Parallel Digital Interfaces
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Digital / Synchro Converter
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
Digital Synchro and Digital to Resolver
DSL- DRL
Digital / Synchro Converter
Computer Conversions Corporation
The DSL - DRL Series are highly reliable, miniature, low profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
Product
8-Ch Relay And 8-Ch Isolated Digital Input PCIE Card
PCIE-1760
Digital Input PCIe Card
8 opto-isolated digital input channels with counter/timer function8 relay actuator output channels2 opto-isolated PWM outputsProgrammable digital filter function for DIJumper selectable dry contact/wet contact input signalsUp event counters for DILED indicators to show activated relaysPattern match interrupt function for DIChange of state interrupt function for DIBoardID switch
-
Product
GPIB Connection Module
DSOX2000-806
Interface Module
DSOX2000-806 GPIB Connection Module plugs into the rear panel expansion slot to provide handshaking and interface communications over an 8-bit data bus.
-
Product
8-Ch Isolated Digital Input Module
ADAM-5052
Digital Input Module
Digital input level: Logic level 0: +1 V max.Isolation voltage: 5000 VRMSPower consumption: 0.27 W (max)Channels: 8
-
Product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
Digital Multimeter
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
MIL-STD-1553 & ARINC XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-MA4
Interface Module
The XMC-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
Product
PXIe-6593, FlexRIO High-speed Serial Module (16 Gbps), KU060
785977-01
Serial Interface
PXIe, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument - The PXIe‑6593 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe‑6593 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2233-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Multi-Channel, Multi-Protocol 1553, ARINC, WMUX Interface for 3U PXIe
Interface Module
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
Product
PCIe-6537B, 32-Channel, 50 MHz, 200 MB/s Digital I/O Device
782631-01
Digital I/O
32-Channel, 50 MHz, 200 MB/s Digital I/O Device - The PCIe-6537 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
NI-9402, LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module
779987-01
Digital Module
LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module - The NI‑9402 is a per‑channel configurable digital I/O interface for input or output. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9402 for … implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 1 Channel, 500 MHz Bandwidth
M4I.2210-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787454-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
RJ45 (Ethernet 100 Base T) to 90 Series Interface
J90RJ45I
Ethernet Interface
RJ45 Ethernet connector for VPC Tripaddle ITA moduleUp to 3 connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
Product
REM-11175, 16-Channel (Output), 24 V, 2-, 3-Wire Digital Module for Remote I/O
784745-01
Digital Module
The REM-11175 is a digital output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and … individual modules mounted on a DIN rail. You control the REM-11175 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM-11175 features 2- and 3-wire spring terminal connection methods and circuit and overload protection.
-
Product
Network Interface Card
PMC-GBIT-DT2BP
Interface Card
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
Product
I²C/SPI Interface Device
Interface
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Product
PXIe-5763 , 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785160-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 12 Channels, 12 Single-Ended Inputs
DN6.448-12
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Digitizer with two 125 MS/s, 14-Bit Channels, Recommended for VXI Systems
6084-2105
Digitizer
The Astronics 6084-2105 digitizer includes two 125MS/s, 14-bit digitizer channels and is recommended for VXI systems that need either improved accuracy or replacement of an obsolete instrument. Wide dynamic sampling, a powerful acquisition engine, and excellent AC/DC performance ensure an upgrade for your VXI system that will preserve your legacy investment for years to come.Key features include:Dual 14-bit digitizers for SE or DIFF operation at sample rates up to 125 MS/sDC accuracy of 0.15% ± 800 µV on low voltage rangesSFDR 80 dB at 1 MHz Wide input ranges from 0.25 Vpk to 256 VpkPerformance upgrade or replacement for existing VXI applications Pre- and post-triggering availableWaveform storage of 32 M samples per channel
-
Product
PXIe-7912, KU040 FPGA, 4 GB DRAM, x8 Gen 3 PXI Coprocessor Module
785173-01
Digital I/O
The PXIe-7912 provides a Xilinx Kintex UltraScale FPGA that you can program with LabVIEW or Xilinx Vivado to add signal-processing capabilities to PXI Express systems. Using the x8 Gen 3 PCI Express architecture and peer-to-peer streaming, PXI FlexRIO Coprocessor Modules can stream data to and from other modules in a PXI chassis at up to 7 GB/s without a host controller. You can pair these modules with another PXI instrument, such as a PXI Vector Signal Transceiver, to add functionality, such as running complex algorithms in real-time. The PXIe-7912 KU040 FPGA is ideal for applications that require a moderate amount of signal processing.
-
Product
PCIe-4065, PCI Express, 6½-Digit, ±300 V Digital Multimeter Device
779771-01
Digital Multimeter
The PCIe‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
PXI/PXIe High Resolution Waveform Digitizer Family
PXD(e)721x
Waveform Digitizer
The PXD(e)721x High Resolution Digitizer- Family features up to two 100MS/s simultaneously sampled input channels with 16 Bit resolution, input voltages up to ±60V and a bandwidth of 50MHz (100MHz with option DBW).Every digitizer channel has its own 2MB memory which allows up to 1 million samples. Depending on the amount of channels and the isolated option, the digitizers are built into a compact 3U PXI device for 1 or 2 slots. All isolated devices have a high common mode rejection ratio (CMRR). A great number of trigger capabilities results in multiple instrument and channel synchronization possibilities.Data can be acquired before and after the trigger event with a programmable sample counter, that controls the number of data points.
-
Product
64 Output USB Modular Digital I/O
U2653A
Digital I/O Module
The Keysight U2653A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
sbRIO-9375, Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781212-01
Digital Module
Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The sbRIO‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The sbRIO‑9375 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
Digital I/O Module
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
Handheld Digital Multimeter, 4 Digit
U1242B
Digital Multimeter
10K counts digital multimeter with switch/relay counter, harmonic ratio and dual/differential temperature functions for installation and maintenance troubleshooting.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.596-04
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.825-04
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
