Developers
See Also: Development, Software Development, Development Boards, Test Development
-
product
Automated Telemetry Test Station
ATTS5000
Systems Engineering & Management Company
The ATTS 5000 was developed by SEMCO to ensure that receiver systems successfully perform at both IRIG 118 Chapter 4 recommended tests, as well as additional customer-specified performance parameters. The ATTS 5000 ensures that the highest quality test data is consistently and repetitively collected on each and every system.
-
product
Standard Voltage 9 Pin D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
Test Program Sets
Each grouping may consist of 15 levels of development ranging from Complexity 0 to Complexity 14, with level 14 the most complex. Within each complexity, nine additional subcomplexity levels exist.
-
product
RF Chamber
HDRF-CHM-SERIES
*RF Chamber Designed and Developed for WLAN , Wireless device testing.*Ideal RF Enclosure for 802.11a, b, g, n, ac Device Testing*Ideal RF Shield for Bluetooth, RFID, 3G Device testing
-
product
EMI Test Receiver
ESRP
The R&S®ESRP EMI test receiver has been designed for diagnostic measurements during development and for precompliance measurements to prepare products for final certification testing. It measures electromagnetic disturbances in the 10 Hz to 7 GHz frequency range, using either conventional stepped frequency scans or FFT based time domain scans to significantly speed up measurements.
-
product
Power Profiler, DC Energy Analyzer, Power Supply, Digital Multimeter, Source Measure Unit, Power Debugger
Otii Ace Pro
Otii Ace Pro is the big brother to Otii Arc, and is an instrument that can precisely source voltage (up to 25 V) and current (up to 5A) and simultaneously measures voltage and/or current with a high sample rate (50ksps) and low step size. It computes power and energy and enables engineers and developers to easily see and optimize the energy consumption and battery life of their devices under test.
-
product
cPCI and PMC Compatible Adapter Carrier
cPCIBPMC3U64ET
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
product
Code Execution Time Analyzer
TimingProfiler
AbsInt Angewandte Informatik GmbH
Constantly monitor timing behavior during software development, even at the earliest stages. Identify bottlenecks when you haven't even settled for a particular processor derivate yet, and measurements on physical hardware are plain impossible. This makes TimingProfiler ideally suited for constantly monitoring timing behavior during software development and in model-based development environments
-
product
Embedded Real-Time Robotic Controller with 11th Gen Intel® Core Processor
ROScube Pico TGL
ADLINK’s ROScube Pico TGL is a real-time ROS 2 enabled robotic controller based on the 11th Gen Intel® Core™ i7/i5/i3 processors with Intel® Iris® Xe Graphics featuring exceptional I/O connectivity and supporting a wide variety of sensors and actuators for unlimited robotic applications. The ROScube Pico TGL supports the full complement of resources developed with ADLINK Neuron SDK. Bundled with AI features and capabilities and developed with the Intel® distribution of OpenVINO™ toolkit, the ROScube Pico TGL is a perfect platform for industrial service robot applications such as autonomous mobile robots (AMR) and autonomous mobile industrial robots (AMIR).
-
product
IO-Link Transceivers
IO-Link is a Factory Automation fieldbus-independent communication standard dedicated to connecting sensors and actuators as described in the IEC 61131-9 standard. Easily integrated with any of the most commonly used communication protocols found in factory automation systems through dedicated interfaces or bridges, it is a simple solution for extending existing networks to connect remote sensors and actuators. Developers will take full advantage of the Industry 4.0 or Industrial Internet of Things (IIoT) concept where every sensor and associated data point is used to control and optimize even the most complex industrial processes in real time.
-
product
Mining and Geotechnical
ESG Solutions is your best choice for subsurface diagnostic solutions for mining and geotechnical applications. Since 1993, our microseismic monitoring specialists have provided mining services in over 40 countries, with 100 projects each year on average. We work with you to understand your unique challenges and monitoring goals, then develop the right all-in-one solution for your operation.
-
product
Magnet Testing
3MTS – Triple Axis Handheld Teslameter
3MTS is a handy 3-axis teslameter, which was developed in cooperation between Matesy GmbH and SENIS AG.
-
product
Vector Signal Generator
R&S®SMW200A
Performance and functionality requirements vary depending on test setup and application. The R&S®SMW200A is unrivaled in mastering this challenge and sets new standards for signal generators. When developing and verifying any type of DUT, including component, module and complete base stations – the R&S®SMW200A always easily generates the appropriate test signals with top performance. The flexible modular design of the R&S®SMW200A can be equipped with the exact options required for specific applications. Any configuration is possible, from a classic single-path vector signal generator to a multichannel MIMO receiver tester.
-
product
Primary Current Injection Test Trolley
SCR ELEKTRONIKS have developed primary and secondary Current injection test trolley for Switchgear manufacturers for testing of ACB , MCB , MCCB. It is low Voltage high Current source with control circuitry, digital read out for test current and trip time measurement. We can select different links of CT range as per the required test Current.
-
product
PMC to PCI adapter
3390
PMC to PCI adapter - permits operation of PMC in a PCI slot for engineering development
-
product
4U Compact 42HP CompactPCI Serial Chassis Platform
CPCIS4VC800
The CPCIS4VC800 is a 4U vertical-mount chassis that holdsup to eight 3U slots at a 0.8” pitch. The modular card guidescan be adjusted to allow 1.0” pitch or other spacing in .2”increments. The standard PSU is a fixed 350W ATX, but other options are available. Conduction-cooled card guides arealso available for testing and development.
-
product
Go No Go Testers
Go No Go Testers are developed in portable formats. Typically these are utilized at 'I' Level and 'O' Level test requirements and clear the aircraft LRU for flight.
-
product
Super MUTT Deluxe Standard Edition
#9008-SE
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
product
Low Power RF Transceivers
Analog Devices provides a wide range of low power RF transceivers covering sub-GHz and 2.4 GHz frequency bands. Drawing on over 40 years of experience designing high performance RF ICs, the ADF7xxx family of transceivers delivers industry-leading RF performance combined with ultralow power consumption. Our latest transceivers incorporate configurable packet handling capability for proprietary and industry standard protocols to address emerging Internet of Things requirements. As faster time to market grows in importance, evaluation platforms such as the latest ADF7xxxMB4Z will be critical to kickstarting software development.
-
product
Integrating Sphere Spectroradiometer System for LED
LPCE-2(LMS-8000)
LPCE-2(LMS-8000) is an Integrating Sphere Spectroradiometer LED Testing System for identifying the performance of single LEDs and LED lamps. LED’s quality should be tested by checking its photometric, colorimetric and electrical parameters. According to CIE 127-1997 and IES LM 79-08 standards, it recommends using an array spectroradiometer with integrating sphere and photometer head to test SSL products. LISUN GROUP developed LPCE-2 test system for LED products.
-
product
Functional Test Systems
With extensive experience in functional test equipment, a world-wide service and support organization, and a broad range of software/hardware options, we will supply cost-effective production-ready test solutions to meet your test challenges. Proposals developed by our functional test engineering team include a detailed description of system requirements, test instrumentation, estimated test cycle times (as applicable), footprint, and other key specifications.
-
product
Evaluation boards
iSYSTEM evaluation and development systems are optimized for evaluation of the featuring microcontroller whether it fits the project requirements or for the development of the target application while the hardware is still in the design stage. Our systems are distinguished by high speed debug and trace connection to experience the full microcontroller capabilities.
-
product
Precision Thermometer
F252
ASL's F252 provides high accuracy, dual channel temperature measurement with Platinum Resistance Thermometers - PRTs - and uses AC bridge technology as developed by ASL for Standards Laboratories throughout the world. Model F252 requires no regular recalibration, the AC circuit techniques eliminating thermal EMFs and drift, while providing excellent long term stability. Front panel data entry allows you to enter probe calibration data into the F252's memory, so that thermometer resistance can be accurately converted to temperature in C, F or K. This can be password protected to prohibit unauthorised or accidental data entry.
-
product
9U CPCI, Type 39 E-Frame, Test Platform (Short)
39E-CPCI
The Type 39 E-Frame (Short), test platform supports 3U, CPCI development. With a rugged aluminum construction, the 39 E-Frame is 9U overall to hold 3U cards. Available in compact (49HP) and full (84HP) widths for mounting 2-21 slots at .8" pitch.
-
product
Adapter/ Stainless Steel
WADP-35F35F
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
RZ Family of 64-Bit & 32-Bit Arm-Based High-End MPUs
RZ/N
RZ/N Series is a family of scalable and performant Arm® based communication devices that support multiple Industrial Ethernet protocols. An API towards the application software makes the communication software transparent and lets developers focus on what they know best - solving customers’ problems.
-
product
Application Specific LC Systems
Method Scouting System
Method Scouting System is a method development system based on Shimadzu’s UHPLC technology. The combination with Method Scouting Solution dedicated control software achieves a fast and accurate method scouting workflow, offering excellent support for method development.
-
product
Software Capabilities
In test system development, the best hardware is only usable if its software control environment is robust and easy to use. If you are a test system developer, you need to look at both the hardware and software aspects of your vendors of choice.
-
product
I/Q Signal Generation for Digital Radio Standards
WinIQSIM2
R&S®WinIQSIM2™ was especially developed to easily generate digitally modulated signals on a PC. The graphical user interface allows intuitive operation by offering a convenient way to create standard-conforming waveforms for many configurable digital standards and to generate multicarrier signals and multisegment waveforms. With these capabilities, R&S®WinIQSIM2™ covers a wide range of applications.
-
product
ARINC 615A Software Data Loader and Loader Target Development Kits
Avionics Interface Technologies
AIT provides 615A software libraries which can be embedded into a variety of host avionics systems to support both data loader and target side ARINC 615A operations.
