female

C1604FX-4PS-0A

-

Pickering Interfaces Inc.

C1604FX-4PS-0A - Pickering Interfaces Inc.

Accessory allows a user to create their own PCB based termination solution. This female connector is modified to enable it to be fitted to Pickering's 40-967-160-F cable assembly

Product

Exchangeable Test Fixture

MA 2112/D/H/S-7

-

INGUN Prüfmittelbau GmbH

MA 2112/D/H/S-7 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg

Product

Automated Bare Board Tester with Built-In Camera

QTOUCH2404C

-

Qmax Test Technologies Pvt. Ltd.

QTOUCH2404C - Qmax Test Technologies Pvt. Ltd.

Qtouch2404C – Automated Bare Board Tester with in-built camera is designed to make automatic image capturing and probing of bare PCBs. It is designed to move on X,Y,Z directions making it possible to probe every test point. Flying Probe Tester is designed for testing high density fine pitched Single Sided / Double Sided and Multilayer PCBs for continuity and isolation using moving probes fixture –less technology.

Product

Mini SMP Connectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

Mini SMP connector series, also known as SMPM connectors, are ultra-miniature, high frequency connections commonly used in applications up to 65 GHz. Mini-SMP connector category will terminate to coax or PCB (printed circuit board) and many mini-SMP connectors are hermetically sealed. Pasternack mini SMP connectors are built to precise microwave and RF industry specifications and many are RoHS and REACH compliant. SMP mini connector products are built in male or female gender with 50 Ohm impedance. Mini-SMP connectors are available in straight or right angle versions, as well as, mountless options. These Mini-SMP connector designs include solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave components from Pasternack are in-stock. Not only in stock, but these SMP mini connectors will ship the same day as they are purchased.

Product

Impedance Measurement

CITS880s

-

Polar Instruments Inc

CITS880s - Polar Instruments Inc

Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.

Product

Strain Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.

Product

8 Pin Power D-Type Female Connector, 40A, PCB Mount

40-963-008-RF

-

Pickering Interfaces Inc.

40-963-008-RF - Pickering Interfaces Inc.

This connector is suitable for Pickering Interface's modules that use the 8-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.