-
Product
Inductor Products
-
Macom Technology Solutions Holdings Inc.
They provide uniformity, durability and repeatability in circuit fabrication. The coils are polyimide coated to protect from ambient contaminants, and to eliminate the need for conformal coating. Quartz substrates are rugged and reduce dielectric losses. Chips may be bonded using either conductive or non conductive epoxies, and wire bonded with gold wire or ribbon by thermocompression bonding.
-
Product
Power Inductor - Impulse Winding Tester
19301A
-
Chroma Systems Solutions, Inc.
The Chroma 19300 Impulse Winding Tester with high/low inductance test technology has 1000V of impulse voltage and a 200MHz high speed sampling rate that satisfies most power inductor test requirements for a wide range of inductance products from 0.1uH to 100uH. The built-in Area Size Comparison, Differential Area Comparison, FLUTTER value, and LAPLACIAN value functions are able to effectively inspect coils for insulation abnormalities.
-
Product
Power Inductor
-
Is a passive two-terminal electrical component that stores energy in a magnetic field when electric current flows through it.
-
Product
Inductor Coils
-
SemiGen's Inductor Coils are manufactured using our thin film process on quartz substrates. The precision photolithography and non-chemical etching process provides clean edges to assure uniformity from coil to coil. By using quartz and applying a polyimide coating we produce a device that eliminates the need for conformal coating or staking. Inductors can be epoxied down with nonconductive epoxy and the wire bonded for connection.
-
Product
Inductor Tester
-
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
-
Product
Resistors and Inductors
-
Panasonic Automotive & Industrial Systems Europe GmbH
Our wide line-up of various Resistor and Inductor technologies supports the needs of the major industries such as Automotive, Industry, Telecom, HA and Medical markets. SMD, THT and axial shapes are available to support engineer's requirements.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
Test Fixture
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
AC Load Simulating Inductors
-
Osborne designs our AC Inductors to provide the desired inductance and to perform effectively with the dissipation characteristics presented to the circuit. Dissipation characteristics depend on circuit current and operating frequency. The Osborne design approach is unique to the extent that we design for frequency effects. The resulting inductors deliver superior performance.
-
Product
Bobbin Winding Coil Turn Tester
SS108 Series
-
This (SS108** series) winding coil turn testers are used for testing turn of various coils without core, like as: generator winding, transformer winding, relay, inductor, contactor, ignition coil, voice coil, etc.
-
Product
Antenna Tuning Unit
MS 2012
-
Antenna Tuning unit is used to automatically tune the notch antenna impedance. Microprocessor does tuning through tuning inbuilt algorithm. It has RS485 interface for external control unit interface. Capacitor unit (CU), Inductor unit, (IU) and RF Element are subunits of this antenna-tuning unit. System maximizes transmission.
-
Product
LCZ LCR Meter
SS1063
-
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor,cable,wire,etc.
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Bias Tee's
-
A bias "T" consists of a feed inductor to deliver DC to a connector on the device side and a blocking capacitor to keep DC from passing through to the receiver.
-
Product
Digital Power Modules
-
Renesas' digital PMBus power modules integrate a PWM controller, inductor, power MOSFETs, and passive components into one small package making the design of high efficiency, compact and intelligent power supplies easy.
-
-
Product
Alternate Constructions
-
In addition to Power Beads, Molded & Composite, Drum Cores and Round Wire Coil Inductors Pulse also designs and manufacturers multiple other constructions for catalog and custom solutions.
-
Product
ISL911xx Family Of Buck-Boost/Boost Regulators
-
The ISL911xx buck-boost regulator family is capable of working with the ultra-small inductors and capacitors to fit within less than 14mm2 board footprint, making them the ideal 2A switching converter solution for space-constrained mobile devices. The advanced wafer-level CSP package requires only a single inductor and very few external components, which minimizes overall space requirements. The ISL911xx regulators’ 2.5MHz switching frequency further reduces the power supply solution size.
-
Product
LCR Meter, 1 MHz to 300 M/500 M/1 G/3 GHz
E4982A
LCR Meter
The E4982A LCR Meter provides the best performance for the passive component manufacturing such as SMD inductors and EMI filters, where impedance testing at high frequencies (1 MHz to 300 M/500 M/1 G/3 GHz) is required. Not only for the manufacturing, the E4982A can also be utilized for R&D, quality assurance with the powerful functions such as list measurements.
-
Product
DC Filter Inductors
-
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
Product
32 Channel Pass Through Card
SET-2090
-
The input signals can be configured by customers. Each input channel can be tested, conditioned or measured in different ways. Various inductors, filters, pull-up or pull-down resistors can be used for this purpose. In standard configuration, the input signals are transmitted directly to the output.
-
Product
Harmonic Trap Inductors
-
Osborne designs harmonic trap inductors to work in conjunction with capacitors in power systems to prevent specific line-frequency harmonics from flowing back to the power source (point of common connection). This power quality design approach prevents harmonic currents from flowing to the main facility power system and/or to the utility power system. The Osborne system also reduces unnecessary power losses and power-system pollution.
-
Product
Drum Core Inductors
-
Drum core inductors are so named as the conductor (round magnet wire) is wound directly onto the ferrite core which is shaped like a drum or spool. The wire is then connected to the core, a plastic base or metal lead frame to form the surface mount termination. Drum core inductors come in unshielded (high saturation current but potentially more EMI) and shielded constructions (lower saturation current but closed magnetic path for lower EMI). The shielded constructions use either a second ferrite core or a magnetic resin epoxy to create the magnetic shield.
-
Product
LCR Meter, Hand Held, 100 kHz, 2 kH, 20000 µF, 0.2 Gohm
72-10465
-
The 72-10465 from Tenma is a LCR meter in orange and grey colour. It features an easy to read dual LCD (40mm x 63mm) display measurement of 19999/1999 (main/auxiliary). It also has series and parallel measurement modes which can be used to select quality factor, loss factor, phase location angle and equivalent resistance of measure articles. Intelligent detection and five different test frequencies enable accurate readings for all sizes of capacitors and inductors. The user can also access the stored data on a PC with the included USB connection and interface software. The compact size and case make this unit far more portable than a benchtop meter.
-
Product
µModule Isolated Transceivers
-
Analog Devices µModule (micromodule) isolated transceivers provide robust galvanic isolation for digital serial communication interfaces, including SPI, I2C, RS-485/RS-422, RS-232, and USB. Isolation barriers are implemented using Ethernet transformers, coupling capacitors, or embedded inductors. All devices are simple to configure, have very low EMI susceptibility and emissions, and feature high noise immunity to preserve signal integrity.
-
Product
Toroid Core Coil Turns Testers
SS107A
-
The magnetic torrid ring core winding coil turns tester (SS107A) adopts the high speed center microprocessing unit circuits and precise measurement A/D circuits. This coil turns tester is used to count the coil turns of various torrid core winding coils. Like as: torrid core inductors, torrid core transformers, torrid core sensors, wate meter sensors, torrid current transformers, torrid core choke coils, etc. The tone tester is named magnetic ring core coil turn tester also.
-
Product
Active Antennas
-
Is an antenna that contains active electronic components such as transistors, as opposed to most antennas which only consist of passive components such as metal rods, capacitors and inductors.
-
Product
Network Probe for TC-NT2
TC-TP1
-
TRENDnet´s TC-TP1 is an easy-to-use amplified inductor and tone probe that is used for tone tracing and line testing. The TC-TP1 features a simple push button that provides easy operation and conserves battery power. This ergonomically designed device comes with adjustable volume control and signal LED for enhanced accuracy in noisy environments.
-
Product
Dayton Audio Test System
DATS V2
-
Highly accurate measurement of loudspeaker impedance and T/S parametersEasy-to-use, fully-featured measurement software with intuitive interfaceCompact USB measurement module with molded test leads and alligator clipsSoftware includes signal generator, scope, and measurement of inductors and capacitorsData can be saved to create a driver parameter library or exported to popular box design programsNew V2 hardware and software simplify setup and eliminate warm-up/cool-down times
-
Product
Round Wire Coil Inductors
-
Round wire coil (RWC) inductors come in six platform sizes and enable the highest efficiency of any SMT inductor through the use of a low loss ferrite core material which minimizes AC losses and also eliminates thermal ageing. The use of round magnetic wire instead of rectangular flat coils enables a lower cost while still maintaining a low DCR and small footprint. The platforms have passed the AEC-Q200 stress test qualification proving the designs robustness and suitability to difficult environments but the parts are not IATF certified. The platform range from 7.6×7.4×6.4mm to 26x26x15mm and are suitable for a wide range of applications and markets including communications, computing and industrial.
-
Product
Switching Power Supplies
-
PeakTech Prüf- und Messtechnik GmbH
A type of power supply that works by switching current into a high-frequency transformer or inductor at frequencies much higher than the input or line frequency
