Switches
enable on off function or change of direction.
See Also: Membrane Switch, Coaxial Switches, Crossbar, High Voltage Switching, Fiber Optic Switching, Microwave Switching, Optical Switch
-
product
PXI 4-Slot BRIC Matrix, 2A 1-Pole 232x6, 4 Sub-cards
40-596A-004
The 40-596A-004 is a PXI 1-pole 232x6 matrix in BRIC4 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
PXI MUX 2 Bank, 32 Channel Screened 1 Pole
40-610-021-S-2/32/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
PXI 4-Slot BRIC Matrix, 230x8, 1-Pole (5 sub-cards)
40-560B-021-230X8
The 40-560B-021-230x8 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
product
System Controls
Exar Corporation offers a broad range of USB VBUS power distribution switches supporting both the USB 2.0 and latest USB 3.0 specifications. These devices, the SP/XRP252x series, are offered in single and dual channels configuration for maximum design flexibility. The XRP2527 and XRP2528 are generic single and dual channels power distribution switches capable of operating at input voltage as low as 1.8V supporting the typical 1.8V, 2.5V, 3.3V and 5V power rails. Current limit for each channel is programmable from 300mA up to 1A through an external resistor and achieves better than 8% accuracy.
-
product
Low PIM Coaxial Switch, DC to 26.5 GHz, SP4T
87104R
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104R is a low PIM SP4T coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
PXI Microwave Relay, Dual SPDT, 26.5GHz, 50Ω, SMA, External Termination
40-781A-322
The 40-781A-322 (PXI) and 42-781A-3221 (PXIe) are dual SPDT 26.5GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
PXI 8 Slot BRIC 64x12 2A 1-Pole Matrix
40-597-102
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-0.25m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
LXI Microwave Multiplexer, SP4T, 6-Bank, 26.5GHz, 50Ω, SMA
60-803-306
Our 60-803-306 is a 6 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Dual 8:1 Optic MUX FC/APC Loop-Thru
60-850-022
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
PXI Switching Modules
PXI switching modules provide high-efficiency signal switching based on a standard PXI platform. Keysight offers a wide range of modules with a variety of characteristics: high-speed multiplexer modules with switch times up to 500 μs, general-purpose switching modules up to 300 W, and high-density matrix switcher modules that provide up to 256 two-wire intercept points.
-
product
160-Pin DIN41612 Connector, Right Angle PCB Mount, Male
40-963-160-RM
Accessory allows a user to create their own PCB based termination solution. Female versions are suited to direct connection to a Pickering Switching Module while male versions can be used to interface to a female cable assembly termination.
-
product
PXI Solid State Switch Module, 6xSPST, 30 A, Hardware Interlock
40-183B-011-HI
The 40-183B-011-HI has 6 high current SPST switches with hardware interlock in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
PXI 8 Slot BRIC 110x16 1-Pole (10 sub-cards)
40-562A-121-110X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
50 Ohm MMCX to MMCX Cable Assembly
40-977-571-2m
This 2m long MMCX cable assembly is part of the range of RF cables. Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Chassis - up to Twelve 8x1 or 4x2 Modules & up to Six 8k Modules
HXV/96-MF
These Chassis controls up to 12 8x1 modules, 12 4x2 modules, or up to 6 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
-
product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 1m, 250 Port
A500RMR-05F050D5C100
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber
40-850A-314-M62.5-HI
The 40/42-850A-314-M62.5-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Mixed function mezzanine side card for CPCI-S CPU boards
SCX-PCIE
The SCX-PCIE is a mezzanine side card for EKF CPU boards, equipped with a PCIe® Gen3 packet switch, onboard NVMe and SATA mass storage, and high-speed front I/O.
-
product
Custom Orthogonal 20 Slot 15U
Fully custom system design is based on the orthogonal topology. It allows for massive switching bandwidth between front computing slots and rear switching slots to be used in Telecom and Datacom industries.
-
product
NETernity™ Ethernet Switch
GBX411
The rugged GBX411 supports 24 Gigabit Ethernet and four 10Gigabit Ethernet ports with multiple configuration options that enable it to adapt to the most demanding customer connectivity requirements for network switching. Built to be Abaco Systems Rugged and qualified to a number of MIL standards, the GBX411 is capable of delivering robust reliability in the most challenging harsh environments.
-
product
PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual Transfer
M9156CH40
The Keysight M9156CH40 PXI hybrid dual transfer switch module provides an exceptional 0.03 dB insertion loss repeatability, high isolation, low SWR with a long operating life up to 10 million cycles.
-
product
LXI High Density 64x64 2A Matrix
60-552-007
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode
40-860A-332-HI
The 40/42-860A-332-HI is a PXI/PXIe triple insert/bypass switch with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI 64x4 Matrix Module, 2-Pole, 2A, 60W
40-583-001
The 40-583 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 64x4 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 160 pin DIN 41612 connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
product
PXI 8 Channel Switch Simulation Module
40-480-021
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 64-Channel, 1-Pole
42-614D-010
The 40-614D-010 (PXI) and 42-614D-010 (PXIe) 2-bank, 64-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Standard 4.10 (116.00) - 6.50 (184.00) Switch Probe
MSP-3C
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 140Full Travel (mm): 3.56Recommended Travel (mil): 85Recommended Travel (mm): 2.16Mechanical Life (no of cyles): 100,000Overall Length (mil): 2,140Overall Length (mm): 54.40Switch Point (mil): 30Switch Point (mm): 0.76
