Clock Recovery
-
Product
Clock And Trigger Synchronization System
CLKSYNC-50
-
CLKSYNC-50 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
High Impedance Differential Clock Divider
-
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
-
Product
Real-Time Clock & Interrupt Module
RCIM IV
-
The Real-Time Clock & Interrupt Module (RCIM IV) is a multifunction card designed for time-critical applications on Concurrent Real-Time’s iHawk™ multiprocessing systems. The RCIM provides key functionality for single system as well as multiple system applications.
-
Product
GPS Wireless Clock
-
Signals & Systems India Private Limited
GPS Clock offers an easy, cost-effective solution for accurate, synchronized time displays without expensive, disruptive installation procedures. Because there are no wiring requirements, installation times are drastically reduced. It is ideal for renovation projects, as there is no need to worry about installation work, as well as new construction. The GPS clock can be synchronized through GPS Antenna or Wireless Antenna. The display can be wall/panel / tabletop mountable. It can be used as a wireless clock to synchronize many wireless slave clocks in and around the buildings.
-
Product
Four Channel Clock Driver Card
PI-41401
-
The PI-41401 is a four channel Clock Driver card capable of operating up to 140 MHz at 3V and 100 MHz at 5V amplitudes into a 50 Ohm load. The PI-41401 has a clock rate of 90 MHz at an amplitude of 5 volts into a 1-MOhm load. Into a high impedance load the output voltage range is from –5 volts to +8 volts with the pulse amplitude ranging from 0V to 9V. When driving a 50 load the voltage range is –2.5 volts to 4.0 volts with the pulse amplitude ranging from effectively 0V to 4.5V. Each channel has a common edgespeed control to vary the rising and falling edges of the output waveform. The adjustable slew rate range, for any amplitude, is the minimum edgespeed of that amplitude times 5. The output pulse amplitude and the load being driven determine the range of variability.
-
Product
Virtual Clock for Application Testing
Time Machine
-
Time Machine provides software virtual clocks that enable you to time travel your applications into the future or the past, facilitating time shift testing on your date and time sensitive application logic, such as month end, quarter end, year end processing, billing cycle, work flow, regulatory go live, and policy life cycle.
-
Product
IPhone Data Recovery Tool
iPhone Jig (several chips)
-
iPhone and iPad is special with its system.encrypted with several chips;once they get damaged(can't boot or start),it is hardly to get data back.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-40
-
CLKSYNC-40 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
GPS Master Clock
-
Signals & Systems India Private Limited
GPS Master Clock System – MCS-GPSMC-1010 is a 3U Card rack type, 19” Rack-mountable Redundant GPS Time Server which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from any one of the sources like GPS or GLONASS or Time protocols such as NTP and IRIG. It distributing the same time signal through several types of interfaces. It provides redundancy for Power and GPS receiver to increase reliability and offers protection against time synchronization failure. The system is field-upgradeable and an extremely flexible system, designed to handle time synchronization requirements today and in the future. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, DCF77, BCD parallel data, Ethernet Fiber Optic & RS485/RS232 outputs. System enables configuration and monitoring through Web-based application. It supports a wide range of power supply either 90V-260V AC/DC or 18-36VDC or 36V-72VDC. Power supply model can be mixed and matched as required by the user, depending upon power supply options available at the installation site.
-
Product
Reference Clock T Connector
780540-01
-
The SMA-SMA-SMA T Connector, sometimes referred to as the Reference Clock T Connector, connects RF wireless test devices and PXI modular instruments to other accessories. It is a 50 ohm … impedance connector that measures 0 GHz to 10 GHz.
-
Product
Dual Channel Clock Driver Card
PI-41400
-
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
-
Product
MAGNA Series "Large Digit" Clocks
Models CLK4 & CLK6
-
4-digit model (CLK4) with HH:MM display, or 6-digit model (CLK6) with HH:MM:SS display. Large-digit displays with a digit height of 2.2" (57 mm), 4.0" (102 mm), 5.7" (144 mm), 7.9" (200 mm), or 11.0" (280 mm) for long viewing distances. Optional relays and data I/O. Choice of display brightness and cases for indoor or outdoor mounting.
-
Product
Multi-Channel Clock Generator
XCLK1
-
Curtiss-Wright Defense Solutions
High-speed analog IO acquisition systems need a high quality master reference sample clock.Accurate synchronization in the 100MHz and up frequency domains is not easy and it’s a critical performance limiting factor if not done well. The XCLK1 multi-channel clock generator solves these problems.
-
Product
Crease Recovery Tester
TF110
-
TESTEX Testing Equipment Systems Ltd.
Crease Recovery Tester, to determining recovery properties of fabrics by creasing in a loading device for a predetermined time using a weight suitable for the test method specified (BS/ISO/AATCC), After transferring the specimen to the clamp of the tester, the specimen is allowed to recover and the angle of recovery recorded. Fabric Crease Tester complies with ISO 2313, AATCC 66, BS EN 22313， etc.
-
Product
Digital Hygro-thermometer With Clock Alarm Function
KM 918A
-
Kusam Electrical Industries Limited
• Temperature range : -10 ~ 60°C / (14 ~ 140°F)• Temperature accuracy : ± 1°C / (± 1.8°F)• Temperature resolution : 0.1°C / °F• Humidity range : 20% RH ~ 95 % RH• Humidity resolution : 1 % RH• Humidity Accuracy : 8% RH• Clock, temperature and humidity display• Room temperature• Room Humidity display• Maximum or minimum memorization function• Alarm clock function at a desired hour• Power : Single 1.5V DC AAA battery
-
Product
Multifrequency Clock Synthesizer - 6U VPX
Model 5790
-
- Simultaneous synthesis of up to five different clocksEight SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
Product
Word Clock Distributor/Generator
DCD-24
-
The DCD-24 is both a Word Clock Generator and a Distributor, using exceptional jitter reduction technology. With 24 BNC outputs the DCD-24 sends accurate Word Clock throughout an installation.
-
Product
Clock And Timing
-
Achieving highly accurate precision timing is no easy feat from a technology perspective, so it’s important to find a resource you can trust to reduce design risk and speed your time to market. Our end-to-end timing solutions generate, distribute and apply precise time for multiple industries, including communications, aerospace and defense, IT infrastructure, financial services, power utilities and more. We provide a broad range of clock and timing solutions ranging from MEMS oscillators to active hydrogen masers. Explore our portfolio of clock and timing components and systems to find the right solution for your project.
-
Product
Multifrequency Clock Synthesizer - 6U VPX
Model 5890
-
- Simultaneous synthesis of up to 10 different clocks- 16 SMC clock outputs- Typical phase noise: 105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Eight quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
Product
Clock Dividers
-
The Analog Devices clock divider portfolio features ultralow noise and low power consumption options to help meet your design needs.
-
Product
UFS Data Recovery Tool
-
UFS is full encrypted on mobile phone;UFS BGA153 is widely used on Samsung mobile phone.
-
Product
Optical Lattice Clock
-
Our strontium lattice clock project aims to create the world’s first commercially available fully integrated optical frequency atomic clock. The clock will be compact, transportable, easy to use and based on optical lattice technology enabled by the SolsTiS. The strontium lattice clock will achieve frequency uncertainties below 10-17, a level unprecedented on the global market.
-
Product
PCI, PCI Express and USB radio clocks
-
Meinberg Funkuhren GmbH & Co. KG
Although the PCI Express is PCI-compliant, PCIe cards are based on a different concept. Less lines are used to transfer the data, for example in the case of PCI plug-in cards.
-
Product
Synthesized Clock Generator
CG635
-
Stanford Research Systems, Inc.
The CG635 generates extremely stable square wave clocks between 1 µHz and 2.05 GHz. The instrument''s high frequency resolution, low jitter, fast transition times, and flexible output levels make it ideal for use in the development and testing of virtually any digital component, system or network. Clocks from 1 µHz to 2.05 GHz. Random jitter <1 ps rms. 16 digits of frequency resolution. 80 ps rise and fall times. CMOS, PECL, ECL, LVDS & RS-485. Phase control and time modulation. PRBS for eye-pattern testing. OCXO and rubidium timebase.
-
Product
Clock Drivers
-
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a pattern generator and allow the user to adjust the output parameters to suit their device and testing requirements. Clocks can be "tweaked" in real-time to determine optimal operating parameters for a particular device, or else programmed in accordance with a test plan for automated production test.
-
Product
Adaptive Clocking (TCK) Adapter
-
Blackhawk has extensive experience in emulation design and can help you with any emulation requirement. We can taylor a solution based on cost, form factor, host interface and performance to meet your needs.
-
Product
AATCC Wrinkle Recovery Tester
M272
-
To determine a fabric's ability to recover after wrinkling under a predetermined load for a set period of time. Set of 3-D plastic replicas are available to grade fabrics.
-
Product
Clock Distribution Devices
-
Analog Devices offers ultralow jitter clock distribution products that fan out given signals for wireless infrastructure, instrumentation, broadband, ATE, and other applications demanding subpicosecond performance. Our clock products are ideal for clocking high performance analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). ADI clock ICs integrate PLL cores, dividers, phase offset, skew adjust, and clock drivers in small chip scale packages.
-
Product
Programmable Multifrequency Clock Synthesizer - 6U VPX
Model 5891
-
- Simultaneous synthesis of up to 10 different clocks- 16 SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Eight programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
Product
Wrinkle Recovery Tester
TF112 AATCC
-
TESTEX Testing Equipment Systems Ltd.
AATCC Wrinkle Recovery Tester is used for determining a fabric's ability to recoverafter wrinkling under a pre-determined load for a set period of time.Provided with a set of 5x3 dimensional plastic replicas to grade fabrics 1-5.
