Pickup
-
product
SECONDARY IGNITION PICKUP
MD75300
*Safely acquire high voltage waveforms with this high impedance, active pickup*Works with spark plug wires and coil on plug ignitions with MDAUTOWAVE, AUTOWAVECAMO and MDAUTOWAVE2*Adjustable sensitivity increases waveform acquisition accuracy
-
product
Optical Pickup
1037-DTS
TESCO introduces a new optical pickup (Catalog No. 1037-DTS) for one way meter communication through the calibration LED found on most solid state meters. The pickup senses infrared pulses from ANSI compliant meters for complete, automatic testing.
-
product
Probe & Pickup
1035
TESCO’s Catalog No. 1035 Probe & Pickup combines the best of communication between a PC and a meter. No longer do you have to disconnect the pickup to reconnect to a PC with this all-in-one device. Save time with less hassle.
-
product
Piezoelectric Vibration Pickup
PU-8ALSF
*Side outlet type with assembled *cap nut*Built-in amplifier*Use up to 150 ℃ enabled
-
product
Piezoelectric Vibration Pickup
PU-611E
Waterproof general purpose. Side outlet type. Water resistant(IPX7).
-
product
Optical Pickup for Itron Gen™5 Riva™ Meter
1037-RIV
Tesco’s Cat. 1037-RIV is designed to hold the pickup sensor directly above the output location on these new meters. It conforms to the shape of the new meter and secures easily to provide hands free operation.
-
product
Piezoelectric Vibration Pickup
PU-626E
*Connector type with upper outlet*Waterproof (IPX6), suitable for a wide range
-
product
Piezoelectric Vibration Pickup
PU-7ALT6
*Upper outlet type*Use in water up to 15 meters*depth enabled
-
product
Piezoelectric Vibration Pickup
PU-8ALT6
*Upper outlet*Built-in amplifier*Use up to 150 ℃ enabled
-
product
Piezoelectric Vibration Pickup
PU-7SLT6
*Upper outlet type*Use in water up to 50 meters*depth enabled
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
Acceleration Pickup Calibrator
VX-1100A
VX-1100 is for a piezoelectric type accelerometer which is widely used for measuring vibration. This compact calibrator is effective for checking operation(sensitivity) sensors before measurement to acquire accurate data.Built-in sensor amplifier and display in one unit allows direct reading of the sensitivity. This calibrator excites the sensor at a frequency of 159 Hz and acceleration of 10 m/s2 rms, and the sensor outputs can be used as calibration signals for a vibration measuring system.
-
product
C Series Frequency Input Module
The C Series Frequency Input Module is designed to acquire isolated frequency inputs from magnetic pickup sensors, variable reluctance sensors, Hall effect sensors, and other transducers with a frequency output. Additionally, the C Series Frequency Input Module provides isolation, configurable thresholds, selectable filtering, and embedded counter measurement logic. These measurements can be synchronized with other frequency, analog, digital, and counter measurements in a single acquisition.
-
product
True RMS RF Millivoltmeter
3440A
The 3440A measures the true rms of low level RF and microwave signals to over 1GHz. High rms accuracy, traceable to NIST, is assured regardless of waveshape. Common calibration errors are eliminated through temperature compensation of the probe detector diodes; double shielding protects the interchangeable probes from rough handling and pickup. Relative gain or loss measurements are simplified by a 0 dB reference adjustment. DC output proportional to the ac input is provided for analog recorders and to allow operation as an ac-dc converter.
-
product
Vacuum Pen
Stand-alone vacuum pick-up system used for pick and place functions. Requires shop air or can be air powered through TS350 Series or TS500R dispensers/controllers. Features an adjustable vacuum control knob to set desired vacuum. Maximum operating pressure 100psi (6.9bar).
-
product
AC-Powered, AC Voltage Monitor, Adjustable
VMA
NAI’s VMA is a field-adjustable, AC-Powered, AC Voltage Monitor used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits.High and low voltage limits, and "pick-up" and "drop-out" time delay are field-adjustable. The VMA voltage monitor is ideally suited for rugged defense and industrial applications.
-
product
Display-Only Dynamometer Testing Instrument
DynTek-PC
The DynTek-PC for engine dynamometers is a display-only system intended for basic engine dynamometer testing requirements. This system provides for the measurement of torque in either tension or compression (both clockwise and counter-clockwise engine rotation) and speed from a standard Magnetic Pickup. The system is designed to set on a table or desktop near the PC.
-
product
Digital Engine Analyzer/Multimeter
385A
The #385A has many of the necessary features required for today’s automotive diagnostics. Use frequency readings to test crankshaft and camshaft sensors, for example. The #385A comes equipped with an RPM pick-up, probe test leads, alligator clip test leads, protective holster, instructions and installed 9V battery. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
product
Measuring Wheel
B20-S
Simple and light Measuring Wheel B20-s can measure up to 10,000m at 10cm graduation.The counter is indicated in 5 digits and has reset button. When we use Leak Noise Correlator LC-2500, we need to input the between pick-up sensors.
-
product
Piezoelectric Vibration Pickup
PU-6ALSF
*Side outlet type*Easy to remove due to cap nut type*Use up to 80 ℃ enabled
-
product
Non - Contact Voltage Detector
Model 273 HP
Kusam Electrical Industries Limited
The 273 HP is a Non-contact voltage detector. It has two ranges for selection.The 273 HP consists of an internal pickup sensor, a function selection switch, a visual and a sound annunciator. With the 273 HP, physical contact with electrical conductors is not necessary when testing for live lines. Its sensor senses the radiated field which surrounds live conductors. Radiated field strength increases with voltage and decreases quickly with distance or earth shielding
-
product
Speed Sensors
Speed sensors for both indoor and outdoor environments with options featuring kits for motors, geartooth pickup, tachometers, and stroboscopes.
-
product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
product
Signal Conditioner
SA420
Features • Works with a remote / external pulse frequency output sensor (NPN, PNP, or Mag Pick-up) • Accepts wide range of input frequencies 0.01 Hz to 10 kHz • 4-20 mA and 0-10 VDC outputs proportional to shaft speed • Field adjustable calibration • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • DIN rail mount
-
product
EZ TACHOMETER PLUS
ETP328
*Small engine tachometer reads engine speeds up to 20,000 RPM*Works wirelessly or with inductive pick-up clip*Accuracy: +/- 10 RPM
-
product
4-20mA Converters
4026
SPECTEC Innovative Sensor Solutions
Model 4026 Freq to Voltage or Freq to Current Converter accepts frequency input from any magnetic speed sensor, digital magnetic pickup or Hall effect zero speed sensors. Input and output configurations are field selectable. Input range is adjustable between 1100 Hz - 10 kHz or 75Hz to 1100 Hz. Output selection can be configured as 4-20mA converter, 10-50mA converter, 0-5 V FTV converter or 0-10 V FTV converter. ZERO and SPAN adjustments easily calibrate to almost any measurement range, with little interaction between the adjustments.
-
product
Speed
Speed sensors for both indoor and outdoor environments with optinos featuring kits for motos, geartooth pickup, tachometers, and stroboscopes.
-
product
Remote Receiver
10780F
The Keysight 10780F Remote Receiver with fiber-optic pickup provides maximum layout flexibility for Keysight laser interferometer positioning systems. Remote pickup capabilities allow mounting of the heat-dissipating receiver electronics away from measurement areas, resulting in high measurement stability, accuracy, and repeatability.





























