Conductance
See Also: Battery Conductance Testers
-
product
700 W VITA 62 PSU Conduction Cooled-6 U-5 HP-AC
MS217765+RC
Designed to meet the requirements of VITA 62 for use in harsh environments. For use in AC systems, they are 6U high by 5HP (1-inch) wide modules with guide blocks, for use in conduction cooled VPX systems.
-
product
Pressure Mapping
TIRESCAN
Complete pressure imaging system for conducting tire tread analysis.
-
product
Spot Sensor
SP 1000-20R1
Advanced Thermal Solutions, Inc.
The SP 1000-20R1 is a single-sensor probe designed for measuring the surface temperature of solids. Its small size allows for the exact positioning of the sensor at the desired spot. The size of the sensor eliminates any conductive heat transfer that may occur through the lead wire, enhancing measurement accuracy.
-
product
Gem Testers
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
A diamond tester is a portable device used to check the authenticity of diamonds and test materials for their thermal and electrical conductivity. It can accurately indicate if the stone is a real diamond based on the gem's physical properties.
-
product
Rugged Embedded MIL-STD-1553Conduction Cooled XMC Card
AXE1553-x
Rugged embedded MIL-STD-1553 conduction cooled XMC card.
-
product
PXI 3A Power MUX BRIC, 18-Channel, 16-Pole
40-571-206
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Vision Data Acquisition and Management Software
Vision is the only software package available for ferroelectric testers that provides exceptional freedom to design, conduct, and review all procedures associated with any material experiment.The Vision test environment will collect all of the data acquired in a test sequence and organize it in archived data structures along with the test sequence definitions and data analysis tools, so that the experiment can always be recalled or reproduced.
-
product
Instrumentation Tutor
Unitech Scales And Measurements Pvt. Ltd
This comprises of temperature and speed using different methods. RTD, thermistor and thermocouple are used as sensors with digital temperature indicator to measure temperature. A small water kettle is supplied as a temperature source upto 100°C. Glass bead thermometer is used as standard temperature measurement source to conduct the experiment. Magnetic and photo reflective sensors are used to measure speed. A FHP motor with speed regulator is used as speed source. To the shaft 60 teeth tone wheels are fixed to generate pulses.
-
product
UAT Test Management
User Acceptance Testing is the final stage of the Software Development Life Cycle, which is conducted by the users. User Acceptance Testing is extremely important to determine whether the project is working fine as per the end user's point of view. The UAT test management process has to be done in an organized manner to reap maximum benefits from the process.
-
product
General Purpose Heat Flow Meters
Thermal conductivity defines a material’s ability to transfer heat. A precise and accurate measurement is critical for any process or material experiencing large or fast temperature gradients, or for which the tolerance for temperature changes is exacting. Accurate values are essential for modeling and managing heat, whether the component of interest is called on to insulate, conduct, or simply withstand temperature changes. Information about these properties are routinely used in heat transfer models of all complexities. Thermophysical property measurements also reflect important information about material composition, purity and structure, as well as secondary performance characteristics such as tolerance to thermal shock.
-
product
Spectrum Analysis For E5081A Up To 44 GHz
S960907B
The Keysight S960907B spectrum analyzer (SA) software application adds high-performance microwave spectrum analysis capabilities to the Keysight ENA-X up to 44 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Conduct simultaneous spectrum measurements using test and reference receivers. For efficient measurements of spurious signals emanating from mixers and frequency converters, combine the multi-channel SA with the internal swept-signal generators. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
product
Photometry
Photometric equipment is one of our main activities. Two distinct areas are involved - Industrial, Commercial, Road Lighting is one, while Automobile Lighting is another. Photometric equipment areused to conduct tests on Lamps, Industrial Lighting, Street Lighting,Automotive Lighting & related products. Most Photometric equipment are custom built to suit specific customer requirements.
-
product
CS/ONH-Analysis
G4 PHOENIX DH
The highly sensitive thermal conductivity detector allows analysis down to a sub-ppm range, while the optional mass spectrometer allows detection limits in the low ng/g range.
-
product
Non-aqueous Conductivity Probe
DT-700
From pure toluene to distilled water in one instrument.Quality control of non-polar liquids, ionic and surfactant composition.
-
product
3U VPX, 1/2 ATR, Conduction Cooled
ATRATS06BUNXHTC4
Elma’s line of rugged Air Transport Racks (ATRs) provide ideal cooling and reduced weight through superior design practices. DC and AC power options and custom I/O configurations are available.
-
product
Imaging Photometer & Colorimeter
LumiTop 4000 / 2700
Instrument Systems Optische Messtechnik GmbH
The patented optical design permits simultaneous measurement of all three sensors in one shot. The accurate spectral measurement is used as a live reference and transferred to the complete display area of the camera. This makes for extremely short measurement times and all relevant optical tests are conducted in a single test station.
-
product
Monitoring
Parker offers a broad range of onsite and laboratory solutions for monitoring, evaluating, and testing a wide variety of substances, from water and hydraulic oil to fuel and various gases, for conditions ranging from insolubility and viscosity levels through flow rate, conductivity, and pressure. They are suitable for use in industrial, marine, and numerous other applications.
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.

















